Canon SX 50- User Manual

Page 2 - Projector User Commands; Revision History

Projector User Commands - - i Revision History Numerical value Date Page(s) Changes Revised by 01.0222/01 11/13/2009 --- First release 01.0222/02 11/19/2009 --- 01.0222/03 11/26/2009 --- 01.0222/04 12/04/2009 --- 01.0222/05 02/02/2010 ---

Page 3 - ii; Table of Contents

Projector User Commands - - ii Table of Contents Revision History.................................................................................................................................................................. i 1. Overview .............................................................

Page 4 - iii

Projector User Commands - - iii DVRANGE ................................................................................................................................................ 40 FCONTDRV ..........................................................................................................

Page 5 - iv

Projector User Commands - - iv GET LAMP ............................................................................................................................................. 139 GET LAMPCOUNTER .....................................................................................................

Page 8 - Communication Specifications

Projector User Commands - 2 - Revision History / Date Changes Revised by Approved by 2. Communication Specifications Communication Specifications PC - Projector connection status Item Specifications Connection system PC and projector connected on a "1:1" basis Connection signal line 3-line c...

Page 9 - Communication System

Projector User Commands - 3 - Revision History / Date Changes Revised by Approved by Communication System Item Specifications Communication system RS-232-C Start-stop synchronization Semi-duplex communication Transmission speed 19.2 Kbps Character length 8 bits/character Stop bit 2 bits Parity None ...

Page 10 - Communication system; Transmission format

Projector User Commands - 4 - Revision History / Date Changes Revised by Approved by Communication system Communication between the PC and projector is performed by the projector responding by sending a response to the command sent from the PC. If AC power is supplied to the projector, communication...

Page 11 - Response; Transmissionformat

Projector User Commands - 5 - Revision History / Date Changes Revised by Approved by Response Transmissions sent from Projector to PC in response to commands from PC. Transmissionformat <Response character string> <Delimiter> <Response character string> Character strings consisting...

Page 12 - Other; Transmission recognition; Cable

Projector User Commands - 6 - Revision History / Date Changes Revised by Approved by Example: > RANGE CONT < r:CONT=N, -20, 20 Other Transmission recognition Transmission is recognized when delimiter is received. Even if a maximum transmission length is received, the entire received transmissi...

Page 13 - Communication Flow; Transmission sent

Projector User Commands - 7 - Revision History / Date Changes Revised by Approved by 3. Communication Flow Transmission sent At the sending side (PC), the transmission is sent within character intervals of Tc (character interval timeout). Transmission received At the receiving side (Projector), data...

Page 15 - SX7 Mark II User Command System

Projector User Commands - 9 - Revision History / Date Changes Revised by Approved by SX7 Mark II User Command System Switch to Remote modeSwitch to Local mode Display setting Input select Total number of dots adjustment Input signal settings Tracking adjustmentHorizontal/Vertical position adjustment...

Page 20 - Power Management Mode

Projector User Commands - 14 - Revision History / Date Changes Revised by Approved by 7. Power Management Mode Concerning the processing for switching to the power management standby or exit mode in the remote or local mode. Mode SX50 SX6/SX60/X600/SX7/X700/SX7 Mark II Remote The power management st...

Page 23 - Details of Command; Alphabetic command name; This briefly describes the command function.

Projector User Commands - 17 - Revision History / Date Changes Revised by Approved by 9. Details of Command Descriptions of each command are provided starting from the next page. The command descriptions have the format shown below. Alphabetic command name This briefly describes the command function...

Page 24 - AXADJ

Projector User Commands - 18 - Revision History / Date Changes Revised by Approved by 6AXADJ 6-axis adjustment ON/OFF Format 6AXADJ=<6-axis adjustment parameter:ID> Parameter <6-axis adjustment parameter:ID> ON This sets the 6-axis adjustment to ON. OFF This sets the 6-axis adjustment to...

Page 27 - ACADJUST; Advanced color adjustment

Projector User Commands - 21 - Revision History / Date Changes Revised by Approved by ACADJUST Advanced color adjustment Format ACADJUST=<Advanced color adjustment parameter:ID> Parameter <Advanced color adjustment parameter:ID> NOCORRECT No adjustment MEM_L Low memory color adjustment M...

Page 29 - ASPECT; Screen settings

Projector User Commands - 23 - Revision History / Date Changes Revised by Approved by ASPECT Screen settings Format ASPECT=<Screen setting parameters:ID> Parameter <Screen setting parameters:ID> Errors supported by model Parameter Meaning SX50 SX6, SX60, X600 SX7, X700 SX7 Mark II AUTO A...

Page 31 - Auto PC

Projector User Commands - 25 - Revision History / Date Changes Revised by Approved by AUTOPC Auto PC Format AUTOPC Response "i:OK" is returned if the control was executed properly. For details on other responses, refer to the "Error List". Description This executes Auto PC. (1) For m...

Page 32 - Auto setup

Projector User Commands - 26 - Revision History / Date Changes Revised by Approved by AUTOSETEXE Auto setup Format AUTOSETEXE □ <Auto set parameter:ID> Parameter <Auto set parameter:ID> FOCUS Auto focusing VKS Auto keystone (vertical) execution SCRN Automatic screen color correction exec...

Page 34 - AVOL; Audio volume adjustment

Projector User Commands - 28 - Revision History / Date Changes Revised by Approved by AVOL Audio volume adjustment Format AVOL=<Audio volume level:Number> Parameter <Audio volume level:Number> Audio volume level 0 to 20 The RANGE command can be used to obtain the parameter range that can...

Page 36 - BLANK; BLANK function

Projector User Commands - 30 - Revision History / Date Changes Revised by Approved by BLANK BLANK function Format BLANK=<BLANK parameter:ID> Parameter <BLANK parameter:ID> ON BLANK ON OFF BLANK OFF The parameters which can be set at any given point in time can be obtained using the RANGE...

Page 38 - BRI; Brightness setting

Projector User Commands - 32 - Revision History / Date Changes Revised by Approved by BRI Brightness setting Format BRI=<Brightness setting:Number> Parameter <Brightness setting:Number> Brightness setting -20 to 20 The parameters which can be set at any given point in time can be obtaine...

Page 39 - BVOL; BEEP sound setting

Projector User Commands - 33 - Revision History / Date Changes Revised by Approved by BVOL BEEP sound setting Format BVOL=<Beep sound setting:Number> Parameter <Beep sound setting:Number> 0 BEEP sound mute 1 BEEP sound output The parameters which can be set at any given point in time can...

Page 40 - CONT; Contrast setting

Projector User Commands - 34 - Revision History / Date Changes Revised by Approved by CONT Contrast setting Format CONT=<Contrast setting:Number> Parameter <Contrast setting:Number> Contrast setting -20 to 20 The parameters which can be set at any given point in time can be obtained usin...

Page 41 - DGAMMA; Dynamic gamma

Projector User Commands - 35 - Revision History / Date Changes Revised by Approved by DGAMMA Dynamic gamma Format DGAMMA=<Dynamic gamma setting parameter:ID> Parameter <Dynamic gamma setting parameter:ID> 0 OFF 1 ON The parameters which can be set at any given point in time can be obtain...

Page 43 - DOTS; Total number of dots adjustment

Projector User Commands - 37 - Revision History / Date Changes Revised by Approved by DOTS Total number of dots adjustment Format DOTS=<Number of dots:Number> Parameter <Number of dots:Number> Number of dots The RANGE command can be used to obtain the parameter range that can be set at t...

