Page 3 - WPIM-RT1 User’s Guide; NOTICE; FCC NOTICE
WPIM-RT1 User’s Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, fi...
Page 4 - Notice; ii; VCCI NOTICE
Notice ii WPIM-RT1 User’s Guide INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de br...
Page 6 - iv
Notice iv WPIM-RT1 User’s Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the Commercial Computer Sof...
Page 9 - CONTENTS
WPIM-RT1 User’s Guide vii CONTENTS INTRODUCTION ...................................................................................... ix Using This Manual .......................................................................... ixStructure of This Guide...............................................
Page 11 - INTRODUCTION; USING THIS MANUAL; Chapter 1; Overview; Chapter 2; Setup and Installation; Chapter 3; Local Management; Appendix A; Specifications
WPIM-RT1 User’s Guide ix INTRODUCTION Welcome to the Cabletron Systems WPIM-RT1 User’s Guide. This manual provides hardware information, and explains the use of Local Management to control and manage the Cabletron Systems WPIM-RT1. The WPIM-RT1 is installed in and provides full or fractional T1 to t...
Page 12 - Appendix B; FCC Part 68 - User’s Information; RELATED MANUALS
Introduction x WPIM-RT1 User’s Guide Appendix B , FCC Part 68 - User’s Information , explains the FCC Rules for the WPIM-RT1. RELATED MANUALS Refer to the manual included with the host platform in which the WPIM-RT1 is installed to supplement the procedures and other technical data provided in this ...
Page 13 - DOCUMENT CONVENTIONS; The following conventions are used throughout this document:; bold type; italic type
Introduction WPIM-RT1 User’s Guide xi DOCUMENT CONVENTIONS The following conventions are used throughout this document: NOTE Note symbol. Calls the reader’s attention to any item of information that may be of special importance. TIP Tip symbol. Conveys helpful hints concerning procedures or actions....
Page 14 - GETTING HELP; Your Cabletron Systems service contract number; xxx
Introduction xii WPIM-RT1 User’s Guide GETTING HELP For additional support related to this device or document, contact Cabletron Systems using one of the following methods: Before calling Cabletron Systems, have the following information ready: • Your Cabletron Systems service contract number • A de...
Page 15 - CHAPTER 1; Refer to
WPIM-RT1 User’s Guide 1-1 CHAPTER 1 OVERVIEW This chapter describes steps for operation of the WPIM-RT1. It also briefly explains WPIM-RT1 features, ISDN, and indicates where to find the WAN protocols supported by the WPIM-RT1. Some of the steps for successful operation of this device are: • Install...
Page 16 - WAN PROTOCOLS; Getting
Chapter 1: Overview 1-2 WPIM-RT1 User’s Guide 1.1 WPIM-RT1 FEATURES The WPIM-RT1 extends the functionality of the Wide Area Network host platform to provide a full or fractional T1 interface for the CSX400, HSIM-W6, or the HSIM-SSA710. The WPIM-RT1 provides a T1 interface that includes a built-in Ch...
Page 17 - CHAPTER 2; INSTALLING THE WPIM-RT1; Related; Introduction
WPIM-RT1 User’s Guide 2-1 CHAPTER 2 SETUP AND INSTALLATION The following information in this chapter details the set up and installation of the WPIM-RT1 into a host platform. 2.1 INSTALLING THE WPIM-RT1 Figure 2-1 WPIM-RT1 For additional support related to the WPIM-RT1, refer to the host platform ma...
Page 18 - Unpacking the WPIM-RT1; Getting Help; Installing the WPIM-RT1
Chapter 2: Setup and Installation 2-2 WPIM-RT1 User’s Guide 2.1.1 Unpacking the WPIM-RT1 1. Carefully remove the WPIM-RT1 from the shipping box. 2. Visually inspect the WPIM-RT1. If there are any signs of damage, contact Cabletron Systems immediately. Refer to Getting Help . 2.1.2 Pre-Installation T...
Page 19 - Secure the WPIM-RT1 to the three standoffs with the WPIM screws.; Reinstall the cover if applicable.; Do not connect the WAN cable at this point.
Installing the WPIM-RT1 WPIM-RT1 User’s Guide 2-3 4. Press down firmly on the WPIM-RT1 until the pins slide all the way into the connector. Ensure that the WPIM-RT1 seats flush on the standoffs. 5. Secure the WPIM-RT1 to the three standoffs with the WPIM screws. Figure 2-2 Installing the WPIM-RT1 2....
Page 20 - HOST PLATFORM LEDs; CONNECTING THE WAN CABLE TO THE WPIM-RT1
Chapter 2: Setup and Installation 2-4 WPIM-RT1 User’s Guide 2.2 HOST PLATFORM LEDs The host platform displays LED indications of the WPIM-RT1’s operation. For more information on LED indications, refer to the host platform manual. 2.3 REQUIRED MANAGEMENT OPERATIONS Before the WAN cable can be connec...
