Carrier 30 GA- User Manual

Carrier 30 GA

Carrier 30 GA– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
Page: / 24

Table of Contents:

  • Page 2 – CONTENTS; Page
  • Page 3 – Safety device setting:; NOTE: Please fill in this sheet during the installation
  • Page 4 – Dimensions and clearances (standard unit)
  • Page 6 – Dimensions and clearances (unit with optional Hydroflow kit)
  • Page 10 – Bad; Good
  • Page 11 – APPLICATION DATA (UNIT WITH OPTIONAL HYDRONIC KIT); Available static pressure; Available static pressure for a single pump
  • Page 12 – use correctly sized piping.; Water loop volume
  • Page 13 – Follow all safety codes.; Preliminary checks; The surface must be horizontal, flat and intact.
  • Page 14 – Water connections; Note the water inlets and outlets of the heat exchangers.; Allowable load (Nm) for brazed plate heat exchangers; The illustration below shows a typical hydraulic circuit.; Typical hydraulic circuit diagram
  • Page 15 – C. It is recommended to protect the chilled water pipes that
  • Page 16 – Set point adjustment; Confirm that there are no refrigerant leaks.; Checks before start-up at the optional hydronic kit; Please refer to the controls manual for the unit.; Electromechanical control
  • Page 17 – SERVICING REFRIGERATION COMPONENTS; Servicing must be done by a qualified refrigeration engineer.; General maintenance; Leaks must be repaired immediately; Recharging liquid refrigerant; After detection and repair the unit can be recharged.
  • Page 18 – Compressor motor protection
  • Page 19 – Heat exchangers; the insulating foam is intact and securely in place.; Cleaning in place; Soldering instructions; C under normal soldering conditions; Condenser coil; Clean the coil with the appropriate cleaning agents.; . This process can either be carried out with a
  • Page 20 – Remove the grille with its support air duct assembly.; Fan motor protection
  • Page 22 – SYMPTOMS; Pump will not start; CAUSE; Flow controller open; REMEDY; Replace control component at fault; TROUBLESHOOTING CHART - HYDRAULIC KIT OPTION
Loading the manual

1

30GH/GZ 009-035

Air-Cooled Liquid Chillers

50 Hz

Installation, Operation and Maintenance Instructions

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - CONTENTS; Page

CONTENTS Page Start-up checklist .......................................................................................................................................................................... 3 Dimensions/clearances (standard unit) ...........................................................

Page 3 - Safety device setting:; NOTE: Please fill in this sheet during the installation

START-UP CHECK LIST Start-up date: Equipment sold by: Contract No.: Installed by: Contract No.: Site address: Start-up date: Equipment type and serial number: 30GH/GZ Electrical data: Supply voltage: Ph. V Ph. 2 V Ph. 3 V Nominal voltage: V % network voltage: Current draw: Ph. 1 A Ph. 2 A Ph. 3 A Co...

Page 4 - Dimensions and clearances (standard unit)

4 Dimensions and clearances (standard unit) 30GH/GZ A B C D E F G 009-013 1160 1220 1060 1200 1000 1000 1000 015-025 1720 1160 1112 1200 1000 1000 1000 030-035 2060 1370 1231 1200 1000 1000 1200 All dimensions are given in mm. Legend: Required service clearance Power supply Water inlet Water outlet ...

Other Carrier Models