Canon ES100- User Manual

The ES100 Series Cameras are compact, full performance,
general purpose B/W CCD Cameras, which use high sensitive
1/3

"

B/W interline transfer CCDs (Charge Coupled Device).

ES100, with AC power cord , has functions of ES on/off, AGC
on/off , and BLC on/off. Audio feature is built-in.

• Do not expose the camera to humidity and dust. If the camera is

mounted outdoor, a camera housing is required.

• Do not disassemble it or place it on an unstable base.

• Do not touch the surface of CCD sensor by hand directly. When

the camera is not in use, put the cover cap on the lens mount.

• Never face the camera toward the sun.

• Use Auto-iris lens or N.D. filter or set large F number of manual

lens when the light intensity is very high, in order to protect the
sensitive CCD sensor.

• Use proper AC power source otherwise the camera will not

function correctly.

ES100

Series

INSTRUCTION
MANUAL

1/3

"

B/W CCD Cameras

I.

General

II.

Precautions

Pickup Device:

1/3 inch interline
transfer CCD

Picture Element:

510x492(/E,EIA)
500x580(/C,CCIR)

Horizontal resolution:

420 TV lines

Sensitivity:

0.04 lux/F=1.2

S/N ratio:

Over 48 dB

Electronic shutter:

Up to 1/10,000

Auto. Iris:

Video Drive

BLC:

Yes

AGC ON/OFF:

Yes

Gamma Correction:

0.45

Video output:

1.0Vp-p,75 ohm

Power source:

AC 198 ~ 264V

Sync. Mode:

Internal Sync.

Lens Mount:

C or CS with Ring

Dimension:

42x47x100mm

Operating Temperature:

-10

o

C to +50

o

C

Storage Temperature:

-40

o

C to +70

o

C

V.

Specifications

MES1G00100

!

Remove the cover cap from the top of the lens mount.

"

If CS mount lens is used, please also remove the C Mount Ring
(the 5mm thick ring on top of the lens mount).

#

Screw the lens firmly onto the lens mount.

$

Connect the video output of the camera to a B/W monitor or other
video device through a 75 ohm type coaxial cable with BNC
female connector at camera end.

%

Plug the power cord to the outlet. Power indicator LED should
light if the power source is properly connected.

&

Once the image appears on the monitor, adjust the focus and
diaphragm of the lens to obtain the best picture.

'

If the subject is not in focus when adjusting focus of the lens, do
back focus adjustment as following:

i. Set the focus ring of the lens to infinity position.
ii. Take picture of subject at a distance more than 20m

away from the camera.

iii. Loosen the lens mount fixing screw located at

bottom of the front panel by using the L wrench.

iv. Turn the lens and the mount together so that the

subject is in focus.

v. Secure the lens mount fixing screw firmly again.

(

Mount the camera on the mounting bracket by using the mounting
hole at bottom of the front panel. If top mounting is required, fix
the top mounting base on top of the camera with two screws and
then mount camera to mounting bracket.

III

.

Installation Instructions

Pin1

Pin2

Pin3

Pin4

+12V VD-IRIS GND GND

IV.

Using Special Features

)

Using Auto Iris Lens

For ES100, please use video drive
iris lens. Wire the cable of lens to
Mini Plug according to the
following table:

)

Electronic Shutter ON/OFF

ES ON: The camera continuously adjusts the shutter speed from 1/60

(EIA),1/50 (CCIR) second to 1/10,000 second according to the
luminance conditions of the scene.

ES OFF: The shutter speed is fixed at 1/60 (EIA),1/50 (CCIR) second.

Set ES OFF, when auto iris lens is used or flicker is observed under a very
bright fluorescent lamp. Otherwise, turn ES on for optimum performance.

)

Automatic Gain Control ON/OFF

AGC ON: The sensitivity increases automatically when light is low.
AGC OFF: A low-noise picture is obtained under a low light condition.

)

Back Light Compensation

When BLC is turn on, the AGC, ES and IRIS operating point is
determined by averaging over the center area instead of entire field-of-
view, so that a dimly-lit foreground object at center area can be clearly
distinguished from brightly-lit backgrounds.
BLC should not be used unless it is needed to compensate for back-lit.

E.S.

ON

VIDEO

OFF

AUDIO

IRIS

1

2

AGC

ON

BLC

OFF