Page 45 - DPON; Direct power-on setting

Projector User Commands - 39 - Revision History / Date Changes Revised by Approved by DPON Direct power-on setting Format DPON=<Direct power-on setting parameter:ID> Parameter <Direct power-on setting parameter:ID> ON This sets direct power-on to ON. OFF This sets direct power-on to OFF....

Page 46 - DVRANGE; Digital video setting

Projector User Commands - 40 - Revision History / Date Changes Revised by Approved by DVRANGE Digital video setting Format DVRANGE=<Digital video setting parameter:ID> Parameter <Digital video setting parameter:ID> FULL Displays digital signals at full range. LIMITED Displays digital sig...

Page 47 - FCONTDRV; Focus lens continuous drive control

Projector User Commands - 41 - Revision History / Date Changes Revised by Approved by FCONTDRV Focus lens continuous drive control Format FCONTDRV=<Focus lens continuous control parameter:ID> Parameter <Focus lens continuous control parameter:ID> STOP This stops the focusing. FAR This in...

Page 49 - FSTEPDRV; Focus lens step drive control

Projector User Commands - 43 - Revision History / Date Changes Revised by Approved by FSTEPDRV Focus lens step drive control Format FSTEPDRV=<Focus lens step control parameter:ID> Parameter <Focus lens step control parameter:ID> FAR This initiates focusing toward the far end. NEAR This i...

Page 50 - GAMMA; Gamma adjustment

Projector User Commands - 44 - Revision History / Date Changes Revised by Approved by GAMMA Gamma adjustment Format GAMMA=<Gamma adjustment:Number> Parameter <Gamma adjustment:Number> Other than SX7 Mark II -4 to 4 each value SX7 Mark II -10 to 10 each value The parameters which can be s...

Page 51 - GUIDE; Guide setting

Projector User Commands - 45 - Revision History / Date Changes Revised by Approved by GUIDE Guide setting Format GUIDE=<Guide setting parameter:ID> Parameter <Guide setting parameter:ID> ON Guide display ON OFF Guide display OFF The parameters which can be set at any given point in time ...

Page 52 - Horizontal/Vertical resolution adjustment

Projector User Commands - 46 - Revision History / Date Changes Revised by Approved by HPIX/VPIX Horizontal/Vertical resolution adjustment Format HPIX=<Horizontal resolution:Number> VPIX=<Vertical resolution:Number> Parameter <Horizontal resolution:Number> <Vertical resolution:Nu...

Page 54 - Horizontal/Vertical position adjustment

Projector User Commands - 48 - Revision History / Date Changes Revised by Approved by HPOS/VPOS Horizontal/Vertical position adjustment Format HPOS=<Horizontal position:Number> VPOS=<Vertical position:Number> Parameter <Horizontal position:Number> VPOS=<Vertical position:Number&...

Page 56 - HUE; Hue setting

Projector User Commands - 50 - Revision History / Date Changes Revised by Approved by HUE Hue setting Format HUE=<Hue setting value:Number> Parameter <Hue setting value:Number> Hue setting -20 to 20 The parameters which can be set at any given point in time can be obtained using the RANG...

Page 58 - IMAGE; Image mode setting; Format

Projector User Commands - 52 - Revision History / Date Changes Revised by Approved by IMAGE Image mode setting Format IMAGE=<Image mode setting parameter:ID> Parameter <Image mode setting parameter:ID> Errors supported by model Parameter Meaning SX50 SX6, SX7 SX60 X600 SX7 Mark II SX7 Ma...

Page 59 - Commands supported

Projector User Commands - 53 - Revision History / Date Changes Revised by Approved by Example Setting > IMAGE=PRESENTATION This sets the image mode to "Presentation". < i:OK Reference > GET IMAGE or ?IMAGE This references the current image mode. < g:IMAGE=CINEMA Acquisition of pa...

Page 60 - IMAGEFLIP; Flip display

Projector User Commands - 54 - Revision History / Date Changes Revised by Approved by IMAGEFLIP Flip display Format IMAGEFLIP=<Image flip setting parameters:ID> Parameter <Image flip setting parameters:ID> Parameter Meaning Remarks NONE None CEILING Ceiling Flip horizontally REAR Rear Fl...

Page 62 - INPUT; Input selection

Projector User Commands - 56 - Revision History / Date Changes Revised by Approved by INPUT Input selection Format INPUT=<Input selection parameters:ID> Parameter <Input selection parameters:ID> Errors supported by model Parameter Meaning SX50 SX6, SX60, X600 SX7, X700 SX7 Mark II D-RGB ...

Page 64 - KEYLOCK; Keylock setting

Projector User Commands - 58 - Revision History / Date Changes Revised by Approved by KEYLOCK Keylock setting Format KEYLOCK=<Key lock setting parameters:ID> Parameter <Key lock setting parameters:ID> OFF No locking (OFF) MAIN Main key lock RC Remote control key lock The parameters which...

Page 66 - Lamp output setting

Projector User Commands - 60 - Revision History / Date Changes Revised by Approved by LAMP Lamp output setting Format LAMP=<Lamp output setting parameters:ID> Parameter <Lamp output setting parameters:ID> NORMAL Normal SILENT Silent cooling The parameters which can be set at any given po...

Page 67 - LANG; Language select

Projector User Commands - 61 - Revision History / Date Changes Revised by Approved by LANG Language select Format LANG=<Language selection parameters:ID> Parameter <Language selection parameters:ID> Errors supported by model Parameter Meaning SX50 SX6, SX60, X600 SX7, X700 SX7 Mark II EN...

Page 69 - LEDILLUMINATE; Emotional LED and signal sensing LED lighting control

Projector User Commands - 63 - Revision History / Date Changes Revised by Approved by LEDILLUMINATE Emotional LED and signal sensing LED lighting control Format LEDILLUMINATE=<LED lighting control setting parameter:ID> Parameter <LED lighting control setting parameter:ID> ON This sets th...

Page 70 - Switch to local mode; Example

Projector User Commands - 64 - Revision History / Date Changes Revised by Approved by LOCAL Switch to local mode Format LOCAL Response "i:OK" is returned when it was possible to switch the mode properly. For details on other responses, refer to the "Error List". Description This swit...

Page 72 - LOGOPOS; User image position setting

Projector User Commands - 66 - Revision History / Date Changes Revised by Approved by LOGOPOS User image position setting Format LOGOPOS=<User image position setting parameters : ID> Parameter <User image position setting parameters:ID> UPPER_L Upper left UPPER_R Upper right CENTER Cente...

Page 74 - Front panel operation emulation; Parameter

Projector User Commands - 68 - Revision History / Date Changes Revised by Approved by MAIN Front panel operation emulation Format MAIN □ <Main unit panel emulation button parameters:ID> Parameter <Main unit panel emulation button parameters:ID> Errors supported by model Parameter Meaning...

Page 76 - MEMCADJ; Memory color adjustment

Projector User Commands - 70 - Revision History / Date Changes Revised by Approved by MEMCADJ Memory color adjustment Format MEMCADJ=<Memory color adjustment parameter:ID> Parameter <Memory color adjustment parameter:ID> OFF No adjustment MEM_L Memory color adjustment - light MEM_M Memor...

Page 78 - MUTE; Mute control

Projector User Commands - 72 - Revision History / Date Changes Revised by Approved by MUTE Mute control Format MUTE=<Mute control parameter: ID> Parameter <Mute control parameter: ID> ON This turns off the audio/beep sound. OFF This returns the audio/beep sound to its original setting. T...

