Cadet 5F1250-8 - Manual
Cadet 5F1250-8 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – THERMOSTAT; A thermostat is required.; If you; PLACEMENT; BEFORE PROCEEDING WITH THE INSTALLATION INSTRUCTIONS, YOU MUST; WIRING; ABOUT THE CADET ELECTRIC BASEBOARD:; Installation Instructions; DO NOT INSTALL ANY BASEBOARD
- Page 3 – STEP 2: Baseboard Wiring
- Page 4 – STANDARD BASEBOARD WIRING ON RIGHT SIDE; MULTI-WATT BASEBOARDS: WIRING ON RIGHT SIDE; For single wattage baseboards, refer to “Standard Baseboards.”; MULTI-WATT BASEBOARDS: WIRING ON LEFT SIDE
- Page 5 – Multiple Baseboard Wiring - Optional; Baseboard wiring with a wall thermostat - Optional; SINGLE POLE WALL THERMOSTAT
- Page 6 – Troubleshooting Chart; LIMITED LIFETIME WARRANTY:; Operation & Maintenance; How To Operate Your Heater
- Page 7 – INFORMACIÓN IMPORTANTE; Características y Beneficios; Fácil instalación con caja perforada a intervalos de 1”; HERRAMIENTAS REQUERIDAS; GUÍA PARA EL PROPIETARIO; Calentador Eléctrico
- Page 8 – ANTES DE PROCEDER CON LAS INSTRUCCIONES DE INSTALACIÓN, DEBE; CABLEADO; ACERCA DEL ZÓCALO ELÉCTRICO CADET:; Instrucciones Para La Instalación; Espac; NO INSTALE NINGÚN ZÓCALO DEBAJO
- Page 9 – PASO 1: Montaje mural del calentador; PASO 2: Cableado del zócalo
- Page 10 – ZÓCALOS ESTÁNDAR: CABLEADO EN EL LADO DERECHO
- Page 11 – Nota; Cableado de múltiples zócalos - Opcional; Cableado del zócalo con un termostato mural – Opcional; TERMOSTATO MURAL DE UN SOLO POLO; BAJO
- Page 12 – SER REALIZADOS POR PERSONAL DE SERVICIO ELÉCTRICO CALIFICADO; Síntoma; Tabla de Resolución de Problemas; Funcionamiento y Mantenimiento; Cómo hacer funcionar el calentador; Mantenimiento
240/208 VOLT MODELS
2F350
6F1500
2F500
8F2000
3F750
8F2500
4F1000
8F2025
5F1250
10F2500
208 VOLT MODELS
2F500-8
3F750-8
4F1000-8
5F1250-8
6F1500-8
8F2000-8
8F2500-8
120 VOLT MODELS
2F500-1
3F750-1
4F1000-1
6F1500-1
The Cadet
Electric Baseboard
OWNER’S GUIDE
IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING!
Turn the electrical power off at the electrical
panel board (circuit breaker or fuse box) and
lock or tag the panel board door to prevent
someone from turning on power while you are
working on the heater. Failure to do so could
result in serious electrical shock, burns, or
possible death.
1. Read all instructions before using this heater.
2. Read all information labels.
Verify that the electrical supply
wires are the same voltage as the heater.
3. All electrical work and materials must comply with the
National Electric Code (NEC), the Occupational Safety and
Health Act (OSHA), and all state and local codes.
4. The heater must be grounded to the grounding pigtail (copper
wire) provided.
5. If you need to install a new circuit or need additional wiring
information, consult a qualified electrician.
6. Protect electrical supply from kinks, sharp objects, oil, grease,
hot surfaces or chemicals.
7. Do not place heater against paperboard or low-density
cellulose fiberboard surfaces.
8. Do not place heater below an electrical convenience receptacle.
9.
WARNING
Overheating or fire may occur.
Do not install the heater behind doors.
10.
WARNING
Fire or explosion may occur.
Heater has hot and arcing or sparking
parts inside. Do not install heater in any area where combustible
vapors, gases, liquids, or excessive lint or dust are present.
11.
WARNING
Burn Hazard.
This heater is hot when in use. To avoid burns, do
not let bare skin touch hot surfaces. Use extreme caution when
any heater is used by or near children or invalids and whenever
the heater is left operating unattended.
12.
WARNING
Risk of electrical shock.
Keep all foreign objects out of heater.
Do not operate after heater malfunctions or has been dropped
or damaged in any manner.
13.
WARNING
Risk of Fire. Do not block heater.
Heater must be kept clear of
all obstructions: minimum of 12 inches in front and above,
6 inches on both sides. Heaters must be kept clean of excessive
lint, dirt and debris. (See Maintenance Instructions)
14. Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electrical
shock, or injury to persons.
Features & Benefits
•
Oversized high temperature limit switch with full
length sensor for added safety
•
Durable steel sheathed element with a limited
lifetime warranty
•
Easy installation with pre-punched case at 1” intervals
•
Rugged steel construction
•
Thermostat not included
www.cadetco.com
Tel: 360-693-2505
P.O. Box 1675
Vancouver, WA
98668-1675
TOOLS REQUIRED
•
#2 Phillips
Screwdriver
•
Straight
Screwdriver
•
Wire Strippers
•
Drill or Hammer
•
Drill Bits
•
(4) Wood Screws
•
Wire Connectors
•
(1) Strain Relief
Connector
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Cadet 5F1250-8
Summary
THERMOSTAT A thermostat is required. A Cadet wall thermostat is recommended for optimum performance, or you may prefer the convenience of abuilt-in thermostat kit. For instructions on wiring a thermostat, seethe instructions that were included with your thermostat. If you are installing a wall therm...
NOTE: You do not need to disassemble any additional parts to mountthe heater. Installation Instructions WIRINGCOMPARTMENT COVER MOUNT SECURELY TO WALL Figure 7 Model 8F2025 Only SUPPLY WIRES GROUND WIRE GROUNDING PIGTAIL WIRE CONNECTOR B A GROUND DO NOT DISCONNECT Figure 6 B A GROUND DO NOT DISCONNE...
Figure 9 Left Side Wiring Shown Figure 8 Right Side Wiring Shown STANDARD BASEBOARD WIRING ON RIGHT SIDE 120V OR 240V SUPPLY (See Figure 8)1. Connect one supply wire to one heater wire.2. Connect remaining supply wire to remaining heater wire.3. Replace wiring compartment cover and secure with screw...
