Page 2 - Copyright
Copyright Copyright 2011 by Canon Inc. All rights reserved.No part of this publication may be reproduced or transmitted in any form or by any means,electronic or mechanical, including photocopying and recording, or by any informationstorage or retrieval system without the prior written permission of...
Page 3 - Chapter 1
Contents Chapter 1 Preface................................................................................................................. 5 Notes for the reader................................................................................... 6 Naming conventions for finishers (commercial naming ...
Page 6 - Introduction; Indicates
Notes for the reader Introduction This manual helps you to use the Two-Knife Booklet Trimmer-A1. The manual containsa description of the product and guidelines to use and operate the Two-Knife BookletTrimmer-A1. Definition Attention-Getters Parts of this manual require your special attention. These ...
Page 7 - Laser beam; Warning; Indicates additional important information.; Note
Indicates Icon Word Laser beam Warning Ignoring this warning could cause injury or damage toproperty. Caution Indicates additional important information. Note The use of heat-resistant gloves is mandatory when youcarry out these actions. Important safety instructions Warning: Do not remove the safet...
Page 8 - Hardware and hardware naming in User Interfaces; Commercial product name:; Paper Folding Unit-F1
Naming conventions for finishers (commercial naming andnaming in User Interfaces) Hardware and hardware naming in User Interfaces To improve the readability of texts in User Interfaces of operator panels and software,the finishers are generally referred to by their function. The table below shows th...
Page 10 - Machine description; Illustration; More information; ‘Two-knife trim section’
Machine description Illustration Main sections Main sections # More information Section ‘Two-knife trim section’ on page 11 Two-knife trim section 1 ‘Conveyor section’ on page 13 Conveyor section 2 ‘Trim ejecting section’ on page 15 Trim ejecting section 3 Chapter 2 - Parts and their functions 10 Ma...
Page 11 - Two-knife trim section; Function; The top cover gives access to the trimmer.
Two-knife trim section Introduction Each booklet delivered from the upstream trimmer is trimmed along it's top and bottom.Then the booklet is delivered to the conveyor section. Illustration [11] Two-knife trim section Main parts Main parts # Function Part The top cover gives access to the trimmer. T...
Page 12 - Handle
Function Part The handle lifts the booklet transport unit (TF2). Handle B If a booklet jam occurs in the two-knife trim sec-tion, you must press the handle and lift the booklettransport unit (TF2) to remove the jammedbooklets.How to open the booklet transport unit (TF2):1. Press the handle to the le...
Page 13 - Conveyor section; The booklets delivered are laid out on the conveyor.
Conveyor section Introduction The booklets delivered are laid out on the conveyor. Illustration [12] The conveyor section Chapter 2 - Parts and their functions 13 Conveyor section
Page 14 - Booklet detect sensor
Main parts Main parts # Function Part Grip the handle and lift the roller unit when youremove the booklets from the conveyor. Handle (TE) A The delivery transport rollers hold the finishedbooklets. The position of the rollers is set automat-ically to match the booklet size. Delivery transportrollers...
Page 15 - Trim ejecting section
Trim ejecting section Introduction The trim waste is ejected into the trimmer waste box through this section. Illustration [13] Trim ejecting section Chapter 2 - Parts and their functions 15 Trim ejecting section
Page 16 - Trim Full sensor
Main parts Main parts # Function Part If trim waste is present betweenthe sensor and the reflector, theoperator panel displays the mes-sage 'Empty the two-knife trim-mer waste box.'. Trim Full sensor A Trim waste is ejected into thetrim box through this chute. Delivery chute B The trimmer waste box ...
Page 18 - Turn the trimmer on; How to turn on the trimmer
Turn the trimmer on How to turn on the trimmer 1. Put the On/Off button of Saddle Finisher-AF2 into the "I" position. 2. Press the On/Off button on top of the printer, next to the base of the operator panel. Result The trimmer will be turned on because the trimmer is connected to Saddle Fini...
Page 19 - Operation while trimming; This section describes the main actions when using the trimmer.; Delivery tray
Operation while trimming Introduction This section describes the main actions when using the trimmer. Illustration [14] Empty the delivery tray and the trimmer waste box # Delivery tray A Trim Full sensor B Trimmer waste box C Chapter 3 - Operating procedures 19 Operation while trimming
Page 20 - Empty the delivery tray; Be careful not to drop a booklet while removing it.; Empty the trimmer waste box; You must empty the trimmer waste box when:; Remove jammed booklets
Empty the delivery tray When the machine stops because the delivery tray is full, you must remove the bookletsfrom the delivery tray.The machine will restart automatically. Note: When you remove the booklets before the delivery tray is full, you can increase theproductivity without interrupting the ...
Page 21 - ‘Clear a paper jam’
[15] The covers of the trimmer # Top cover A Transport section B Delivery section cover C Opening the transport unit D Note: If a booklet jam occurs frequently, refer to ‘Clear a paper jam’ on page 27 for instructions on how to correct the problem. Chapter 3 - Operating procedures 21 Operation while...
Page 22 - Remove or install the delivery tray
Remove or install the delivery tray Illustration [16] Remove the delivery tray A. Locking knobsB. Delivery tray How to remove the delivery tray 1. To remove the delivery tray, loosen the 2 locking knobs. 2. Lift the delivery tray up to remove. 3. Tighten the two locking knobs. How to install the del...
Page 24 - Error messages; turn on Saddle Finisher-AF2 and the printer again.
Error messages Introduction When an error occurs and the machine does not work properly, the operator panel willdisplay the message 'Call service.'. When this messages is displayed, keep in mind thefollowing cautions. Warning: Do not plug in or pull out the power plug with wet hands. This may cause ...
Page 25 - Overview of possible errors; Solution; The top cover is open.
Overview of possible errors Introduction When an error occurs in the trimmer, the printer operator panel displays a correspondingmessage. The table below describes possible solutions for trimmer-related errors. Illustration [17] Error locations Possible errors Errors and solutions # Solution Cause o...
Page 27 - Clear a paper jam; Paper jams can occur at the following locations:
Clear a paper jam Introduction Paper jams can occur at the following locations: # Conveyor section A Trim section B When a paper jam occurs, the jam is always caused by a paper chip jam or dirty transportbelts. The table below describes these causes and the solutions. Illustration [18] Clear a paper...
Page 28 - How to clear a paper jam; Open the transport unit.
How to clear a paper jam # Solution Cause of jam • Open the transport unit. • Check if any paper chips are left onthe booklet feed path. • Remove the paper chips. Paper chip jam Clean the transport belts. Contact yourlocal authorized dealer. Transport belts are dirty Chapter 4 - Troubleshooting 28 C...
Page 30 - Specifications; Description
Specifications Two-Knife Booklet Trimmer-A1 Note: Whenever a number of sheets is mentioned in the table below, the figure is based onmedia of 80 g/m² (20 lb Bond). Specifications of Two-Knife Booklet Trimmer-A1 # Specifications Item Top-bottom trimmer Description 50 sheets or 48 sheets + 2 sheets of...