Page 79 - NOSHOW; Display screen setting when nothing shown

Projector User Commands - 73 - Revision History / Date Changes Revised by Approved by NOSHOW Display screen setting when nothing shown Format NOSHOW=<Parameters for setting display screen in no show status:ID> Parameter <Parameters for setting display screen in no show status:ID> For mod...

Page 81 - NOSIG; Display screen when no signal setting

Projector User Commands - 75 - Revision History / Date Changes Revised by Approved by NOSIG Display screen when no signal setting Format NOSIG=<Parameters for setting display screen in no-signal mode:ID> Parameter <Parameters for setting display screen in no-signal mode:ID> For models ot...

Page 83 - PJON; Display screen at startup setting

Projector User Commands - 77 - Revision History / Date Changes Revised by Approved by PJON Display screen at startup setting Format PJON=<Parameters for setting display screen at startup:ID> Parameter <Parameters for setting display screen at startup:ID> For models other than SX7 Mark II...

Page 85 - PMM; Power management

Projector User Commands - 79 - Revision History / Date Changes Revised by Approved by PMM Power management Format PMM=<Power management setting parameters:ID> Parameter <Power management setting parameters:ID> OFF OFF STANDBY Standby mode EXIT Exit mode The parameters which can be set at...

Page 87 - This controls the power supply

Projector User Commands - 81 - Revision History / Date Changes Revised by Approved by POWER This controls the power supply Format POWER □ <Parameter:ID> Parameter <Parameter:ID> For SX50, SX6, SX60, X600, SX7, X700 ON Power ON OFF Power OFF For SX7 Mark II ON Power ON OFF Power OFF BLKON...

Page 89 - PROG; Progressive setting

Projector User Commands - 83 - Revision History / Date Changes Revised by Approved by PROG Progressive setting Format PROG=<Progressive conversion setting parameters:ID> Parameter <Progressive conversion setting parameters:ID> Errors supported by model Parameter Meaning SX50 SX6, SX60, X...

Page 91 - Remote control operation emulate

Projector User Commands - 85 - Revision History / Date Changes Revised by Approved by RC Remote control operation emulate Format RC □ <Remote control emulation button parameters:ID> Parameter <Remote control emulation button parameters:ID> Errors supported by model Parameter Meaning SX50...

Page 93 - RCCH; Remote control channel setting

Projector User Commands - 87 - Revision History / Date Changes Revised by Approved by RCCH Remote control channel setting Format RCCH=<Remote control setting parameters:ID> Parameter <Remote control setting parameters:ID> 1 Remote control channel 1 2 Remote control channel 2 The paramete...

Page 94 - Switch to Remote mode

Projector User Commands - 88 - Revision History / Date Changes Revised by Approved by REMOTE Switch to Remote mode Format REMOTE Response "i:OK" is returned mode was switched properly. For details on other responses, refer to the "Error List". Description This switches to Remote mode...

Page 95 - Reset

Projector User Commands - 89 - Revision History / Date Changes Revised by Approved by RESET Reset Format RESET □ <Reset parameters:ID> Parameter <Reset parameters:ID> LAMPTIME Lamp on time reset IMAGE Current image adjustment reset SYSTEM Initial system settings(same as "Factory sett...

Page 97 - RGBGAIN; RGB gain adjustment

Projector User Commands - 91 - Revision History / Date Changes Revised by Approved by RGBGAIN RGB gain adjustment Format RGBGAIN=<R gain setting:Number> ▽ <G gain setting:Number> ▽ <B gain setting:Number> Parameter <R gain setting:Number> ▽ <G gain setting:Number> ▽ <...

Page 98 - RGBOFFSET; RGB offset adjustment

Projector User Commands - 92 - Revision History / Date Changes Revised by Approved by RGBOFFSET RGB offset adjustment Format RGBOFFSET=<R offset setting:Number> ▽ <G offset setting:Number> ▽ <B offset setting:Number> Parameter <R offset setting:Number> ▽ <G offset setting:...

Page 100 - SAT; Color saturation setting

Projector User Commands - 94 - Revision History / Date Changes Revised by Approved by SAT Color saturation setting Format SAT=<Color saturation value setting: Number> Parameter <Color saturation value setting: Number> Saturation setting -20 to 20 The parameters which can be set at any gi...

Page 102 - Screen aspect setting

Projector User Commands - 96 - Revision History / Date Changes Revised by Approved by SCRNASPECT Screen aspect setting Format SCRNASPECT=<Screen aspect setting parameter:ID> Parameter <Screen aspect setting parameter:ID> 4:3 4:3 display 16:9 16:9 display 16:9_DIS 16:9 Digital Image Shift...

Page 103 - SEL; Input signal selection

Projector User Commands - 97 - Revision History / Date Changes Revised by Approved by SEL Input signal selection Format SEL=<Input signal selection parameter:ID> Parameter <Input signal selection parameter:ID> AUTO Auto The parameters which can be set at any given point in time can be ob...

Page 105 - SHARP; Sharpness setting

Projector User Commands - 99 - Revision History / Date Changes Revised by Approved by SHARP Sharpness setting Format SHARP=<Sharpness setting:Number> Parameter <Sharpness setting:Number> Sharpness setting -4 to 4 The parameters which can be set at any given point in time can be obtained ...

Page 106 - TERMINAL; Terminal setting

Projector User Commands - 100 - Revision History / Date Changes Revised by Approved by TERMINAL Terminal setting Format TERMINAL=<Terminal setting parameters:ID> Parameter <Terminal setting parameters:ID> IN This sets to input OUT This sets to output The parameters which can be set at an...

Page 107 - TRACK; Tracking adjustment

Projector User Commands - 101 - Revision History / Date Changes Revised by Approved by TRACK Tracking adjustment Format TRACK=<Adjustment value:Number> Parameter <Adjustment value:Number> The parameters which can be set at any given point in time can be obtained using the RANGE command. ...

Page 108 - VDISHIFT; Vertical digital image shift setting

Projector User Commands - 102 - Revision History / Date Changes Revised by Approved by VDISHIFT Vertical digital image shift setting Format VDISHIFT=<Vertical shift amount:Number> Parameter <Vertical shift amount:Number> Vertical shift amount -131 to 131 The shift amount which can be set...

Page 109 - Vertical/horizontal keystone setting

Projector User Commands - 103 - Revision History / Date Changes Revised by Approved by VKS/HKS Vertical/horizontal keystone setting Format VKS=<Vertical keystone distortion value:Number> HKS=<Horizontal keystone distortion value:Number> Parameter <Vertical keystone distortion value:Nu...

Page 111 - WB; Screen color correction

Projector User Commands - 105 - Revision History / Date Changes Revised by Approved by WB Screen color correction Format WB=<Screen color correction parameters:ID> Parameter <Screen color correction parameters:ID> NORMAL Standard GREENBOARD Blackboard ADJUST Adjust The parameters which c...

Page 113 - WBRGB

Projector User Commands - 107 - Revision History / Date Changes Revised by Approved by WBRGB Screen color correction (ADJUST) Format WBRGB= <R adjustment value:Number> ▽ <G adjustment value:Number> ▽ <B adjustment value:Number> Parameter <R adjustment value:Number> ▽ <G ad...

