CatEye CC-MT400 - Manual
CatEye CC-MT400 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – (excluding the attached parts and deteriorated battery ); MODE; Measurement Display; Av; Setting The Clock Time; Computer Operations; Hour; Av; Standard Parts
- Page 3 – Conservez la valeur actuelle de l’odomètre; La préparation est terminée.; L cm; Entrez la valeur actuelle de l’odomètre.; Installation du compteur sur votre vélo; Remarque importante; Remarque importante; à 5 mm ou; CAT EYE MITY 8; F: Manuel de l’utilisateur; OK
- Page 4 – Affichage des mesures; Régler l’heure; Opérations du compteur; Heure; Pièces standard
- Page 5 – Vorbereitungen beendet.; (In diesem Status wird der Bildschirm die Uhrzeit anzeigen); Installation des Computers an ihrem Fahrrad; Wichtiger Hinweis; Wichtiger Hinweis; lediglich 5 mm beträgt; G: Bedienungsanleitung
- Page 6 – Messung Display; Uhrzeit einstellen; Betrieb des Computers; Stunde; Standardteile
- Page 7 – (初めて使うとき・電池交換した後); 積算距離を引継ぐとき; 準備完了; (計測画面・走行時間へ); 予めタイヤの周長(L cm); タイヤ周長ガイド; 自転車への取付け; 重 要; お使いの前にこの説明書を最後までよくお読みください。; サイクロコンピュータ
- Page 8 – 製品仕様; (水晶発振器); 製品保証について; 年保証:コンピュータのみ(付属品及び電池の消耗は除く); はお客様にてご負担願います。修理完了後、当社より郵送にてお届けさせていただきます。; [宛先]; *アクセサリーパーツを別途販売していますのでご利用ください。; アベレージペースアロー; オートモードアイコン; タイヤ周長アイコン; 計測画面; 時刻; タイヤ周長 と を切替えるには; 選択(下段)データの切替え; 平均速度; Odo; 積算距離; Mx; 最高速度; Dst; 走行時間; 時刻を合わせる; トラブルと処理; コンピュータの操作; MODEボタンを押すと選択データは右図(計測画面); 分 秒
Important
Note
Warning
• Pay attention to the road or trail! Do not be distracted by the
computer.
• Be sure to securely mount the magnet, the sensor, and the
bracket on your bicycle. Periodically check to insure they are
mounted securely and the screws are not loosen.
• Keep batteries out of reach of small children. Dispose of batter-
ies according to local regulations.
• Avoid unnecessary prolonged exposure to the sun. Never at-
tempt to disassemble the computer head.
• Don’t use thinner, benzene or alcohol to wipe the surface of the
computer. They may damage the surface of computer.
Computer Set-up
(For 1st use or after replacing the battery)
All Clear
Push three buttons (MODE, START/
STOP and SET) at the same time.
* Do this procedure without fail for
stable measurement when you use
this system for the first time and every
time the battery is replaced.
1
Starting the odom-
eter from zero.
Retaining the current odometer reading
(the odometer starts from the reading you
inputted)
SET
MODE
MODE
ST/STOP
ST/STOP
Set The Tire Circumference
Set the tire circumference in cm.
Note
You can easily set it by referring to the chart shown
right.
Setting is completed by pushing the SET button.
3
Increase the
number.
Max. 300 cm
Decrease
the number
Min. 100 cm
Preparation Complete.
(the screen will show the time measurement in this state)
* The auto mode is ON in this state.
MODE Button
START/STOP Button
SET Button
!
L(cm)
14 x 1.50
102
14 x 1.75
106
16 x 1.50
119
16 x 1.75
120
18 x 1.50
134
18 x 1.75
135
20 x 1.75
152
20 x 1-3/8
162
22 x 1-3/8
177
22 x 1-1/2
179
24 x 1
175
24 x 3/4Tubular
178
24 x 1-1/8
179
24 x 1-1/4
191
24 x 1.75
189
24 x 2.00
192
24 x 2.125
196
26 x 7/8
192
26 x 1(59)
191
26 x 1(65)
195
26 x 1.25
195
26 x 1-1/8
190
26 x 1-3/8
207
26 x 1-1/2
210
26 x 1.40
200
26 x 1.50
201
26 x 1.75
202
26 x 1.95
205
26 x 2.00
206
26 x 2.10
207
26 x 2.125
207
26 x 2.35
208
26 x 3.00
217
27 x 1
215
27 x 1-1/8
216
27 x 1-1/4
216
27 x 1-3/8
217
650 x 35A
209
650 x 38A
212
650 x 38B
211
700 x 18C
207
700 x 19C
208
700 x 20C
209
700 x 23C
210
700 x 25C
211
700 x 28C
214
700 x 30C
217
700 x 32C
216
700C Tubular
213
700 x 35C
217
700 x 38C
218
700 x 40C
220
L cm
SET
ST/STOP
MODE
Contact Point
Select The Measurement Unit
Select the measurement unit, kilometer
or mile, by pushing the MODE button.
