Page 2 - User Commands; ii; Table of Contents
WUX450 / WX520 / WUX400ST / WX450ST User Commands - - ii Table of Contents Table of Contents ........................................................................................................ ii 1. Overview ..........................................................................................
Page 3 - iii
WUX450 / WX520 / WUX400ST / WX450ST User Commands - - iii BLANK ................................................................................................................................................. 26 BRI ......................................................................................
Page 5 - Communication Specifications; SD
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 2 - 2. Communication Specifications Communication Specifications The projector can be controlled via RS-232C or LAN connection. PC - Projector connection configuration RS-232C connection LAN connection Item Specifications Item Specifications Connec...
Page 6 - Usable Character Codes
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 3 - Usable Character Codes Use ASCII codes in the red and blue areas of below table. No distinction is made between double-byte characters and single-byte characters. Do not use double-byte or triple-byte characters. They will all be recognized as ...
Page 7 - Command Format; Format
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 4 - Communication System (Serial) Item Specifications Communication system RS-232-C Start-stop synchronization Semi-duplex communication Transmission speed 19.2 Kbps Character length 8 bits / character Stop bit 2 bits Parity None Command format Var...
Page 8 - Response Format; Normal response
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 5 - Response Format Responses are sent from the projector to PC in the following format: <Response character string> <Delimiter> There are multiple response types, each having different <response string> format. <Response chara...
Page 10 - Other; Command recognition
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 7 - Normal response (BUSY) This response is sent when a command cannot be received during processing. Format) i:BUSY<delimiter> Example) PC to PJ A U T O P C CR 41h 55h 54h 4Fh 50h 43h 0Dh PJ to PC i : B U S Y CR 69h 3Ah 42h 55h 53h 59h 0Dh O...
Page 11 - Communication Flow; Response Reception Timeout
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 8 - 3. Communication Flow Command Transmission (PC side) Commands should be sent from PC in a way that each character is sent within the specified Tc (inter-character timeout) Command Reception (projector side) The receiver (projector) retains inco...
Page 14 - Guide to command description; EXAMPLE
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 11 - 5. Guide to command description This section explains how commands are described. The command descriptions have the format shown below. EXAMPLE Summary of the function Format Setting Command A command format when a command is sent to the proje...
Page 15 - Remarks; Example
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 12 - Environment This defines the environments that support the command (power supply state, input signal state). The command is executable when the projector is in the mode indicated by " ○ " in the table of corresponding command descripti...
Page 16 - AXADJ
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 13 - 6. Command Details 6AXADJ 6-axix adjustment / OFF Format Setting Command 6AXADJ=<6-axix adjustment parameter: ID> Response i:OK Reference Command GET=6AXADJ Response g:6AXADJ=<6-axix adjustment parameter: ID> Note: See "Error l...
Page 23 - AMBADJ; AMBLEVEL
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 20 - AMBADJ Ambient light adjustment / OFF Format Setting Command AMBADJ=<Ambient light correction adjustment parameter:ID> Response i:OK Reference Command GET=AMBADJ Response g:AMBADJ=<Ambient light correction adjustment parameter:ID> ...
Page 24 - AMBTYPE; ASELA1
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 21 - AMBTYPE Ambient light type setting Format Setting Command AMBTYPE=<Ambient light type settings parameter:ID> Response i:OK Reference Command GET=AMBTYPE Response g:AMBTYPE=<Ambient light type settings parameter:ID> Note: See "E...
Page 25 - ASELA2; ASELC
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 22 - ASELA2 Analog PC-2 Audio input terminal selection Format Setting Command ASELA2=<Analog PC-2 audio terminal selection parameter: ID> Response i:OK Reference Command GET=ASELA2 Response g:ASELA2=<Analog PC-2 audio terminal selection pa...
