CatEye CC-AT100 - Manuals

E 5 FOR SAFE OPERATIONS (IMPORTANT) For safe and appropriate use, always observe the following. Caution: • Don't pay too much attention to your cyclocomputer functions when riding. Keep your eyes on the road and give due consideration to safe riding. • This altimeter is not intended to be a speciali...

E 6 Battery Cover Close Open CR2032 Fig.1 SET UP 1. How to Put in a Battery 1. Remove the battery cover on the back with a coin or a similar opener (Fig. 1).2. Insert a new lithium battery (CR2032) with the (+) pole upward as illustrated. Close the cover securely.3. Press the AC button, and reset th...

E 7 -3. Setting Temperature Scale When the process of setting speed scale is completed, " ° C" symbol illuminates (Fig. 4). With each press of the S/S button, " ° C" and " ° F" appears alternately. Select the desired scale and press the Set button to fix the scale. -4. Settin...

E 8 • Each main mode has its respective sub mode. To switch to the sub mode, hold down this button. To switch back to the main mode from the sub mode, just press this button ordinarily. To shift from onemode to another, it is necessary to switch back to the main mode (from the sub mode) each time. B...

E 9 R e s e t When the S/S button and the Mode button are pressed simultaneously, the following data can be reset, depending on the mode. For resetting trip distance(D), elapsed time(T), average speed(A) and maximum speed (M): In other modes than altitude measuring mode, press the two buttons simult...

E 10 may cause even a greater change. In seemingly stable weather conditions, youmay expect to see the Altitude fluctuate as much as 100 feet from morning toevening because of the warming aspects of the sun on the atmosphere. 2. Cycling Mode (Bicycle Symbol: on) (Fig. 10) When using this unit on bic...

E 11 How to Correct the Altitude First display the main mode showing , with the operation of the Mode button. Press the Set button when the speed is zero, and it turns to the correction mode (Fig.13). The figure increases witheach press of the S/S button, and decreases with each press of the Mode bu...

E 12 • Secure the wire with the wire securing tape as in Fig. 20. Wind the wire round the outer cable up to the handlebar. When ad-justing the length, be careful that the wire will not hinder handle-bar operation. • By using the rubber pad, attach the bracket close to the handle- bar stem (Fig. 21)....

E 13 3. Power Saving Function When the main unit is left without receiving any signal for about 5 minutes continuously, powersupply is shut down and the unit will be in "sleep" state displaying only the clock time (Fig. 24). Byreceiving a signal from the wheel, or by pressing the S/S button ...

E 15 M Maximum Speed (Sub Mode) Displays the maximum instantaneous speed on the sub display. With the Reset operation, it returnsto zero. 0.0 (2.6) - 105.9 km/h [0.0 (1.6) - 62.9 mile/h] ° C/ ° F Temperature (Sub Mode) Measures the current atmospheric temperature in every 20 seconds and displays the...

E 16 Incorrect data appears. The static electricity may cause an incorrect display.Press the AC button and reset the speed scale and the clock time again. Current speed does not appear. Is there anything on the contact of the main unit or the bracket?Wipe the contact clean. Is the distance between t...

E 18 SPECIFICATIONS Display Ranges Current Speed S 0.0(2.6) - 105.9 km/h (27 inch) ± 0.5 km/h (under 50 km/h) [0.0(1.6) - 62.9 mile/h ± 0.5 mile/h (under 31 mile/h)] Total Distance O 0.0 - 42949 km [mile] ± 0.1 km [mile] Maximum Speed M 0.0(2.6) - 105.9 km/h (27 inch) ± 0.5 km/h [0.0(1.6) - 62.9 mil...

E 19 SETTING VALUES CROSS REFERENCE TABLE *The tire size is marked on both sides of the tire. LIMITED WARRANTY 2-Year Warranty: Only Main Unit (excluding battery) If trouble occurs during normal use specified in this manual, the part is repaired or replaced free of charge. The service must be perfor...