2
MODE
Choose Either of The Followings.
• When you want to input the reading of the currently
used odometer, keep pressing the MODE button for
two seconds and input the reading.
• When you want to start the odometer from zero,
push the START/STOP button.
Kilometer
Mile
SET Button
MODE Button
START/STOP
Button
Input the current reading of odometer.
For two seconds.
Increase the
number.
Move the
decimal point.
You need to know the tire
circumference (L cm) be-
forehand.
Tire size
Tire size is usually shown
on the sidewall of tires.
®
3
2
1
Installation of the Computer on Your Bike
The computer is combined with the following parts.
1
2
5
3
6
7
4
3
7
Important Note
Mount the sensor
3
at the appropri-
ate position so that the center of the
m a g n e t
5
w i l l a l i g n w i t h t h e
marked line on the sensor when the
wheel is rotated.
Important Note
Rotate the sensor on the front fork to
adjust the gap between the sensor
and the magnet
5
within 5 mm, and
secure it with the nylon ties.
Mount The Bracket
Secure the cord on the front fork with the nylon ties (smaller ones)
7
and coil it around the
brake cable that leads to the handle bar.
Put the rubber pad
6
on the bracket
1
and secure the bracket on the handle bar with the
screw. Slide the computer into the bracket until you hear the click sound
The contact points are automatically closed. When you need to remove the computer, slide
forward the computer with the lever pushed simultaneously.
Note
Allow enough wire clearance in the area marked with an
to insure that you can
turn the handlebar from left to right without pulling the wire.
Basic Functions Test
Rotate the front wheel gently and see if the computer indicates the
running speed.
Note
When the computer does not indicate the speed, check
the position of the magnet and the sensor.
4
3
5
1
Bracket
2
Cord
3
Sensor
4
Sensor Rubber Pad
Center
5
Magnet
6
Bracket Rubber Pad
7
Nylon Ties (5)
Front Fork
3
2
1
Please read these instructions carefully before attempting to
install and use your CAT EYE MITY 8 computer so that you
understand the functions of this product.
Please don’t throw away this manual, Keep the manual at a place easily accessible.
5
Spoke
Rotate the front wheel.
OK
7
Front Fork
Sensor Side
Within 5 mm
Marked Line
1
Slide
1
6
Mount sensor and adjust the gap between the
magnet and the sensor.
Secure the sensor
3
with the larger nylon ties
7
at
the appropriate place and in the right direction.
Mount the magnet
5
on a spoke of the front wheel so that the surface
of the magnet will face the sensor.
Lever
MITY8
CAT EYE MITY 8
CYCLOCOMPUTER CC-MT400
E: Owner’s Manual
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending
Copyright © 2002 CAT EYE Co. Ltd.
CCMMT4-021210 066600230
1
You can refer to the guide
chart to roughly know the
tire circumference.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Specifications Battery Life : --------------------------------- A Lithium Battery (CR2032), Approx:3 yrs (approx:1 hrs per day usage) Control System : ---------------------------- 4-bit 1-chip micro-computer (with a crystal oscillator)Display : -------------------------------------- Liquid crystal d...
5 3 Remarque importante Attention • Faîtes attention à la route ou à la piste ! Ne vous laissez pas distraire par le compteur. • Assurez-vous de bien fixer l’aimant, le capteur et le support sur votre vélo. Vérifiez régulièrement pour vous assurer qu’ils sontfixés correctement et que les vis sont bi...
Spécifications Durée de vie de la pile : --------------------- Une pile au lithium (CR2032), Env. : 3 ans (env. : 1 heure par jour d’utilisation) Système de contrôle : ---------------------- Une puce de micro-ordinateur 4 bits (avec un oscillateur à cristal)Affichage : ------------------------------...
