Cadet CB103T - Manual
Cadet CB103T – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installation Instructions; How do I install for new construction?; How do I install in an existing wall?; READ ALL; Figure 3
- Page 3 – 40 VOLT POWER SUPPLY
- Page 4 – Operation & Maintenance; Figure 9; How do I insert the heater assembly into the wall can?
- Page 5 – Warranty; Symptom Problem; Troubleshooting Chart; WARNING; IMPORTANT INSTRUCTIONS
- Page 6 – GUÍA DEL PROPIETARIO PARA MODELOS DE MULTIVOLTAJE; The Com-Pak Bath Heater; Características y Beneficios; ADVERTENCIA
- Page 7 – Instrucciones para la instalación; guía; LEA TODAS LAS; Parte Uno; Continúe con la PARTE DOS.; Figura 3
- Page 8 – Figura 5
- Page 9 – Funcionamiento y mantenimiento; Figura 9; ¿Cómo se coloca la unidad del calentador en la cámara de pared?; Instale la unidad del calentador; La garantía pierde
- Page 10 – Garantía; Síntoma Problema; INSTRUCCIONES IMPORTANTES; Tabla de resolución de problemas
- Page 11 – BLANK
The Com-Pak Bath Heater
OWNER’S GUIDE FOR MULTI-VOLT MODELS
SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
The Com-Pak Bath Heater
TOOLS REQUIRED:
Phillips Screwdriver
Straight Screwdriver
Wire Strippers
Utility Knife
(4) 1
1
/
2
" Wood Screws
Insulated Wire Connectors
(1) Strain Relief Connector
WARNING
Turn the electrical power off at the electrical panel
board (circuit breaker or fuse box) and lock or tag
the panel board door to prevent someone from
turning on power while you are working on the
heater. Failure to do so could result in serious
electrical shock, burns, or possible death.
1.
Read all instructions before using this heater.
2.
Read all information labels.
Verify that the electrical
supply wires are the same voltage as the heater.
3.
All electrical work and materials must comply with the
National Electric Code (NEC), the Occupational Safety
and Health Act (OSHA), and all state and local codes.
4.
Connect the grounding screw provided in the wall can to
the supply ground wire.
5.
If you need to install a new circuit or need additional
wiring information, consult a qualified electrician.
6.
Protect electrical supply from kinks, sharp objects, oil,
grease, hot surfaces or chemicals.
7.
WARNING
Overheating or fire may occur. DO NOT
install the heater
in a floor, in the ceiling, below a towel bar, behind a door, or
anywhere the air discharge may be blocked in any manner.
8.
WARNING
Fire or explosion may occur. DO NOT
install heater in any
area where combustible vapors, gases, liquids, or excessive
lint or dust are present.
9.
WARNING
DO NOT
install where heater is likely to get wet.
10.
WARNING
Heater must be connected to a GFCI protected branch circuit.
11.
WARNING
Burn Hazard.
This heater is hot when in use. To avoid burns,
do not let bare skin touch hot surfaces. Use extreme caution
when any heater is used by or near children or invalids.
12.
WARNING
Risk of Electrical Shock. DO NOT
install the heater directly
above bathtub or sink. DO NOT install in shower stall area
(Manufacturer recommends a minimum 2 foot clearance).
13.
WARNING
Risk of Electrical Shock.
Connect grounding lead to grounding
screw provided. Keep all foreign objects out of heater.
14.
WARNING
Risk of Electrical Shock.
Never place a switch where it can
be reached from the tub or shower enclosure.
15.
WARNING
Risk of Fire. Do not block heater.
Heater must be kept clear
of all obstructions: a minimum of 3 feet in front, 6 inches
above and on both sides. Heater must be kept clean of lint,
dirt and debris. (See Maintenance Instructions.)
www.cadetco.com Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675
Features & Benefits
■
Thermal safeguard
•
High temperature manual reset:
turns off heater if normal operating
temperatures are exceeded
■
Commercial grade steel element - painted to resist rusting
■
Built-in controls
- Single pole thermostat with disabled (no heat) position
- 60 minute timer overrides thermostat for instant warmth
■
Powder coat paint process eliminates sharp cutting edges
■
Three year extended warranty on element and motor
■
Factory tested
■
Multi-Volt configurations
120 or 240 Volt AC (1000 Watts)
*Factory set at 240-Volts
Models:
CBC103TW or CB103T The Com-Pak Bathroom Heater
1/2” Depth
1.27cm
10” Width
25.4cm
12 5/8” Height
32.07cm
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Cadet CB103T
Summary
STRAIN RELIEF CONNECTOR KNOCK-OUT (TWIST TO REMOVE) SUPPLY WIRE GROUNDING SCREW Installation Instructions How do I install for new construction? Figure 1 Face of wall can must extend ½ or 5 / 8 inch from face of stud to allow for thickness of sheetrock. The CB Series heater REQUIRES A MINIMUM distan...
Installation Instructions WARNING Turn the electricalpower off at theelectrical panelboard (circuitbreaker or fuse box)and lock or tag thepanel board door to prevent someonefrom turning onpower while you are working on theheater. Failure to do so could result in serious electricalshock, burns, orpos...
Operation & Maintenance How to operate your heater 1. Once installation is complete and power has been restored, turn the thermostat knob fully clockwise. (The thermostat is on the right.) 2. When the room reaches your comfort level, turn the thermostat knob counterclockwise until the heater tur...
