Cadet 8F2500-8 - User Manual
Cadet 8F2500-8 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – BASEBOARD WIRING; A thermostat is required.; AREA OF INSTALLATION; Installation Instructions
- Page 3 – Left Side Wiring; Thermostat Kit Wiring; Operation & Maintenance; Maintenance
- Page 4 – Warranty; Warranty Information; All Cadet Products; THESE WARRANTIES DO NOT APPLY:; Symptom; Troubleshooting Chart
240 Volt Models:
2F350
2F500
3F750
4F1000
5F1250
6F1500
8F2000
8F2500
10F2500
120 Volt Models:
2F500-1
3F750-1
4F1000-1
6F1500-1
208 Volt Models:
2F500-8
3F750-8
4F1000-8
5F1250-8
6F1500-8
8F2000-8
8F2500-8
Tools Required:
Phillips Screwdriver
Straight Screwdriver
Wire Strippers
Drill or Hammer
Drill Bits
4 Wood Screws
3 Wire Nuts
1 Strain Relief Connector
OWNER’S GUIDE
The Cadet
Electric Baseboard
General Safety Information
Keep For Future Reference
WARNING!
Turn the electrical power off at the electrical
panel board (circuit breaker or fuse box) and
lock or tag the panel board door to prevent
someone from turning on power while you
are working on the heater. Failure to do so
could result in serious electrical shock,
burns, or possible death.
1.
Read all information labels.
Verify that the electrical supply
wires are the same voltage as the heater.
2.
All electrical work and materials must comply with the
National Electric Code (NEC), the Occupational Safety and
Health Act (OSHA), and all state and local codes.
3.
The heater must be grounded to the grounding pigtail (cop-
per wire) provided.
4.
If you need to install a new circuit or need additional wiring
information, consult a qualified electrician.
5.
Protect electrical supply from kinks, sharp objects, oil,
grease, hot surfaces or chemicals.
6.
WARNING
Overheating or fire may occur. DO NOT
place the heater
behind doors.
7.
WARNING
Fire or explosion may occur. DO NOT
place heater in any
area where combustible vapors, gases, liquids, or exces-
sive lint or dust are present.
8.
WARNING
Risk of Electrical Shock.
Turn off all power at the electri-
cal panel board supplying power to the heater before
wiring your heater.
9.
WARNING
Risk of Fire.
Heater must be kept clear of all obstructions:
maintain a 12” minimum clearance in front and above the
heater with a 6” minimum on each side. Heaters must be
kept clean of lint, dirt and debris. (See Maintenance
Instructions)
• Oversized high temperature limit switch with full length
sensor for added safety
• Durable steel sheathed element with a lifetime warranty
• Rugged steel construction
Features & Benefits
TEL: 360-693-2505 Fax: 360-694-6939 P.O. Box 1675 Vancouver, WA 98668-1675
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Cadet 8F2500-8
Summary
More than one baseboard heater can be wired inparallel on same circuit (Be sure to check nationaland local codes for safety requirements). Disconnect (see Figure 3) splice "B" or "C" (NOTBOTH). DO NOT disconnect splice "A". Take onewire from each disconnected lead and connect...
Thermostat Kit Wiring (Supply wire colors may vary. Our reference to colors assumes general stan-dards) BTF-1 (See Figure 8) Connect supply black wire to the red thermostat wire. Connect black thermostatwire to one heater wire. Check to be sure the other supply wire is connecteddirectly to heater wi...
Warranty Warranty Information Maintenance: For safer operation and to prolong the life of the heater, it is necessary to follow the maintenance instructions included with each heater. Failure to properly maintain the heater will result in the warranty being voided. All warranties offered to original...