Page 26 - ASELD; ASELH
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 23 - ASELD Digital PC Audio input terminal selection Format Setting Command ASELD=<Digital PC audio terminal selection parameter: ID> Response i:OK Reference Command GET=ASELD Response g:ASELD=<Digital PC audio terminal selection parameter...
Page 27 - ASPECT; AUTOPC
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 24 - ASPECT Aspect ratio Format Setting Command ASPECT=<Screen setting parameters: ID> Response i:OK Reference Command GET=ASPECT Response g:ASPECT=<Screen setting parameters: ID> Note: See "Error list" for any response other th...
Page 28 - AUTOSETEXE; AVOL
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 25 - AUTOSETEXE Auto setup Format Setting Command AUTOSETEXE=<Auto set parameter:ID> Response i:OK Reference Command - Response - Note: See "Error list" for any response other than the above. < Auto set parameter:ID > Parameter ...
Page 29 - BLANK; BRI
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 26 - BLANK BLANK setting Format Setting Command BLANK=<BLANK parameter:ID> Response i:OK Reference Command GET=BLANK Response g:BLANK=<BLANK parameter:ID> Note: See "Error list" for any response other than the above. < BLANK ...
Page 30 - COMVER
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 27 - COLOR_TEMP Color temperature Format Setting Command COLOR_TEMP=<Color temperature setting:Number> Response i:OK Reference Command GET=COLOR_TEMP Response g:COLOR_TEMP=<Color temperature setting:Number> Note: See "Error list"...
Page 31 - CONT; DGAMMA
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 28 - CONT Contrast Format Setting Command CONT=<Contrast setting:Number> Response i:OK Reference Command GET=CONT Response g:COMVER="<User command version:Character string> Note: See "Error list" for any response other than ...
Page 34 - ERR
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 31 - ERR Error information reference Format Setting Command - Response - Reference Command GET=ERR Response g:ERR=<ErrorID:Character string> Note: See "Error list" for any response other than the above. < DZOOM ratio parameter:ID &...
Page 38 - FLTWRN; Environment
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 35 - FLTWRN Air filter cleaning warning Format Setting Command FLTWRN=<Filter warning parameter: ID> Response i:OK Reference Command GET=FLTWRN Response g: FLTWRN=<Filter warning parameter: ID> Note: See "Error list" for any res...
Page 39 - GAMMA
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 36 - GAMMA Gamma adjustment Format Setting Command GAMMA=<Gamma adjustment:Number> Response i:OK Reference Command GET=GAMMA Response g: GAMMA=<Gamma adjustment:Number> Note: See "Error list" for any response other than the abov...
Page 40 - HUE
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 37 - HDMI_OVSCAN HDMI overscan setting Format Setting Command HDMI_OVSCAN=<HDMI overscan setting parameter:ID> Response i:OK Reference Command GET= HDMI_OVSCAN Response g: HDMI_OVSCAN=<HDMI overscan setting parameter:ID> Note: See "...
Page 41 - IMAGE
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 38 - IMAGE Image mode setting Format Setting Command IMAGE=<Image mode setting parameter:ID> Response i:OK Reference Command GET= IMAGE Response g: IMAGE=<Image mode setting parameter:ID> Note: See "Error list" for any response ...
Page 42 - IMAGEFLIP; INPUT
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 39 - IMAGEFLIP Flip display Format Setting Command IMAGEFLIP=<Image flip setting parameters:ID> Response i:OK Reference Command GET=IMAGEFLIP Response g:IMAGEFLIP=<Image flip setting parameters:ID> Note: See "Error list" for any...
Page 43 - KREP; LAMP
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 40 - KREP Key repeat Format Setting Command KREP=<Key repeat parameter: ID> Response i:OK Reference Command GET=KREP Response g:KREP=<Key repeat parameter: ID> Note: See "Error list" for any response other than the above. < K...
