Chamberlain 1022 - Manuals

PN# 3642036534, 02/26/2010 REV. 1 5 TYPICAL SECTIONAL DOOR INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM TYPICAL SUPPORT BRACKET (NOT PROVIDED) EXTENSION SPRING OR TORSION SPRING SAFE-T-BEAM ® BRACES ADDED HEADER BRACKETMOUNTING BOARD POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLE...

PN# 3642036534, 02/26/2010 REV. 1 6 RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 3/16" Drill Bit 1/4", 7/16", 3/8" and 1/2" Sockets Step ladder Drill Ratchet Carpenter’s level Pencil Tape measure Wire strippers Phillips screwdriver Adjustable wrench PARTS IDE...

PN# 3642036534, 02/26/2010 REV. 1 FASTENERS - Shown Full size (See Parts List below for full description.) Lag screw - 5/16" x 2" Self-drilling Screw 1/4"-20 x 3/4" Hex Flange Nut 1/4"-20 Cotter pin Clevis pin 5/16" x 3/4" Hex Bolt - 5/16"-18 x 3/4" Hex Flange Nut...

PN# 3642036534, 02/26/2010 REV. 1 8 1-PIECE RAIL HARDWARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 3-PIECE RAIL HARDWARE ASSEMBLED VIEW Tensioner Rail with chain Chain Chain Connector Release Knob Header Bracket Power Head Power Cord Carriage Assembly Clevis Pin, Long & Cot...

PN# 3642036534, 02/26/2010 REV. 1 9 PENER ASSEMBLY FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 1 NOTE: Three (3) piece rail assemblies are for a 7foot high door. Clear a workspace area to unpack and organize boxand contents for assembly. 1. There are 4 boxes inside the carton. Each box is number...

10 FIG. 1-2 Split Rail sections . FIG. 1-3 Split Rail assembly . A B Chain Rail Center Rail End Rail Wire Tie(s) Rail Assembly for CHAIN DRIVE OPENER NOTE: For split rail clamps, nuts, and boltslocate Bag 0 from Box 1. 3. Remove the two rail sections that are not connected to the chain and place the...

POWER HEAD & RAIL ASSEMBLY Assembly for CHAIN DRIVE OPENER NOTE: Handle carefully! Drive chain can slide out of rail.NOTE: For power head and rail assembly locateBag 1 from Box 1.NOTE: Copy serial number from power headframe and record it on warranty page. NOTE: Standing at the powerhead, facing...

12 PN# 3642036534, 02/26/2010 REV. 1 FIG. 2-2 Finding highest point of travel . NSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 2 HEADER AND DOOR MOUNTING BRACKETS: 1. Finding header bracket mounting location . • Close garage door. – Use a pencil and level. a) Mark center of garage door ...

MOUNTING THE OPENER: 1. Getting started . • Position assembled rail on wall next to header bracket (Fig. 2-4) . – Place material on floor under power head to protect from scratching. (A box, stool, or similar device may be needed to clear a torsion spring.) NOTE: For header bracket pins locate Bag 2...

14 PN# 3642036534, 02/26/2010 REV. 1 DOOR BRACKET: NOTE: For door bracket and bolts locate Bag 4from Box 2. 1. Finding door bracket mounting location . • Door bracket is mounted as high on door as possible along vertical centerline and NO LOWER THAN top set of rollers (Fig. 2-7) . 2. Mounting the do...

PN# 3642036534, 02/26/2010 REV. 1 NOTE: For Wall Console, wire and insulated staples locate Bags 6 and 7 from Box 2. 1. Wall Console location. ‡ Wall Console location should be in direct sight of door. ‡ It should be at least five feet (5') above floor to prevent small children from operating door. ...

PN# 3642036534, 02/26/2010 REV. 1 16 3.Securely fasten wires. ‡ Securely fasten wires to ceiling and wall using insulated staples provided.– Use insulated staples.– Staples should be snug only. ‡ If rear cover is attached to power head, remove it. ‡ On power head:– Route wall console wires through w...

