Carrier 38BYC- User Manual
Carrier 38BYC– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSPECT EQUIPMENT; Step 2—Install on a Solid, Level Mounting Pad; Unit must be level to within; Step 3—Clearance Requirements; FURNACE COILS; Fig. 2—Connecting Tubing Installation
- Page 3 – Fig. 4—Typical TXV Installation; Fig. 5—Positioning of Sensing Bulb
- Page 4 – Step 10—Make Electrical Connections; Table 2—Accessory Usage; PISTON BODY
- Page 5 – Fig. 8—Line Power Connections; CONTACTOR
- Page 6 – Thermostat, 1 Outdoor Thermostat, or 2 Outdoor Thermostats
- Page 8 – with FK4C Fan Coil and Smart Staging
- Page 9 – Thermostat, 1 Outdoor Thermostat, or Supplemental Heat Relay
- Page 11 – Step 14—Check Charge; LEGEND; FIELD SPLICE CONNECTION; WIRING DIAGRAM NOTES:
- Page 12 – Table 3—Defrost Control Speed-Up
38BYC
12 SEER Split System
Heat Pump
Installation and Start-Up Instructions
NOTE:
Read the entire instruction manual before starting the
installation.
This symbol
→
indicates a change since the last issue.
SAFETY CONSIDERATIONS
Improper installation, adjustment, alteration, service, maintenance,
or use can cause explosion, fire, electrical shock, or other
conditions which may cause death, personal injury, or property
damage. Consult a qualified installer, service agency, or your
distributor or branch for information or assistance. The qualified
installer or agency must use factory-authorized kits or accessories
when modifying this product. Refer to the individual instructions
packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing,
and work gloves. Use quenching cloth for brazing operations.
Have fire extinguisher available. Read these instructions thor-
oughly and follow all warnings or cautions included in literature
and attached to the unit. Consult local building codes and National
Electrical Code (NEC) for special requirements.
Recognize safety information. This is the safety-alert symbol
.
When you see this symbol on the unit and in instructions or
manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and CAU-
TION. These words are used with the safety-alert symbol. DAN-
GER identifies the most serious hazards which will result in severe
personal injury or death. WARNING signifies hazards which
could result in personal injury or death. CAUTION is used to
identify unsafe practices which would result in minor personal
injury or product and property damage.
Before installing, modifying, or servicing system, main elec-
trical disconnect switch must be in the OFF position. There
may be more than 1 disconnect switch. Lock out and tag
switch with a suitable warning label. Electrical shock can
cause personal injury or death.
INSTALLATION RECOMMENDATIONS
NOTE:
In some cases noise in the living area has been traced to
gas pulsations from improper installation of equipment.
1. Locate unit away from windows, patios, decks, etc. where unit
operation sounds may disturb customer.
2. Ensure that vapor and liquid tube diameters are appropriate to
capacity of unit.
3. Run refrigerant tubes as directly as possible by avoiding
unnecessary turns and bends.
4. Leave some slack between structure and unit to absorb
vibration.
5. When passing refrigerant tubes through the wall, seal opening
with RTV or other pliable silicon-based caulk. (See Fig. 2.)
6. Avoid direct tubing contact with water pipes, duct work, floor
joists, wall studs, floors, and walls.
7. Do not suspend refrigerant tubing from joists and studs with a
rigid wire or strap which comes in direct contact with tubing.
(See Fig. 2.)
8. Ensure that tubing insulation is pliable and completely sur-
rounds vapor tube.
9. When necessary, use hanger straps which are 1 in. wide and
conform to shape of tubing insulation. (See Fig. 2.)
10. Isolate hanger straps from insulation by using metal sleeves
bent to conform to shape of insulation.
When outdoor unit is connected to factory-approved indoor unit,
outdoor unit contains system refrigerant charge for operation with
indoor unit of the same size when connected by 15 ft of
field-supplied or factory accessory tubing. For proper unit opera-
tion, check refrigerant charge using charging information located
on control box cover and/or in the Check Charge section of this
instruction.
IMPORTANT:
Maximum liquid-line size is 3/8-in. OD for all
residential applications including long line.
IMPORTANT:
Always install a liquid-line filter drier. Refer to
Product Data Digest for appropriate part number. Obtain filter
drier from your distributor or branch.
INSTALLATION
Step 1—Check Equipment and Job Site
UNPACK UNIT
Move to final location. Remove carton taking care not to damage
unit.
Fig. 1—Model 38BYC
A97005
Visit www.carrier.com
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book 1
4
Tab
5a 5a
PC 101
Catalog No. 563-853
Printed in U.S.A.
Form 38BYC-1SI
Pg 1
10-97
Replaces: 38AYC-1SI/38-6SM
→
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Carrier 38BYC
Summary
INSPECT EQUIPMENT File claim with shipping company prior to installation if shipmentis damaged or incomplete. Locate unit rating plate on unit servicepanel. It contains information needed to properly install unit.Check rating plate to be sure unit matches job specifications. Step 2—Install on a Soli...
4. Position sensing bulb on horizontal portion of suction tube adapter. Secure using supplied hardware. 5. Insulate bulb after installation. (See Fig. 5.) 6. Leak check all connections. FAN COILS If indoor unit (fan coil) comes factory equipped with a bi-flowhard shutoff TXV, no TXV change is requir...
SWEAT CONNECTION To avoid valve damage while brazing, service valves must bewrapped in a heat-sinking material such as a wet cloth. 1. Remove plastic retainer holding outdoor piston in liquid service valve. 2. Locate adapter tube shipped with unit. 3. Install strainer in adapter tube and connect tub...
