Casablanca Metropolitan - Manual

Page 2 - CONTENTS; READ AND SAVE THESE INSTRUCTIONS; For best performance and for your warranty to be valid,; SAFE USE; SAFETY FIRST; INTELI•TOUCH OPERATION; BEFORE YOU START

1 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) CAUTION: MOUNT WITH THE LOWEST MOVINGPARTS AT LEAST 2.5 METRES ABOVE FLOOR ORGRADE LEVEL.ATTENTION: INSTALLER DE SORTE QUELESPIÈCES INFÉRIEURES SOIENT À AU MOINS 2.5M...

Page 3 - Calculation of 32; SLOPED CEILING INSTALLATIONS; Pole Length

2 Calculation of 32 ° Use the tear-off Ceiling Angle Template card inserted in the back of this manual, it provides you with a simple ‘go’ or‘no-go’ for installing your fan on a sloped ceiling. SLOPED CEILING INSTALLATIONS MOUNTING RECOMMENDATIONS 7 ′ MINIMUM Pole Length StandardStandard 6 ″ 12 ″ 12...

Page 4 - Installing a New Ceiling Fixture Outlet Box; PERMA•LOCKTM HARDWARE; ETROPOLITAN; IMPORTANT SAFETY INFORMATION!

3 INSTALLATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. CEILING HARDWARE CROSSBAR MOUNTING BRA...

Page 5 - CROSSBAR MOUNTING BRACKET INSTALLATION; CANOPY INSTALLATION

4 Step 2. Attach the canopy to the crossbar mount- ing bracket with three of the 8-32 x 2 1 / 4 ″ long canopy screws and canopy lock washers. Handtighten until snug against the ceiling. CAUTION: To reduce the risk ofpersonal injury, use only themounting hardware provided withthe approved outlet box ...

Page 6 - Electrical Connections; CANOPY HATCH INSTALLATION

5 Step 3. To hang the fan body in the canopy, hold the fan body firmly and in-sert the nylon ball into the canopyopening. Check that no wires werepinched. Rotate the fan body until theslot in the nylon ball fits into the pinopposite the canopy opening. HANGING THE FAN PIN SLOT BALL CANOPY ELECTRICAL...

Page 7 - BLADE/BLADE HOLDER INSTALLATION; ASSEMBLE BLADE HOLDER & BLADE

6 BLADE/BLADE HOLDER INSTALLATION Step 9. Rotate the flywheel so that the screw holes can be accessed through therecessed area of the metal plate. Attach each blade/blade holder assem-bly to the motor. Tighten securely by hand only. BLADE HOLDER SCREW (2 PER BLADE) Step 8. Attach the blades to the b...

Page 8 - INSTALLING THE SWITCH HOUSING CAP; INTELI•TOUCH = PAGE 8 COMFORT•TOUCH = PAGE 12; PREPARING TO INSTALL SWITCH HOUSING CAP

7 INSTALLING THE SWITCH HOUSING CAP Step 11. Line up the three threaded holes inthe rim of the switchhousing with the threeclearance holes in themounting plate. Carefullyslide the switch housinginto the mount so thatthe threaded holes aredirectly behind the clear-ance holes. S t e p 1 2 . I n s t a ...

Page 9 - only; INTELI•TOUCH; INTELI•TOUCH© INSTALLING THE W-32 WALL CONTROL

INTELI•TOUCH ♦ ♦ ♦ ♦ ♦ SINGLE W-32 INSTALLATION The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. Thiscontroller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason thefollowing...

Page 10 - FAN CONTROL

9 INTELI•TOUCH OPERATION ♦ POWER + + + + Programmed into every Inteli-Touch Series fan is an Auto-matic Demonstration Program. It can be used to fullydemonstrate and test the operation of the fan. To enter the demonstration program: 1. Turn off for at least three seconds. This will clear the fan mem...

Page 12 - TROUBLESHOOTING; PROBLEM

11 TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleanerbrush nozzle can remove heavier du...

Page 13 - Battery Installation; Remove for handheld or tabletop use; Mount control in convenient location; Installation of Remote Control; Low Battery Indicator

12 + - + - + - REMEMBER THE REMOTE CONTROL WILL GO BACKTO THE ORIGINAL FACTORY ‘PRESET CHANNEL’NUMBER WHEN THE BATTERIES ARE CHANGED.CHANGE CONTROL CHANNEL IF NECESSARY AFTERBATTERY REPLACEMENT. Battery Installation Install three ‘AAA’ alkaline batteries in the sequence shown andreplace the battery ...

Page 14 - Labeling; COMFORT•TOUCH; Power Failure

13 R COMFORT•TOUCH ♦ TEST PROGRAM COMFORT•TOUCH ♦ LIGHT OPERATION COMFORT•TOUCH ♦ FAN OPERATION The light is turned on and off by alternate pushes of thelarge left hand button. When on, the display will indicatethe light bulb symbol and a vertical segment display repre-senting brightness. When the l...

Page 15 - Temperature Accuracy; Pressing any button on the remote will cancel the

14 Pressing the REVERSE button will change the direction of rotation. An audio tone signals the beginning of the reverse sequence and you will see the airflow direction arrowchanging. The fan gradually slows to a stop, then reverses direction. REVERSE COMFORT•TOUCH ♦ AUTO-SPEED FEATURE In the Auto S...

Page 16 - TWO CONTROLS OPERATING ONE FAN

15 REMOTE CONTROL CHANNEL NUMBER A second remote control can be purchased from your dealer to providedual remote control of one fan. Because the fan could be confused bytwo controllers signaling different information it is necessary to set a BASE control and an AUXILIARY control. The last control ma...

Casablanca Metropolitan - Manual

Table of Contents:

Summary

Other Casablanca Models