PN# 3642036534, 02/26/2010 REV. 1 17 AFE-T-BEAM ® SYSTEM INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 4 NOTE: The opener will not close the door automatically unless the Safe-T-Beam ® System is installed. NOTE: For Safe-T-Beam®, screws, wire, and insulated staples locate items and Ba...

PN# 3642036534, 02/26/2010 REV. 1 18 3b. Wiring (pre-wired) . ‡ Route wire from wall to Safe-T-Beam ® sensors (Fig. 4-5b) . ‡ Splice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash and plain-to-plain . - Trim sensor wire to approximately one foot (1 ft) from sensor. - Split and st...

PN# 3642036534, 02/26/2010 REV. 1 19 ONNECTING TO POWER FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 5 Plug the opener into a properly grounded electrical outlet (Fig. 5-1). ‡ To reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third ( grounding ) pin. ...

PN# 3642036534, 02/26/2010 REV. 1 20 OOR LIMITS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 6 The OPEN (UP) and CLOSE (DOWN) door positionsare controlled by making the adjustments on thepanel located on the bottom of the power head. Theadjustments that can be made are: • Close Travel Limit, • Op...

21 Obtain standard emergency release kit and remove S-hook from the cable end that attaches to the opener carriage. 1. Attach the emergency release cable loop end to the opener carriage as shown (FIG 6-4). Properly connecting the release cable to the carriage fitting will enable the correct carriage...

PN# 3642036534, 02/26/2010 REV. 1 22 FIG. 6-6 2 x 4 under center of door opening. CONTACT REVERSE TEST The force adjustments and limit switch settingsMUST BE COMPLETED before testing. 1. Testing . ‡ Open garage door using wall button.– Place a 2" x 4" board (laid flat) under center of garage...

PN# 3642036534, 02/26/2010 REV. 1 23 FCC and IC CERTIFIED FIG. 7-1 Learn code button and LED SET SET OPEN FORCE CLOSE CODE LEARN LIMIT MANUAL Open Travel Limit Open Set Limit Button Close Travel Limit Close Set Limit Button Down Force Control Adjustment Up Force Control Adjustment Learn Code Button ...

EMOTE CONTROL BATTERY REPLACEMENT AND VISOR CLIP INSTALLATION 8 FIG. 8-1 Open battery cover . 1. Battery replacement . • To open gently push straight out on battery cover lock tab as shown (Fig. 8-1) . • Flip open battery cover. – Remove old battery. • Make sure new battery is facing proper directio...

PN# 3642036534, 02/26/2010 REV. 1 25 Use wall button supplied with opener. Any other wall control can causethe opener to operate unexpectedly. WARNING If you have any questions, please do not hesitate to contact Genie ® customer service at: 1.800.354.3643 IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FO...

PN# 3642036534, 02/26/2010 REV. 1 26 CIRCUIT WIRING DIAGRAM FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 1 2 3 4 5 6 1 2 3 4 1 2 3 1 2 POWER CORD CORDON DE SECTEUR CABLE ELÉCTRICO TERMINAL BLOCK BORNE BLOQUE DE TERMINALES WHITE BLANC BLANCO BLACK NOIR NEGRO GREEN VERT VERDE SURGE PROTECTOR (MOV) ...

PN# 3642036534, 02/26/2010 REV. 1 27 TROUBLESHOOTING GUIDE - OPERATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM PROBLEM WHAT TO DO Opener does NOT runfrom Wall Console. ‡ Check power source.– Plug a lamp into outlet used for power head. If lamp works, power source is OK.– If not, check fuse o...

PN# 3642036534, 02/26/2010 REV. 1 TROUBLESHOOTING GUIDE - POWER HEAD LED FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Power head LED Possible Problem Solution Red LED showing Green LED showing OFF OFF Normal operation None required Continuous ON ‡ Programming incomplete ‡ Complete programming 1 B...

PN# 3642036534, 02/26/2010 REV. 1 29 Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is madethat they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country, the importermus...

GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified opener Model 1022 or opener Model 1024 or opener Model 1042 (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free...