Page 115 - ZCONTDRV; Zoom lens continuous drive control

Projector User Commands - 109 - Revision History / Date Changes Revised by Approved by ZCONTDRV Zoom lens continuous drive control Format ZCONTDRV=<Zoom lens continuous control parameter:ID> Parameter <Zoom lens continuous control parameter:ID> STOP This stops the zooming. WIDE This zoom...

Page 117 - ZSTEPDRV; Zoom lens step drive control

Projector User Commands - 111 - Revision History / Date Changes Revised by Approved by ZSTEPDRV Zoom lens step drive control Format ZSTEPDRV=<Zoom lens step control parameter:ID> Parameter <Zoom lens step control parameter:ID> WIDE This zooms to the wide-angle end. TELE This zooms to the...

Page 118 - Retrieve each data

Projector User Commands - 112 - Revision History / Date Changes Revised by Approved by GET Retrieve each data Format GET □ <Parameter> ? △ <Parameter> Parameter Parameter Meaning MODE Mode POWER Power supply state BLANK BLANK status INPUT Input state DOTS Total dot number TRACK Tracking ...

Page 121 - -axis correction R to Y hue/color saturation setting inquiry

Projector User Commands - 115 - Revision History / Date Changes Revised by Approved by GET 6AXR-6AXY 6-axis correction R to Y hue/color saturation setting inquiry Format R setting inquiry G setting inquiry B setting inquiry GET □ 6AXR GET □ 6AXG GET □ 6AXB ? △ 6AXR ? △ 6AXG ? △ 6AXB C setting inquir...

Page 122 - GET ACADJUST; Advanced color adjustment inquiry

Projector User Commands - 116 - Revision History / Date Changes Revised by Approved by GET ACADJUST Advanced color adjustment inquiry Format GET □ ACADJUST ? △ ACADJUST Response g:ACADJUST=<Details of adjustment:ID> <Details of adjustment:ID> NOCORRECT No adjustment MEM_L Low memory colo...

Page 123 - Screen setting inquiry

Projector User Commands - 117 - Revision History / Date Changes Revised by Approved by GET ASPECT Screen setting inquiry Format GET □ ASPECT ? △ ASPECT Response g:ASPECT=<Screen setting:ID> <Screen setting:ID> Errors supported by model Parameter Meaning SX50 SX6, SX60, X600 SX7, X700 SX7...

Page 124 - Audio volume setting inquiry

Projector User Commands - 118 - Revision History / Date Changes Revised by Approved by GET AVOL Audio volume setting inquiry Format GET □ AVOL ? △ AVOL Response g:AVOL=<Volume setting:Number> For details on other responses, refer to the "Error List". Description This command is used to...

Page 125 - GET BLANK; BLANK status inquiry

Projector User Commands - 119 - Revision History / Date Changes Revised by Approved by GET BLANK BLANK status inquiry Format GET □ BLANK ? △ BLANK Response g:BLANK=<BLANK status:ID> <BLANK status:ID> ON BLANK underway OFF BLANK release underway For details on other responses, refer to th...

Page 126 - Brightness value setting inquiry

Projector User Commands - 120 - Revision History / Date Changes Revised by Approved by GET BRI Brightness value setting inquiry Format GET □ BRI ? △ BRI Response g:BRI=<Brightness ： Number> For details on other responses, refer to the "Error List". Description This command is used to i...

Page 127 - Beep sound value setting inquiry

Projector User Commands - 121 - Revision History / Date Changes Revised by Approved by GET BVOL Beep sound value setting inquiry Format GET □ BVOL ? △ BVOL Response g:BVOL=<Setting ID> <Setting ID> 0 BEEP sound mute 1 BEEP sound output For details on other responses, refer to the "Er...

Page 128 - GET COMVER; User command version inquiry

Projector User Commands - 122 - Revision History / Date Changes Revised by Approved by GET COMVER User command version inquiry Format GET □ COMVER ? △ COMVER Response g:COMVER="<User command version ： Character string>" <User command version>:= 99.9999 For details on other respon...

Page 129 - Contrast value setting inquiry

Projector User Commands - 123 - Revision History / Date Changes Revised by Approved by GET CONT Contrast value setting inquiry Format GET □ CONT ? △ CONT Response g:CONT=<Contrast value:Number> For details on other responses, refer to the "Error List". Description This command is used ...

Page 130 - GET DGAMMA; Dynamic gamma value setting inquiry

Projector User Commands - 124 - Revision History / Date Changes Revised by Approved by GET DGAMMA Dynamic gamma value setting inquiry Format GET □ DGAMMA ? △ DGAMMA Response g:DGAMMA=<Setting:ID> <Setting:ID> 0 Off 1 On For details on other responses, refer to the "Error List". D...

Page 131 - Total number of dots inquiry

Projector User Commands - 125 - Revision History / Date Changes Revised by Approved by GET DOTS Total number of dots inquiry Format GET □ DOTS ? △ DOTS Response g:DOTS=<Total number of dots: Number> For details on other responses, refer to the "Error List". Description This command is ...

Page 132 - Direct power-on setting inquiry

Projector User Commands - 126 - Revision History / Date Changes Revised by Approved by GET DPON Direct power-on setting inquiry Format GET □ DPON ? △ DPON Response g:DPON=<Setting:ID> <Setting:ID> ON This sets direct power-on to ON. OFF This sets direct power-on to OFF. For details on ot...

Page 133 - GET DVRANGE; Digital video setting inquiry

Projector User Commands - 127 - Revision History / Date Changes Revised by Approved by GET DVRANGE Digital video setting inquiry Format GET □ DVRANGE ? △ DVRANGE Response g:DVRANGE=<Setting:ID> <Setting:ID> FULL Displays digital signals at full range. LIMITED Displays digital signals at ...

Page 134 - GET ERR; Error information inquiry

Projector User Commands - 128 - Revision History / Date Changes Revised by Approved by GET ERR Error information inquiry Format GET □ ERR ? △ ERR Response g:ERR=<Error ID:ID> <Error ID:ID> Errors supported by model Error ID Meaning SX50 SX6, SX60, X600 SX7, X700 SX7 Mark II NO_ERROR No e...

Page 135 - GET FREEZE; Freeze status inquiry

Projector User Commands - 129 - Revision History / Date Changes Revised by Approved by GET FREEZE Freeze status inquiry Format GET □ FREEZE ? △ FREEZE Response g:FREEZE=<Status:ID> <Status:ID> ON Image now frozen OFF Image now not frozen For details on other responses, refer to the "...

Page 136 - Gamma adjustment value inquiry

Projector User Commands - 130 - Revision History / Date Changes Revised by Approved by GET GAMMA Gamma adjustment value inquiry Format GET □ GAMMA ? △ GAMMA Response g:GAMMA=<Gamma adjustment value ： Number> For details on other responses, refer to the "Error List". Description This co...

Page 137 - GET GUIDE; Guide setting inquiry

Projector User Commands - 131 - Revision History / Date Changes Revised by Approved by GET GUIDE Guide setting inquiry Format GET □ GUIDE ? △ GUIDE Response g:GUIDE=<Setting:ID> <Setting:ID> ON Guide display ON OFF Guide display OFF For details on other responses, refer to the "Error...

Page 138 - Horizontal and vertical resolution inquiries

Projector User Commands - 132 - Revision History / Date Changes Revised by Approved by GET HPIX/VPIX Horizontal and vertical resolution inquiries Format Horizontal resolution inquiry Vertical resolution inquiry GET □ HPIX GET □ VPIX ? △ HPIX ? △ VPIX Response g:HPIX=<Horizontal resolution:Number&...

