Cadet EBHN500-8 - Manual

Cadet EBHN500-8

Cadet EBHN500-8 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
Page: / 10

Table of Contents:

  • Page 2 – THERMOSTAT; PLACEMENT; BEFORE PROCEEDING WITH THE INSTALLATION INSTRUCTIONS, YOU MUST; WIRING; INSTALLATION INSTRUCTIONS; DO NOT INSTALL ANY BASEBOARD
  • Page 3 – STEP 1: Mount Heater to Wall
  • Page 4 – Maintenance; HOW SOFTHEAT HYDRONIC
  • Page 5 – Symptom Problem Solution; TROUBLESHOOTING CHART
  • Page 6 – GUÍA PARA EL PROPIETARIO; INSTRUCCIONES IMPORTANTES; Características y Beneficios; Operación más silenciosa y bajas temperaturas en la superficie
  • Page 7 – TERMOSTATO; UBICACIÓN; DIVERSOS FACTORES QUE SON FUNDAMENTALES PARA LA INSTALACIÓN.; CABLEADO; INSTRUCCIONES PARA LA INSTALACIÓN; NO INSTALE EL ZÓCALO DEBAJO
  • Page 8 – PASO 1: Montaje mural del calentador; Ubicación del; Piso; PRECAUCIÓN –
  • Page 9 – Aire fresco; CÓMO FUNCIONAN LOS ZÓCALOS
  • Page 10 – SÍNTOMA PROBLEMA SOLUCIÓN; TABLA DE RESOLUCIÓN DE PROBLEMAS; GARANTÍA
Loading the manual

OWNER’S GUIDE

MODELS:

EBHN500
EBHN750
EBHN1000
EBHN1250
EBHN1500
EBHN500-8
EBHN750-8
EBHN1000-8
EBHN1250-8
EBHN1500-8

TOOLS REQUIRED

Phillips Screwdriver

Straight Screwdriver

Wire Strippers

Drill or Hammer

Level

Punch or Chisel

Drill Bits

Utility Knife

(4) Wood Screws

(3) Wire Nuts

(1) Strain Relief Connector

IMPORTANT INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING!

Turn the electrical power off at the electrical panel
board (circuit breaker or fuse box) and lock or tag the
panel board door to prevent someone from turning
on power while you are working on the heater.
Failure to do so could result in serious electrical
shock, burns, or possible death.

When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Read all instructions and labels before installing this heater.

2.

WARNING

A heater has hot and arcing parts inside. Do not install in
areas where gasoline, paint or flammable liquids are stored or
excessive lint or dust are present.

3.

WARNING

This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes and curtains away from heater.

4. To prevent possible fire, do not block air intakes or exhaust in

any manner. Do not use on soft surfaces, like a bed, where
openings may become blocked. Heaters must be kept clean of
excessive lint, dirt and debris. (See Maintenance Instructions).

5.

Risk of electrical shock

. Do not insert or allow foreign objects to

enter any ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.

6. Do not place heater below an electrical convenience receptacle.

7.

WARNING

Overheating or fire may occur

. Do not install the heater behind

doors.

8. Use extreme caution when any heater is used near children or

invalids and whenever the heater is left operating unattended.

9.

WARNING

Do not operate after heater malfunctions or has been dropped
or damaged in any manner.

10.

WARNING

Risk of fire. Do not block heater

minimum of 12 inches in front

and above, 6 inches on both sides.

11. Use this heater only as described in this manual. Any other use

not recommended by the manufacturer may cause fire, electrical
shock, or injury to persons.

12.

Verify that the electrical supply wires are the same voltage as
the heater.

The heater must be grounded to the grounding

screw provided. If you need to install a new circuit or need
additional wiring information, consult a qualified electrician.

Tel: 360-693-2505 www.cadetco.com P.O. Box 1675 Vancouver, WA 98668-1675

Features & Benefits

Whisper quiet operation and low surface temperatures

Filled with non-toxic, non-hazardous thermal fluid

Self-contained hermetically sealed element design requires no
plumbing, piping, or other water supply

Thermal fluid capacity offers better heat retention, which creates
less cycling and keeps more consistent room temperatures

Designed to reduce the effects of indoor allergens

7-year element warranty

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - THERMOSTAT; PLACEMENT; BEFORE PROCEEDING WITH THE INSTALLATION INSTRUCTIONS, YOU MUST; WIRING; INSTALLATION INSTRUCTIONS; DO NOT INSTALL ANY BASEBOARD

THERMOSTAT A thermostat is required. A Cadet wall thermostat is recommended for optimum performance, or you may prefer the convenience of a built-in EBKN DPST thermostat kit. For instructions on wiring a thermostat, see the instructions that were included with your thermostat. If you are installing ...

Page 3 - STEP 1: Mount Heater to Wall

INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS AND SAFETY INFORMATION. CAUTION - High Temperature, Keep Electrical Cords, Drapes, And Other Furnishings Away From Heater WARNING! RISK OF ELECTRICAL SHOCK. TURN OFF ALL POWER AT THE ELECTRICAL PANEL BOARD SUPPLYING POWER TO THE HEATER BEFORE DOING ANY...

Page 4 - Maintenance; HOW SOFTHEAT HYDRONIC

INSTALLATION INSTRUCTIONS Inside a Softheat baseboard a hermetically sealed heat transfer fluid isheated by an electric heating element. As the solution is heated, warmthis generated and transmitted through dozens of aluminum fins along theheater tube (it could initially take 30 to 60 minutes to war...

Other Cadet Models