Page 21 - WAN Connection to the WPIM-RT1
Connecting the WAN cable to the WPIM-RT1 WPIM-RT1 User’s Guide 2-5 The RJ45 cable from the WPIM-RT1 must be plugged into the WAN connection wall jack (see Figure 2-3 , below). The cable is not supplied with the WPIM-RT1, but may be ordered separately from Cabletron Systems, cable part number 9372094...
Page 23 - CHAPTER 3; Arrow keys to move up, down, right or left within the screen.
WPIM-RT1 User’s Guide 3-1 CHAPTER 3 LOCAL MANAGEMENT This chapter explains how to configure the WPIM-RT1 through Local Management for T1 service on the CSX400 or the HSIM-W6. Refer to the Cabletron Systems HSIM-SSA710 User’s Guide for information on Local Management for the HSIM-SSA710. The WAN Phys...
Page 24 - THE WAN PHYSICAL CONFIGURATION SCREEN; WAN Physical Configuration Screen; WAN Physical Configuration Screen Fields; To select the WPIM you wish to configure, proceed as follows:
Chapter 3: Local Management 3-2 WPIM-RT1 User’s Guide 3.1 THE WAN PHYSICAL CONFIGURATION SCREEN To access the WAN Physical Configuration screen, use the arrow keys to highlight the WAN SETUP menu item, then press ENTER. The screen shown in Figure 3-1 displays. Figure 3-1 WAN Physical Configuration S...
Page 25 - Displays the number of the slot in which the WPIM resides.
The WAN Physical Configuration Screen WPIM-RT1 User’s Guide 3-3 2. Use the SPACE bar to select the appropriate WPIM, then press ENTER. The WAN Configuration screen automatically displays unique configuration fields for each WPIM as shown in Figure 3-1 . The WAN Physical Configuration screen displays...
Page 26 - WPIM Line Configuration Fields; are specific to the T1 mode of the
Chapter 3: Local Management 3-4 WPIM-RT1 User’s Guide 3.1.2 WPIM Line Configuration Fields The configuration fields displayed on the WAN Physical Configuration screen shown in Figure 3-1 are specific to the T1 mode of the WPIM-RT1. T1 Timeslot View (Toggle) Displays the status of the Timeslot Config...
Page 27 - WPIM Timeslot Configuration Table; Sample Timeslot Configuration
The WAN Physical Configuration Screen WPIM-RT1 User’s Guide 3-5 • 267-399 Ft • 400-533 Ft • 534-655 Ft T1 Loopback (Selectable) Network Loopback is a testing procedure that segments the line and allows the user to isolate faults. The selections for this field are None, Line-Loop, and Payload-Loop. I...
Page 28 - shows a sample configuration for three sites. Of the 24; Sample Configuration
Chapter 3: Local Management 3-6 WPIM-RT1 User’s Guide Figure 3-3 shows a sample configuration for three sites. Of the 24 Timeslots, Site #1 uses 16 to communicate with Site #2 and the remaining 8 to communicate with Site #3. This configuration varies tremendously depending on how the service provide...
Page 29 - THE WAN INTERFACE CONFIGURATION SCREEN; WAN Interface Configuration Screen; WAN Interface Configuration Screen Fields; Interface number utilized for the Protocol Manager chosen.
The WAN Interface Configuration Screen WPIM-RT1 User’s Guide 3-7 3.2 THE WAN INTERFACE CONFIGURATION SCREEN This section describes the features of the WAN Interface Configuration screen. Access the screen by using the arrow keys to highlight the WAN INT CONFIG command field at the bottom of the WAN ...
Page 30 - Frame Relay as the Protocol Manager
Chapter 3: Local Management 3-8 WPIM-RT1 User’s Guide Active Protocol (Read-Only) Displays the active OSI layer protocol (Protocol Manager) chosen for the WPIM-RT1. There is one set of parameters displayed for FR, and one set for PPP. Refer to Section 3.2.1.1 for information on the Active Protocol s...
Page 31 - PPP as the Protocol Manager
The WAN Interface Configuration Screen WPIM-RT1 User’s Guide 3-9 3.2.1.2 PPP as the Protocol Manager Figure 3-5 WAN Interface Configuration Screen (PPP) Refer to Figure 3-5 for the following parameters displayed for PPP. PPP MRU (Modifiable) Displays the Maximum Receive Units that PPP can handle, mo...
Page 32 - Command Fields and Interface Table Fields; Used to save the configuration changes.
Chapter 3: Local Management 3-10 WPIM-RT1 User’s Guide 3.2.1.3 Command Fields and Interface Table Fields SAVE (Command) Used to save the configuration changes. PORTS: [1-32] (Command) Interface table displays the range of circuits shown in the command field. The SPACE bar and either the BACKSPACE or...