Page 139 - Horizontal and vertical position adjustment inquiries

Projector User Commands - 133 - Revision History / Date Changes Revised by Approved by GET HPOS/VPOS Horizontal and vertical position adjustment inquiries Format Horizontal position adjustment inquiry Vertical position adjustment inquiry GET □ HPOS GET □ VPOS ? △ HPOS ? △ VPOS Response g:HPOS=<Ho...

Page 140 - Hue value setting inquiry

Projector User Commands - 134 - Revision History / Date Changes Revised by Approved by GET HUE Hue value setting inquiry Format GET □ HUE ? △ HUE Response g:HUE=<Hue value setting ： Number> For details on other responses, refer to the "Error List". Description This command is used to i...

Page 141 - Image mode inquiry

Projector User Commands - 135 - Revision History / Date Changes Revised by Approved by GET IMAGE Image mode inquiry Format GET □ IMAGE ? △ IMAGE Response g:IMAGE=<Image mode:ID> <Image mode:ID> Errors supported by model Parameter Meaning SX50 SX6 SX60 X600 STANDARD Standard O O O O PRESE...

Page 142 - Flip display setting inquiry

Projector User Commands - 136 - Revision History / Date Changes Revised by Approved by GET IMAGEFLIP Flip display setting inquiry Format GET □ IMAGEFLIP ? △ IMAGEFLIP Response g:IMAGEFLIP=<Setting:ID> <Setting:ID> Parameter Meaning Remarks NONE None CEILING Ceiling Flip horizontally REAR...

Page 143 - Input selection inquiry

Projector User Commands - 137 - Revision History / Date Changes Revised by Approved by GET INPUT Input selection inquiry Format GET □ INPUT ? △ INPUT Response g:INPUT=<Input type:ID> <Input type:ID> Errors supported by model Input type Meaning SX50 SX6, SX60, X600 SX7, X700 SX7 Mark II D...

Page 144 - GET KEYLOCK; Key lock setting inquiry

Projector User Commands - 138 - Revision History / Date Changes Revised by Approved by GET KEYLOCK Key lock setting inquiry Format GET □ KEYLOCK ? △ KEYLOCK Response g:KEYLOCK=<Setting:ID> <Setting:ID> OFF No locking (OFF) MAIN Main key lock RC Remote control key lock For details on othe...

Page 145 - Lamp output setting inquiry

Projector User Commands - 139 - Revision History / Date Changes Revised by Approved by GET LAMP Lamp output setting inquiry Format GET □ LAMP ? □ LAMP Response g:LAMP=<Setting:ID> <Setting:ID> NORMAL Normal SILENT Silent cooling For details on other responses, refer to the "Error Lis...

Page 146 - Lamp ON time inquiry

Projector User Commands - 140 - Revision History / Date Changes Revised by Approved by GET LAMPCOUNTER Lamp ON time inquiry Format GET □ LAMPCOUNTER ? △ LAMPCOUNTER Response g:LAMPCOUNTER="<Lamp ON time: Character string>" <Lamp ON time: Character string> Meaning (ON time: H) Set...

Page 147 - Language inquiry

Projector User Commands - 141 - Revision History / Date Changes Revised by Approved by GET LANG Language inquiry Format GET □ LANG ? △ LANG Response g:LANG=<Language:ID> <Language:ID> Errors supported by model Parameter Meaning SX50 SX6, SX60, X600 SX7, X700 SX7 Mark II ENG English O O O...

Page 149 - GET LEDILLUMINATE; Emotional LED and signal sensing LED lighting setting inquiry

Projector User Commands - 143 - Revision History / Date Changes Revised by Approved by GET LEDILLUMINATE Emotional LED and signal sensing LED lighting setting inquiry Format GET □ LEDILLUMINATE ? △ LEDILLUMINATE Response g:LEDILLUMINATE=<Setting:ID> <Setting:ID> ON This sets the LED disp...

Page 150 - Lamp lighting time inquiry

Projector User Commands - 144 - Revision History / Date Changes Revised by Approved by GET LMPT Lamp lighting time inquiry Format GET □ LMPT ? △ LMPT Response g:LMPT=<Lighting time (hours):Number>:<Lighting time (minutes):Number> <Lighting time (hours):Number>:=Any 1 to 5-digit num...

Page 151 - GET LOGOPOS; User image position inquiry

Projector User Commands - 145 - Revision History / Date Changes Revised by Approved by GET LOGOPOS User image position inquiry Format GET □ LOGOPOS ? △ LOGOPOS Response g:LOGOPOS=<Setting:ID> <Setting:ID> UPPER_L Upper left UPPER_R Upper right CENTER Center LOWER_L Lower left LOWER_R Low...

Page 152 - GET MEMCADJ; Memory color adjustment setting inquiry

Projector User Commands - 146 - Revision History / Date Changes Revised by Approved by GET MEMCADJ Memory color adjustment setting inquiry Format GET □ MEMCADJ ? △ MEMCADJ Response g:MEMCADJ=<Details of adjustment:ID> <Details of adjustment:ID> OFF No adjustment MEM_L Memory color adjust...

Page 153 - GET MODE; Current control mode inquiry

Projector User Commands - 147 - Revision History / Date Changes Revised by Approved by GET MODE Current control mode inquiry Format GET □ MODE ? △ MODE Response g:MODE=<Mode:ID> <Mode:ID> LOCAL The local mode is currently established. REMOTE The remote mode is currently established. For ...

Page 154 - Mute control setting inquiry

Projector User Commands - 148 - Revision History / Date Changes Revised by Approved by GET MUTE Mute control setting inquiry Format GET □ MUTE ? △ MUTE Response g:MUTE=<Setting:ID> <Setting:ID> ON This turns off the audio/beep sound. OFF This returns the audio/beep sound to its original ...

Page 155 - GET NOSHOW; Display screen when nothing is shown setting inquiry

Projector User Commands - 149 - Revision History / Date Changes Revised by Approved by GET NOSHOW Display screen when nothing is shown setting inquiry Format GET □ NOSHOW ? △ NOSHOW Response g:NOSHOW=<Setting:ID> <Setting:ID> For models other than SX7 Mark II BLACK Black screen BLUE Blue...

Page 156 - GET NOSHOWSTATE; NoShow status inquiry

Projector User Commands - 150 - Revision History / Date Changes Revised by Approved by GET NOSHOWSTATE NoShow status inquiry Format GET □ NOSHOWSTATE ? △ NOSHOWSTATE Response g:NOSHOWSTATE=<Status:ID> <Status:ID> ON Screen temporarily off OFF Screen not temporarily off For details on oth...

Page 157 - GET NOSIG; Screen displayed at startup with no signals setting inquiry

Projector User Commands - 151 - Revision History / Date Changes Revised by Approved by GET NOSIG Screen displayed at startup with no signals setting inquiry Format GET □ NOSIG ? △ NOSIG Response g:NOSIG=<Setting:ID> <Setting:ID> For models other than SX7 Mark II BLACK Black screen BLUE B...

Page 158 - GET PJON; Screen displayed at startup setting inquiry

Projector User Commands - 152 - Revision History / Date Changes Revised by Approved by GET PJON Screen displayed at startup setting inquiry Format GET □ PJON ? △ PJON Response g:PJON=<Setting:ID> <Setting:ID> For models other than SX7 Mark II CANON Canon logo SKIP No display LOGO User sc...

