Casablanca 54005 - Manual

1.888.227.2178 www.CasablancaFanCo.com Ceiling Bracket Installation OFF Make sure all four (4) bumpers are still attached. For angled ceilings, point opening toward peak. Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off...

www.CasablancaFanCo.com 1.888.227.2178 Ceiling Bracket Installation (continued) Preparation DISCA RD KEEP! Remove the shipping blocks from the motor. Save the five screws. They will be needed for blade iron installation. 1.888.227.2178 www.CasablancaFanCo.com Time Saver Tip: Get a helper to insert g...

1.888.227.2178 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a d...

KEEP! 8” 3/8” CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downrod. Downrod (continued) 8” 3/8” Tig...

www.CasablancaFanCo.com 1.888.227.2178 9 M6004-01 • 08/13/12 • © Casablanca Fan Company Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling b...

www.CasablancaFanCo.com 1.888.227.2178 Wiring FR O M F A N F RO M C E I LING B RA CK E T F R O M FA N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. (G rounding) ...

www.CasablancaFanCo.com 1.888.227.2178 11 M6004-01 • 08/13/12 • © Casablanca Fan Company Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Screw Holes Insert the two canopy sc...

www.CasablancaFanCo.com 1.888.227.2178 M6004-01 • 08/13/12 • © Casablanca Fan Company Blades Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws f...

www.CasablancaFanCo.com 1.888.227.2178 Switch Housing Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not ...

www.CasablancaFanCo.com 1.888.227.2178 Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Lift the lower switch housing up until the holes line up with the screw holes in the upper switch housing. Light Kit Remove the socket rings...

www.CasablancaFanCo.com 1.888.227.2178 M6004-01 • 08/13/12 • © Casablanca Fan Company 16 Maintenance & Cleaning The pull chain controls the fan: high, medium, low, extra low, and off.The light pull chain controls the power to the light fixture: on and off. To switch the direction of air flow, mo...

www.CasablancaFanCo.com 1.888.227.2178 17 M6004-01 • 08/13/12 • © Casablanca Fan Company Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. • Use...