Central Pneumatic 33567 - Manual

Page 2 - SPECIFICATIONS; RATCHET WRENCH; SAVE THIS MANUAL; READ ALL

SPECIFICATIONS RATCHET WRENCH — Average Air Consumption 4 CFM Recommended Air Pressure 90 PSI Air Inlet ¼” NPT Free Speed 150 RPM Maximum Torque (ft. lbs.) 45 IMPACT WRENCH — Bolt Capacity 1/2" Speed 7000 RPM Air Inlet ¼” NPT Sockets 7/16" – 1" Maximum Torque (ft. lbs.) 230 SAVE THIS MAN...

Page 5 - GROUNDING INSTRUCTIONS; If compressor has a three-prong plug

GROUNDING INSTRUCTIONS If compressor has a three-prong plug 1. This machine has a three-prong plug. The third prong (round) is the ground. Plug the machine’s cord only into three-prong receptacles. Never cut off the round prong. Cutting offthe ground will result in a safety hazard and void the warra...

Page 6 - UNPACKING; ASSEMBLY; Your Air Ratchet comes completely assembled.; Impact Wrench; Description; Oil Pot

UNPACKING When unpacking, check to make sure the following parts are included. All sizes listed below areapproximate. If any parts are missing or broken, please call Harbor Freight Tools at the numberon the cover of this manual. ASSEMBLY Your Air Ratchet comes completely assembled. Air Connection fo...

Page 7 - Setup; ONLY USE PNEUMATIC TOOL OIL.; Do not use detergent oil or

Air Ratchet OPERATION Setup Frequent, but not excessive, lubrication is required for best performance. Oil added through theairline connection will lubricate internal parts. An automatic airline oiler is recommended but oilmay be added manually before every operation or after about 1 hour of continu...

Page 8 - Air Inlet

Step 2: Attach the socket to the RATCHET ANVIL (#18) as shown in Figure 2. Step 1: Select the appropriate socket for your needs. Air Ratchet Operation Figure 2 — Attaching the Socket Step 3: Set the compressor’s pressure regulator to 90 PSI. Do not set the compressor’s outlet regulator over 90 PSI. ...

Page 9 - Loosening; Figure 3 — Operating the Air Ratchet

Step 1: Check the direction of the drive by pressing the TRIGGER (#4) as shown in Figure 3. Loosening Figure 3 — Operating the Air Ratchet Step 2: If the Air Ratchet is going counterclockwise (the correct direction to loosen), then proceed to Step 4. Step 3: To change the direction of the drive to l...

Page 11 - MAINTENANCE; Step 1: Disconnect the Air Ratchet from the air hose.; PNEUMATIC TOOL; through the air inlet before each use,; CAUTION; Do not use detergent oil or additives as; Figure 6 — Lubrication Points

MAINTENANCE Your Air Ratchet is best operated with an Airline Oiler. If you are using the Air Tool without anAirline Oiler, follow the steps below. Step 1: Disconnect the Air Ratchet from the air hose. Step 2: Apply a few drops of PNEUMATIC TOOL OIL through the air inlet before each use, or every ho...

Page 12 - Impact Wrench Operation; tory without harming this tool.; Figure 7 — Attaching the Air Coupler and Socket; disconnect the air hose and repair before use.

Impact Wrench Operation Step 1: Set the compressor’s pressure regulator to a maximum of 90 PSI. 90 PSI is satisfac- tory without harming this tool. Step 2: Remove the plastic cap from the rear of the HOSE ADAPTER (#10). Step 3: Wrap the threads of the Air Coupler with pipe thread seal tape (not incl...

Page 14 - freely as shown if Figure 10.; Figure 10 — Pressing Trigger; WARNING; The Impact Wrench May Kick Back

Step 8: Press the TRIGGER (#4) to test the Impact Wrench. The Impact Wrench should spin freely as shown if Figure 10. Figure 10 — Pressing Trigger Loosening Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (#3) has been shifted (pressed) completely to the righ...

Page 15 - Tightening; WARRANTY

Tightening Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (#3) has been shifted (pressed) completely to the left. If not, refer to Steps 6 through 7under Impact Wrench Operation before proceeding. Step 2: Place your work in as clear a location as possible. M...

Page 16 - PARTS LIST – RATCHET WRENCH

PARTS LIST – RATCHET WRENCH Item# Parts No. Description Item# Parts No. Description 1 HY150-01 Housing 23 HY150-23 Ratchet Yoke 2 HY150-02 Connection Head 24 HY150-24 Cylinder 4 HY150-04 Trigger 25 HY150-25 Rotor 5 HY150-05 Roll Pin 26 HY150-26 Rotor Blade 6 HY150-06 Valve 27 HY150-27 Front Plate 7 ...

Page 17 - Exploded View Diagram - Ratchet Wrench

Exploded View Diagram - Ratchet Wrench Page #17 -- SKU: 33567 REV 12/02 For technical questions, please call 1-800-444-3353.

Page 18 - PARTS LIST – AIR IMPACT WRENCH

PARTS LIST – AIR IMPACT WRENCH Item# Parts No. Description Item# Parts No. Description 1 16001 Housing 23 16023 Ball Bearing (X2) 2 16002 Valve Sleeve 24 16024 Cylinder 3 16003 Reverse Valve 25 16025 Rotor 4 16004 Trigger 26 16026 Rotor Blade (X6) 5 16005 Spring Pin 27 16027 Front End Plate 6 16006 ...

Page 19 - Exploded View Diagram -- Air Impact Wrench

Page #19 -- SKU: 33567 REV 12/02 Exploded View Diagram -- Air Impact Wrench For technical questions, please call 1-800-444-3353.