Page 159 - Power management setting inquiry

Projector User Commands - 153 - Revision History / Date Changes Revised by Approved by GET PMM Power management setting inquiry Format GET □ PMM ? △ PMM Response g:PMM=<Setting:ID> <Setting:ID> OFF OFF STANDBY Standby mode EXIT Exit mode For details on other responses, refer to the "...

Page 160 - GET POWER; Power status inquiry

Projector User Commands - 154 - Revision History / Date Changes Revised by Approved by GET POWER Power status inquiry Format GET □ POWER ? △ POWER Response g:POWER=<Power status:ID> <Power status:ID> OFF Power Off OFF2ON Transitioning from power off → on ON Power On ON2PMM Transitioning ...

Page 161 - GET PRODCODE; Product information inquiry

Projector User Commands - 155 - Revision History / Date Changes Revised by Approved by GET PRODCODE Product information inquiry Format GET □ PRODCODE ? △ PRODCODE Response g:PRODCODE="<Product name:Character string>" Product name SX50 SX6 SX60 X600 SX7 X700 SX7 Mark II SX7 Mark II M Fo...

Page 162 - Progressive value setting inquiry

Projector User Commands - 156 - Revision History / Date Changes Revised by Approved by GET PROG Progressive value setting inquiry Format GET □ PROG ? △ PROG Response g:PROG=<Set (status) value:ID> <Set (status) value:ID> Errors supported by model Parameter Meaning SX50 SX6, SX60, X600 SX...

Page 163 - Remote control setting inquiry

Projector User Commands - 157 - Revision History / Date Changes Revised by Approved by GET RCCH Remote control setting inquiry Format GET □ RCCH ? △ RCCH Response g:RCCH=<Setting:ID> <Setting:ID> 1 Remote control channel 1 2 Remote control channel 2 For details on other responses, refer ...

Page 164 - RGB gain adjustment value inquiry

Projector User Commands - 158 - Revision History / Date Changes Revised by Approved by GET RGBGAIN RGB gain adjustment value inquiry Format GET □ RGBGAIN ? △ RGBGAIN Response g:RGBGAIN=<R adjustment value ： Number> ▽ <G adjustment value ： Number> ▽ <B adjustment value ： Number> For...

Page 165 - RGB offset adjustment value inquiry

Projector User Commands - 159 - Revision History / Date Changes Revised by Approved by GET RGBOFFSET RGB offset adjustment value inquiry Format GET □ RGBOFFSET ? △ RGBOFFSET Response g:RGBOFFSET=<R adjustment value: Number> ▽ <G adjustment value: Number> ▽ <B adjustment value: Number&...

Page 166 - GET ROMVER; ROM version inquiry

Projector User Commands - 160 - Revision History / Date Changes Revised by Approved by GET ROMVER ROM version inquiry Format GET □ ROMVER ? △ ROMVER Response g:ROMVER="<ROM VERSION ： Character string>" <ROM VERSION> := 99.9999 For details on other responses, refer to the "Err...

Page 167 - Color saturation value setting inquiry

Projector User Commands - 161 - Revision History / Date Changes Revised by Approved by GET SAT Color saturation value setting inquiry Format GET □ SAT ? △ SAT Response g:SAT=<Color saturation value setting:Number> For details on other responses, refer to the "Error List". Description T...

Page 168 - GET SCRNASPECT; Screen aspect inquiry

Projector User Commands - 162 - Revision History / Date Changes Revised by Approved by GET SCRNASPECT Screen aspect inquiry Format GET □ SCRNASPECT ? △ SCRNASPECT Response g: SCRNASPECT=<Aspect parameter:ID> <Aspect parameter:ID> 4:3 4:3 display 16:9 16:9 display 16:9_DIS 16:9 Digital Im...

Page 169 - GET SEL; Input signal inquiry

Projector User Commands - 163 - Revision History / Date Changes Revised by Approved by GET SEL Input signal inquiry Format GET □ SEL ? △ SEL Response g:SEL=<Input signal:ID> <Input signal:ID> PAL Includes PAL-M and PAL-N SECAM NTSC Includes NTSC4.43 1080i Includes 540p (1080i non-interla...

Page 170 - Sharpness value setting inquiry

Projector User Commands - 164 - Revision History / Date Changes Revised by Approved by GET SHARP Sharpness value setting inquiry Format GET □ SHARP ? △ SHARP Response g;SHARP=<Sharpness setting:Number> For details on other responses, refer to the "Error List". Description This command ...

Page 171 - GET SIGNALSTATUS; Signal status inquiry

Projector User Commands - 165 - Revision History / Date Changes Revised by Approved by GET SIGNALSTATUS Signal status inquiry Format GET □ SIGNALSTATUS ? △ SIGNALSTATUS Response g:SIGNALSTATUS=<Signal status:ID> <Signal status:ID> NO_SIGNAL Signal not detected DISPLAYING Image now displa...

Page 172 - Temperature inquiry

Projector User Commands - 166 - Revision History / Date Changes Revised by Approved by GET TEMP Temperature inquiry Format GET □ TEMP ? △ TEMP Response g:TEMP=<Number of temperature sensors:Number>,<Temperature measurement 1:Number>, …,<Temperature measurement n:Number> <Number ...

Page 173 - GET TERMINAL; Terminal setting inquiry

Projector User Commands - 167 - Revision History / Date Changes Revised by Approved by GET TERMINAL Terminal setting inquiry Format GET □ TERMINAL ? △ TERMINAL Response g:TERMINAL=<Setting:ID> <Setting:ID> IN This sets to input OUT This sets to output For details on other responses, refe...

Page 174 - Tracking adjustment value inquiry

Projector User Commands - 168 - Revision History / Date Changes Revised by Approved by GET TRACK Tracking adjustment value inquiry Format GET □ TRACK ? △ TRACK Response g:TRACK=<Tracking adjustment value:Number> For details on other responses, refer to the "Error List". Description Thi...

Page 175 - Vertical digital image shift setting inquiry

Projector User Commands - 169 - Revision History / Date Changes Revised by Approved by GET VDISHIFT Vertical digital image shift setting inquiry Format GET □ VDISHIFT ? △ VDISHIFT Response g: VDISHIFT=<Vertical shift amount:Number> For details on other responses, refer to the "Error List&#...

Page 176 - Vertical/horizontal keystone setting inquiry

Projector User Commands - 170 - Revision History / Date Changes Revised by Approved by GET VKS/HKS Vertical/horizontal keystone setting inquiry Format Vertical keystone setting inquiry Horizontal keystone setting inquiry GET □ VKS GET □ HKS ? △ VKS ? △ HKS Response g:VKS=<Vertical keystone settin...

Page 177 - Screen color correction inquiry

Projector User Commands - 171 - Revision History / Date Changes Revised by Approved by GET WB Screen color correction inquiry Format GET □ WB ? △ WB Response g:WB=<Screen color correction value:ID> <Screen color correction value:ID> NORMAL Standard GREENBOARD Blackboard ADJUST Adjust For...

Page 178 - GET WBRGB; Screen color correction (adjustment) inquiry

Projector User Commands - 172 - Revision History / Date Changes Revised by Approved by GET WBRGB Screen color correction (adjustment) inquiry Format GET □ WBRGB ? △ WBRGB Response g:WBRGB=<R adjustment value:Number> ▽ <G adjustment value:Number> ▽ <B adjustment value:Number> For de...