Page 44 - LAMPCOUNTER; LMPWRN
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 41 - LAMPCOUNTER Lamp counter reference Format Setting Command - Response - Reference Command GET=LAMPCOUNTER Response g:LAMPCOUNTER="<Lamp ON time:Character string> Note: See "Error list" for any response other than the above. &l...
Page 45 - MAIN
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 42 - MAIN Unit control panel emulation Format Setting Command MAIN=<Side control emulation button parameters:ID> Response i:OK Reference Command - Response - Note: See "Error list" for any response other than the above. < Side cont...
Page 46 - MEMF
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 43 - MEMF Memory color adjustment (flesh) Format Setting Command MEMF=<Memory color adjustment parameter:ID> Response i:OK Reference Command GET=MEMF Response g:MEMF=<Memory color adjustment parameter:ID> Note: See "Error list" ...
Page 47 - MEMS
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 44 - MEMS Memory color adjustment (sky) Format Setting Command MEMS=<Memory color adjustment parameter:ID> Response i:OK Reference Command GET=MEMS Response g:MEMS=<Memory color adjustment parameter:ID> Note: See "Error list" fo...
Page 49 - POWER
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 46 - POWER This controls the power supply Format Setting Command POWER=<power control parameter:ID> Response i:OK Reference Command GET=POWER Response g:POWER=<power mode parameter:ID> Note: See "Error list" for any response oth...
Page 50 - PRODCODE
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 47 - PRODCODE Product name inquiry Format Setting Command - Response - Reference Command GET=PRODCODE Response g:PRODCODE="<Product name:Character string> Note: See "Error list" for any response other than the above. < Product ...
Page 51 - RC
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 48 - RC Remote control operation emulate Format Setting Command RC=<Remote control emulation button parameters:ID> Response i:OK Reference Command - Response - Note: See "Error list" for any response other than the above. < Remote ...
Page 53 - RGBGAIN; RGBOFFSET
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 50 - RGBGAIN RGB gain adjustment Format Setting Command RGBGAIN=<R gain setting:Number>,<G gain setting:Number>, <B gain setting:Number> Response i:OK Reference Command GET=RGBGAIN Response g:RGBGAIN=<R gain setting:Number>,...
Page 54 - ROMVER; SAT
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 51 - ROMVER Firmware version inquiry Format Setting Command - Response - Reference Command GET=ROMVER Response g:ROMVER="<ROM version:Character string> Note: See "Error list" for any response other than the above. Environment Powe...
Page 55 - SAVEIMGPROF
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 52 - SAVEIMGPROF User memory creation/storage/deletion -- user memory creation status Format Setting Command SAVEIMGPROF=<User memory save to parameter:ID> Response i:OK Reference Command GET=SAVEIMGPROF Response g:SAVEIMGPROF=<Number of u...
Page 56 - SCRNASPECT; SHARP
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 53 - SCRNASPECT Screen aspect setting Format Setting Command SCRNASPECT=<Screen aspect setting parameter:ID> Response i:OK Reference Command GET=SCRNASPECT Response g:SCRNASPECT=<Screen aspect setting parameter:ID> Note: See "Error ...
Page 57 - SIGNALSTATUS
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 54 - SIGNAL_INFO Inquires about displayed signal information Format Setting Command - Response - Reference Command GET=SIGNAL_INFO Response g:SIGNAL_INFO="<Input signal information:Character string> Note: See "Error list" for any ...
Page 58 - TEMP
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 55 - TEMP Temperature sensor value inquiry Format Setting Command - Response - Reference Command GET=TEMP Response g: TEMP=<Number of sensors>,<Sensor 1 value>,…,<Sensor n value> Note: See "Error list" for any response oth...
Page 59 - TPTN
WUX450 / WX520 / WUX400ST / WX450ST User Commands - 56 - TPTN Test pattern Format Setting Command TPTN=<Test pattern parameter: ID> Response i:OK Reference Command GET=TPTN Response g:TPTN=<Test pattern parameter: ID> Note: See "Error list" for any response other than the above. ...