Page 33 - FULL T1 CONFIGURATION USING PPP; using a CSX400 with a; Full T1 Configuration; The line configuration information shown in; Telco Configuration Information
Full T1 Configuration Using PPP WPIM-RT1 User’s Guide 3-11 3.3 FULL T1 CONFIGURATION USING PPP This section provides step-by-step instructions for configuring the WPIM-RT1 to use a full T1 circuit in a PPP environment. This simplified example assumes the setup shown in Figure 3-6 using a CSX400 with...
Page 34 - T1 Physical Configuration; Proceed with the following steps:; Use the arrow keys to highlight MgrType. Select PPP.
Chapter 3: Local Management 3-12 WPIM-RT1 User’s Guide 3.3.1 T1 Physical Configuration Begin the T1 configuration by accessing the WAN Physical Configuration screen through Local Management ( Figure 3-1 ). Access the WAN Physical Configuration screen from the WAN SETUP menu item in the host platform...
Page 35 - Proceed to; T1 Interface Configuration; and proceed with the
Full T1 Configuration Using PPP WPIM-RT1 User’s Guide 3-13 7. Use the arrow keys to highlight T1 TX Clock Source. Press the SPACE bar to select Local (no clock source provided by telephone company) or Loop (clock source provided by telephone company), then press ENTER. 8. Use the arrow keys to highl...
Page 36 - FRACTIONAL T1 CONFIGURATION USING PPP; using two CSX400s with; Fractional T1 Configuration
Chapter 3: Local Management 3-14 WPIM-RT1 User’s Guide 4. Use the arrow keys to highlight the SAVE command, then press ENTER. The message “SAVE DONE!” displays and Local Management saves the changes to memory. The WAN configuration is complete. It takes up to 60 seconds for the WAN Interface to come...
Page 38 - Proceed to the
Chapter 3: Local Management 3-16 WPIM-RT1 User’s Guide The following four steps are based on information supplied by the service provider. Consult the service provider for the correct settings. 5. Use the arrow keys to highlight T1 Line Coding. Use the SPACE bar to select B8ZS or AMI, then press ENT...
Page 39 - FRAME RELAY CONFIGURATION; using two CSX400s, each; Frame Relay Configuration
Frame Relay Configuration WPIM-RT1 User’s Guide 3-17 3.4.2 T1 Interface Configuration The WAN Interface Configuration screen is accessed through the WAN Physical Configuration screen. Access the WAN Interface Configuration screen by using the arrow keys to highlight the WAN INT CONFIG command and pr...
Page 40 - Frame Relay Physical Configuration
Chapter 3: Local Management 3-18 WPIM-RT1 User’s Guide The line configuration information shown in Table 3-3 must be supplied by the service provider. 3.5.1 Frame Relay Physical Configuration Begin the WPIM-RT1 physical configuration by accessing the WAN Physical Configuration screen through Local M...
Page 42 - Frame Relay Interface Configuration; Make any changes to the available settings as desired.
Chapter 3: Local Management 3-20 WPIM-RT1 User’s Guide 3.5.2 Frame Relay Interface Configuration Access the WAN Interface Configuration screen through the WAN Physical Configuration screen, by using the arrow keys to highlight the WAN INT CONFIG command, then press ENTER. Proceed with the following ...
Page 45 - APPENDIX A; PHYSICAL PROPERTIES
WPIM-RT1 User’s Guide A-1 APPENDIX A SPECIFICATIONS This appendix provides operating specifications and cabling information for the Cabletron Systems WPIM-RT1. Cabletron Systems reserves the right to change these specifications at any time without notice. A.1 PHYSICAL PROPERTIES A.2 ENVIRONMENTAL RE...
Page 46 - T1 INTERFACE CABLING; lists Cabletron Systems part numbers for the interface cables. A; Cable Assemblies and Pinouts; Cabletron T1 Cable Part Numbers
Appendix A: Specifications A-2 WPIM-RT1 User’s Guide A.4 T1 INTERFACE CABLING Table A-1 lists Cabletron Systems part numbers for the interface cables. A standard 20-foot cable is available or the length of cable may be specified when ordering. A.4.1 Cable Assemblies and Pinouts The following section...
Page 47 - APPENDIX B; Port ID
WPIM-RT1 User’s Guide B-1 APPENDIX B FCC PART 68 - USER’S INFORMATION The following instructions are provided to ensure compliance with the Federal Communications Commission (FCC) Rules, Part 68. 1. This device must only be connected to the ISDN Basic Rate network behind an FCC Part 68 registered ch...
Page 48 - The attached affidavit must be completed by the installer.
Appendix B: FCC Part 68 - User’s Information B-2 WPIM-RT1 User’s Guide 5. Under the FCC Rules, no customer is authorized to repair this equipment. This restriction applies regardless of whether the equipment is in or out of warranty. 6. If the telephone company alters their equipment in a manner tha...
