Casablanca 46U4D - Manual - manualsarea.com

Page 2 - CONTENTS; READ AND SAVE THESE INSTRUCTIONS; For best performance and for your warranty to be valid,; SAFE USE; SAFETY FIRST; BEFORE YOU START

1 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) 18 ″ 84 ″ 70 ″ • The blades in each pack are matched for equalweight to assure smooth fan operation. Ifmore than one fan is being installed, becareful not to mix blad...

Page 3 - Calculation of 32; SLOPED CEILING INSTALLATIONS; Pole Length

2 Calculation of 32 ° Use the tear-off Ceiling Angle Template card inserted in the back of this manual, it provides you with a simple ‘go’ or‘no-go’ for installing your fan on a sloped ceiling. SLOPED CEILING INSTALLATIONS MOUNTING RECOMMENDATIONS 7 ′ MINIMUM Pole Length StandardStandard 6 ″ 12 ″ 12...

Page 4 - Installing a New Ceiling Fixture Outlet Box; IMPORTANT SAFETY INFORMATION!; BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN,; PERMA•LOCKTM HARDWARE; APISTRANO

3 PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check themagainst the parts listed here. Before discarding packaging material, be certain that all parts have been removed. CEILING HARDWARE CROSSBAR MOUNTING BRACK...

Page 6 - CANOPY HATCH INSTALLATION; Fan Hanging Weight

5 CANOPY ELECTRICAL CONNECTIONS Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by sideand then securing with a wire nut. Test that the connectionis secure by pulling on the wire nut. Connect in this order: Step 4b. • GREEN leads from...

Page 7 - BLADE & BLADE HOLDER HARDWARE; RUBBER GROMMET INSTALLATION; CORRECT INSTALLATION; INSTALLING THE BLADE/BLADE HOLDER TO FAN MOTOR

6 RUBBER GROMMET (4 PER BLADE) BLADE SCREW (4 PER BLADE) BLADE & BLADE HOLDER HARDWARE BLADE HOLDER BLADE HOLDER SCREW (2 PER BLADE) Step 9. Insert a rubber grommet through each blade hole of every blade. Inspectboth sides of the blade to assure thatthe lips of the grommet are fully engaged. RUB...

Page 8 - BLADE/BLADE HOLDER INSTALLATION; BLADE INSTALLATION; REMOVE SHIPPING BLOCKS

7 BLADE/BLADE HOLDER INSTALLATION Step 12. Using the five screws removed in Step 11, and the five additional screws fromthe pack, attach each blade/blade holder as-sembly to the motor. Using the screwdriver, tighten securely by hand only. Step 10. Attach each blade to a blade holder securing it with...

Page 9 - COMPLETING INSTALLATION; PREPARATION

8 COMPLETING INSTALLATION Step 14. Hold the switch housing up to the fan and connect the motor plug tothe switch housing socket. The connec-tor is keyed to ensure correct installation. PREPARATION CONNECTING THE SWITCH HOUSING ASSEMBLY Step 13. Locate the switch housing/cap assembly and remove the t...

Page 10 - INSTALLING THE SWITCH HOUSING ASSEMBLY; INSTALLING THE CAP

9 INSTALLING THE SWITCH HOUSING ASSEMBLY Step 17. Line up the two clearance holes in the cap with the two threaded holeson the raised rim of the switch housing.Press the cap onto the switch housing toseat the guide pins into the alignmentholes of the switch housing. Step 18. Using the two (2) 8-32 X...

Page 13 - TROUBLESHOOTING; PROBLEM

12 TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleanerbrush nozzle can remove heavier du...

Casablanca 46U4D - Manual

Table of Contents:

Summary

Other Casablanca Models