Page 179 - Setting range request

Projector User Commands - 173 - Revision History / Date Changes Revised by Approved by RANGE Setting range request Format RANGE □ <Parameter> Parameter Parameter Meaning POWER Power supply state BLANK BLANK status AUTOSETEXE Auto setup INPUT Input state DOTS Total dot number TRACK Tracking HPO...

Page 181 - RANGE 6AXADJ; -axis adjustment option inquiry

Projector User Commands - 175 - Revision History / Date Changes Revised by Approved by RANGE 6AXADJ 6-axis adjustment option inquiry Format RANGE □ 6AXADJ Response r:6AXADJ=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the...

Page 183 - Advanced color adjustment option request

Projector User Commands - 177 - Revision History / Date Changes Revised by Approved by RANGE ACADJUST Advanced color adjustment option request Format RANGE □ ACADJUST Response r:ACADJUST=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses...

Page 184 - Screen setting option request

Projector User Commands - 178 - Revision History / Date Changes Revised by Approved by RANGE ASPECT Screen setting option request Format RANGE □ ASPECT Response r:ASPECT=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the &#...

Page 185 - Auto setup setting option request

Projector User Commands - 179 - Revision History / Date Changes Revised by Approved by RANGE AUTOSETEXE Auto setup setting option request Format RANGE □ AUTOSETEXE Response r:AUTOSETEXE=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses,...

Page 186 - Audio volume setting range request

Projector User Commands - 180 - Revision History / Date Changes Revised by Approved by RANGE AVOL Audio volume setting range request Format RANGE □ AVOL Response r:AVOL=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List". ...

Page 187 - BLANK setting option request

Projector User Commands - 181 - Revision History / Date Changes Revised by Approved by RANGE BLANK BLANK setting option request Format RANGE □ BLANK Response r:BLANK=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the "E...

Page 188 - Brightness setting range request

Projector User Commands - 182 - Revision History / Date Changes Revised by Approved by RANGE BRI Brightness setting range request Format RANGE □ BRI Response r:BRI=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List". Descr...

Page 189 - Beep sound setting option request

Projector User Commands - 183 - Revision History / Date Changes Revised by Approved by RANGE BVOL Beep sound setting option request Format RANGE □ BVOL Response r:BVOL=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the "...

Page 190 - Contrast setting range request

Projector User Commands - 184 - Revision History / Date Changes Revised by Approved by RANGE CONT Contrast setting range request Format RANGE □ CONT Response r:CONT=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List". Desc...

Page 191 - RANGE DGAMMA; Dynamic gamma setting option request

Projector User Commands - 185 - Revision History / Date Changes Revised by Approved by RANGE DGAMMA Dynamic gamma setting option request Format RANGE □ DGAMMA Response r:DGAMMA=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to...

Page 192 - Total dot number setting range inquiry

Projector User Commands - 186 - Revision History / Date Changes Revised by Approved by RANGE DOTS Total dot number setting range inquiry Format RANGE □ DOTS Response r:DOTS=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List...

Page 194 - Digital video setting option inquiry

Projector User Commands - 188 - Revision History / Date Changes Revised by Approved by RANGE DVRANGE Digital video setting option inquiry Format RANGE □ DVRANGE Response r:DVRANGE=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer...

Page 195 - Focus lens continuous drive control option request

Projector User Commands - 189 - Revision History / Date Changes Revised by Approved by RANGE FCONTDRV Focus lens continuous drive control option request Format RANGE □ FCONTDRV Response r:FCONTDRV=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other...

Page 196 - Focus lens step drive control option request

Projector User Commands - 190 - Revision History / Date Changes Revised by Approved by RANGE FSTEPDRV Focus lens step drive control option request Format RANGE □ FSTEPDRV Response r:FSTEPDRV=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other respo...

Page 197 - Gamma adjustment range request

Projector User Commands - 191 - Revision History / Date Changes Revised by Approved by RANGE GAMMA Gamma adjustment range request Format RANGE □ GAMMA Response r:GAMMA=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List". D...

Page 198 - Guide setting enable option request

Projector User Commands - 192 - Revision History / Date Changes Revised by Approved by RANGE GUIDE Guide setting enable option request Format RANGE □ GUIDE Response r:GUIDE=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the...

Page 199 - Horizontal/vertical resolution setting range request

Projector User Commands - 193 - Revision History / Date Changes Revised by Approved by RANGE HPIX/VPIX Horizontal/vertical resolution setting range request Format Horizontal resolution setting range inquiry Vertical resolution setting range inquiry RANGE □ HPIX RANGE □ VPIX Response r:HPIX=N, <Mi...

Page 200 - Horizontal/vertical position adjustment range request

Projector User Commands - 194 - Revision History / Date Changes Revised by Approved by RANGE HPOS/VPOS Horizontal/vertical position adjustment range request Format Horizontal position adjustment range inquiry Vertical position adjustment range inquiry RANGE □ HPOS RANGE □ VPOS Response r:HPOS=N, <...

Page 201 - Hue setting range request

Projector User Commands - 195 - Revision History / Date Changes Revised by Approved by RANGE HUE Hue setting range request Format RANGE □ HUE Response r:HUE=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List". Description ...

Page 202 - Image mode setting option request

Projector User Commands - 196 - Revision History / Date Changes Revised by Approved by RANGE IMAGE Image mode setting option request Format RANGE □ IMAGE Response r:IMAGE=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the &...

Page 203 - Flip display setting option request

Projector User Commands - 197 - Revision History / Date Changes Revised by Approved by RANGE IMAGEFLIP Flip display setting option request Format RANGE □ IMAGEFLIP Response r:IMAGEFLIP=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, ...

Page 204 - Input selection setting option request

Projector User Commands - 198 - Revision History / Date Changes Revised by Approved by RANGE INPUT Input selection setting option request Format RANGE □ INPUT Response r:INPUT=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to ...

Page 205 - Key lock setting option request

Projector User Commands - 199 - Revision History / Date Changes Revised by Approved by RANGE KEYLOCK Key lock setting option request Format RANGE □ KEYLOCK Response r:KEYLOCK=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to t...

Page 206 - Lamp output setting option request

Projector User Commands - 200 - Revision History / Date Changes Revised by Approved by RANGE LAMP Lamp output setting option request Format RANGE □ LAMP Response r:LAMP=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the ...

Page 207 - Language setting option request

Projector User Commands - 201 - Revision History / Date Changes Revised by Approved by RANGE LANG Language setting option request Format RANGE □ LANG Response r:LANG=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the "E...

Page 209 - User image position setting option inquiry

Projector User Commands - 203 - Revision History / Date Changes Revised by Approved by RANGE LOGOPOS User image position setting option inquiry Format RANGE □ LOGOPOS Response r:LOGOPOS=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses,...

Page 210 - Memory color adjustment setting option request

Projector User Commands - 204 - Revision History / Date Changes Revised by Approved by RANGE MEMCADJ Memory color adjustment setting option request Format RANGE □ MEMCADJ Response r:MEMCADJ=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other respon...

Page 211 - Mute control setting option request

Projector User Commands - 205 - Revision History / Date Changes Revised by Approved by RANGE MUTE Mute control setting option request Format RANGE □ MUTE Response r:MUTE=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the &#...

Page 212 - RANGE NOSHOW; Display screen when nothing is shown setting option request

Projector User Commands - 206 - Revision History / Date Changes Revised by Approved by RANGE NOSHOW Display screen when nothing is shown setting option request Format RANGE □ NOSHOW Response r:NOSHOW=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on ot...

Page 213 - Display screen when there are no signals setting option request

Projector User Commands - 207 - Revision History / Date Changes Revised by Approved by RANGE NOSIG Display screen when there are no signals setting option request Format RANGE □ NOSIG Response r:NOSIG=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on o...

Page 214 - Display screen at startup setting option request

Projector User Commands - 208 - Revision History / Date Changes Revised by Approved by RANGE PJON Display screen at startup setting option request Format RANGE □ PJON Response r:PJON=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, re...

Page 215 - Power management setting option request

Projector User Commands - 209 - Revision History / Date Changes Revised by Approved by RANGE PMM Power management setting option request Format RANGE □ PMM Response r:PMM=I, <Setting option 1>, <Setting option 2>, ..., <Setting option n> For details on other responses, refer to the...

Page 216 - Power control setting option request

Projector User Commands - 210 - Revision History / Date Changes Revised by Approved by RANGE POWER Power control setting option request Format RANGE □ POWER Response r:POWER=I, <Setting option 1>, <Setting option 2>, ..., <Setting option n> For details on other responses, refer to ...

Page 217 - Progressive setting option request

Projector User Commands - 211 - Revision History / Date Changes Revised by Approved by RANGE PROG Progressive setting option request Format RANGE □ PROG Response r:PROG=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the ...

Page 218 - Remote control setting option request

Projector User Commands - 212 - Revision History / Date Changes Revised by Approved by RANGE RCCH Remote control setting option request Format RANGE □ RCCH Response r:RCCH=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the ...

Page 219 - RGB gain adjustment range request

Projector User Commands - 213 - Revision History / Date Changes Revised by Approved by RANGE RGBGAIN RGB gain adjustment range request Format RANGE □ RGBGAIN Response r:RGBGAIN=N, <R minimum value>, <R maximum value>, <G minimum value>, <G maximum value>, <B minimum value&...

Page 220 - RGB offset adjustment range inquiry

Projector User Commands - 214 - Revision History / Date Changes Revised by Approved by RANGE RGBOFFSET RGB offset adjustment range inquiry Format RANGE □ RGBOFFSET Response r:RGBOFFSET=N, <R minimum value>, <R maximum value>, <G minimum value>, <G maximum value>, <B minimu...

Page 221 - Color saturation setting range request

Projector User Commands - 215 - Revision History / Date Changes Revised by Approved by RANGE SAT Color saturation setting range request Format RANGE □ SAT Response r:SAT=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List"....

Page 222 - Screen aspect option inquiry

Projector User Commands - 216 - Revision History / Date Changes Revised by Approved by RANGE SCRNASPECT Screen aspect option inquiry Format RANGE □ SCRNASPECT Response r: SCRNASPECT=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, ref...

Page 223 - Input signal setting option request

Projector User Commands - 217 - Revision History / Date Changes Revised by Approved by RANGE SEL Input signal setting option request Format RANGE □ SEL Response r:SEL=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the "...

Page 224 - Sharpness setting range request

Projector User Commands - 218 - Revision History / Date Changes Revised by Approved by RANGE SHARP Sharpness setting range request Format RANGE □ SHARP Response r:SHARP=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List". ...

Page 225 - Terminal setting option request

Projector User Commands - 219 - Revision History / Date Changes Revised by Approved by RANGE TERMINAL Terminal setting option request Format RANGE □ TERMINAL Response r:TERMINAL=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer t...

Page 226 - Tracking adjustment range request

Projector User Commands - 220 - Revision History / Date Changes Revised by Approved by RANGE TRACK Tracking adjustment range request Format RANGE □ TRACK Response r:TRACK=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer to the "Error List"...

Page 227 - RANGE VDISHIFT; Vertical digital image shift setting option inquiry

Projector User Commands - 221 - Revision History / Date Changes Revised by Approved by RANGE VDISHIFT Vertical digital image shift setting option inquiry Format RANGE □ VDISHIFT Response r:VDISHIFT=N, <Minimum setting value>, <Maximum setting value> For details on other responses, refer ...

Page 228 - Vertical/horizontal keystone setting range request

Projector User Commands - 222 - Revision History / Date Changes Revised by Approved by RANGE VKS/HKS Vertical/horizontal keystone setting range request Format Vertical keystone setting inquiry Horizontal keystone setting inquiry RANGE □ VKS RANGE □ HKS Response r:VKS=N, <Minimum setting value>...

Page 229 - Screen color correction option request

Projector User Commands - 223 - Revision History / Date Changes Revised by Approved by RANGE WB Screen color correction option request Format RANGE □ WB Response r:WB=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other responses, refer to the "...

Page 230 - Screen color correction (adjustment) range request

Projector User Commands - 224 - Revision History / Date Changes Revised by Approved by RANGE WBRGB Screen color correction (adjustment) range request Format RANGE □ WBRGB Response r:WBRGB=N, <R minimum value>, <R maximum value>, <G minimum value>, <G maximum value>, <B min...

Page 231 - Zoom lens continuous drive control option request

Projector User Commands - 225 - Revision History / Date Changes Revised by Approved by RANGE ZCONTDRV Zoom lens continuous drive control option request Format RANGE □ CONTZDRV Response r:ZCONTDRV=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other ...

Page 232 - Zoom lens step drive control option request

Projector User Commands - 226 - Revision History / Date Changes Revised by Approved by RANGE ZSTEPDRV Zoom lens step drive control option request Format RANGE □ ZSTEPDRV Response r:ZSTEPDRV=I, <Setting option 1>, <Setting option 2>, …, <Setting option n> For details on other respon...

Page 236 - Appendix 1; Reset Items for SX50

Projector User Commands - 230 - Revision History / Date Changes Revised by Approved by Appendix 1 Reset Items for SX50 What is initialized by the "RESET" command for SX50 is set forth in the table below. ALL SYSTEM IMAGE Item Setting Reference command O Input source switching A-RGB2 INPUT O ...

Page 238 - Reset Items for SX7 Mark II

Projector User Commands - 232 - Revision History / Date Changes Revised by Approved by Reset Items for SX7 Mark II What is initialized by the "RESET" command for SX7 Mark II and is set forth in the table below. ALL SYSTEM IMAGE Item Setting Reference command O Input source switching A-RGB1 I...

Page 239 - Appendix 2

Projector User Commands - 233 - Revision History / Date Changes Revised by Approved by Appendix 2 Table of Response Patterns by Command for SX50, SX6, SX60, X600, SX7, X700 DG A1 A2 CM V SV DV SC X ON OFF 1 REMOTE 2 LOCALPOWER ONOFF AUTOSETEXE FOCUS VKSSCRNINPUT 5 BLANK 6 INPUT 7 ＡＵＴＯＰＣ ← ← 8 DOTS ←...

Page 242 - Table of Response Patterns by Command for SX7 Mark II

Projector User Commands - 236 - Revision History / Date Changes Revised by Approved by Table of Response Patterns by Command for SX7 Mark II DG A1 A2 CM V SV DV SC X ON OFF 1 REMOTE 2 LOCALPOWER ONOFFBLKON AUTOSETEXE FOCUS VKSSCRNINPUT 5 BLANK 6 INPUT 7 ＡＵＴＯＰＣ ← ← 8 DOTS ← ← 9 TRACK ← ← 10 HPOS ← ← ...

Table of Contents:

Other Manuals for Canon SX 50

Summary

Other Canon Models