Page 3 - NOTICE; FCC NOTICE
HSIM-G01/G09 User’s Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware...
Page 8 - Notice
Page 9 - vii; CONTENTS
HSIM-G01/G09 User’s Guide vii CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Manual ....................................................................... 1-2 1.2 Document Conventions ............................................................... 1-2 1.3 Getting Help..................................
Page 11 - Welcome to the Cabletron Systems
HSIM-G01/G09 User’s Guide 1-1 CHAPTER 1 INTRODUCTION Welcome to the Cabletron Systems HSIM-G01/G09 User’s Guide . This manual describes the HSIM-G01 and HSIM-G09 and provides information concerning features, installation, troubleshooting, the use of Local Management, and specifications. A general wo...
Page 12 - USING THIS MANUAL; Chapter 1; Introduction; Chapter 2; Installation; Chapter 3; LANVIEW LEDs; Chapter 4; Local Management; Appendix A; Specifications; DOCUMENT CONVENTIONS; Note; Caution
Chapter 1: Introduction 1-2 HSIM-G01/G09 User’s Guide 1.1 USING THIS MANUAL Read through this manual completely to familiarize yourself with its content and to gain an understanding of the features and capabilities of the HSIM-G. The following list provides an overview of each section of this manual...
Page 13 - Getting Help; GETTING HELP; Your Cabletron Systems service contract number
Getting Help HSIM-G01/G09 User’s Guide 1-3 1.3 GETTING HELP For additional support related to this device or document, contact Cabletron Systems using one of the following methods: Before calling Cabletron Systems, have the following information ready: • Your Cabletron Systems service contract numbe...
Page 14 - OVERVIEW; Connectivity; The HSIM-G only operates in full duplex mode.; LANVIEW Diagnostic LEDs; RELATED DOCUMENTATION
Chapter 1: Introduction 1-4 HSIM-G01/G09 User’s Guide 1.4 OVERVIEW The HSIM-G extends the functionality of certain Cabletron Systems interface modules or standalone devices by providing high-speed uplink capability through Gigabit Ethernet technology. Section 1.4.1 and Section 1.4.2 give information...
Page 15 - To install the HSIM-G you need the following items:; Only qualified personnel should install or service this unit.; specification. The network installation
HSIM-G01/G09 User’s Guide 2-1 CHAPTER 2 INSTALLATION To install the HSIM-G you need the following items: • Antistatic wrist strap • Phillips screwdriver 2.1 UNPACKING THE HSIM-G Unpack the HSIM-G as follows: 1. Remove the shipping box material covering the HSIM-G. 2. Carefully remove the module from...
Page 16 - Installing an HSIM-G in an Interface Module
Chapter 2: Installation 2-2 HSIM-G01/G09 User’s Guide 2.2 INSTALLING AN HSIM-G You can install an HSIM-G in any Cabletron Systems device that supports HSIM technology (e.g., 2E42-27, 6E132-25). The following sections provide instructions for installing an HSIM-G in an interface module or in a standa...
Page 17 - Removing the HSIM Coverplate; Refer to
Installing an HSIM-G HSIM-G01/G09 User’s Guide 2-3 Figure 2-1 Removing the HSIM Coverplate 7. Refer to Figure 2-2 and place the HSIM-G behind the module faceplate. 8. Align the HSIM connector of the HSIM-G with the HSIM pins on the module. 9. Press down firmly on the back of the HSIM-G until the con...
Page 18 - Chapter 2: Installation; Reinstall the interface module in the chassis.; Installing the HSIM-G
Chapter 2: Installation 2-4 HSIM-G01/G09 User’s Guide 10. Secure the HSIM-G to the module faceplate using the mounting screws saved in step 5. 11. Secure the HSIM-G to the module standoffs using the standoff screws saved in step 6. 12. Reinstall the interface module in the chassis. 13. Reattach the ...
Page 19 - Installing an HSIM-G in a Standalone Device
Installing an HSIM-G HSIM-G01/G09 User’s Guide 2-5 2.2.2 Installing an HSIM-G in a Standalone Device To install an HSIM-G into a standalone device (e.g., 2E42-27), perform the following steps: 1. Power down the device and remove the power cord. 2. Disconnect any cables connected to the network ports...
Page 20 - CONNECTING TO THE NETWORK; HSIM-G Port Designations
Chapter 2: Installation 2-6 HSIM-G01/G09 User’s Guide 11. Secure the HSIM-G to the module standoffs using the standoff screws saved in step 6. 12. Reattach the chassis cover to the standalone device, reconnect the power cord, and reconnect the standalone device to the network. 2.3 CONNECTING TO THE ...
Page 21 - Connecting to the Network; HSIM-G Network Connection; before following this procedure.
Connecting to the Network HSIM-G01/G09 User’s Guide 2-7 2.3.1 HSIM-G Network Connection To connect the HSIM-G01 using multimode and single mode fiber, and the HSIM-G09 using single mode fiber to the network, perform the following steps: 1. Remove the protective fiber port covers from the fiber optic...
Page 22 - Fiber Connections; SC Connector
Chapter 2: Installation 2-8 HSIM-G01/G09 User’s Guide Figure 2-4 Fiber Connections 3. At the other end of the fiber optic cable, attach the SC connector to the other device. 4. Verify that a link exists by checking that the link (LNK) LED is ON (solid green), the port receive (RX) LED is ON (flashin...
Page 23 - HSIM-G09 Connection Using Multimode Cable; Launch Mode Conditioning Cable Connection for the HSIM-G09
Connecting to the Network HSIM-G01/G09 User’s Guide 2-9 To remove the SC connector, from the HSIM-G, carefully pull the connector out of the port. It may need to be wiggled gently to release the latching keys. If a link has not been established, refer to Chapter 3 before contacting Cabletron Systems...
Page 25 - shows the
HSIM-G01/G09 User’s Guide 3-1 CHAPTER 3 LANVIEW LEDs This chapter describes how to use the LANVIEW LEDs to monitor the status of the HSIM-G and diagnose problems. Figure 3-1 shows the location of the HSIM-G LEDs. Figure 3-1 HSIM-G LANVIEW LEDs Transmit (TX) Receive (RX) Link (LNK) 2398_leds HSIM-G L...
Page 26 - The terms flashing, blinking, and solid used in; indicate the following:; Flashing indicates an irregular LED pulse.; LED
Chapter 3: 3-2 HSIM-G01/G09 User’s Guide Table 3-1 HSIM-G LEDs NOTE The terms flashing, blinking, and solid used in Table 3-1 indicate the following: Flashing indicates an irregular LED pulse. Blinking indicates a steady LED pulse. (approximately 50% on, 50% off) Solid indicates a steady LED light. ...
Page 27 - The HSIM-G is installed in the host platform.; NAVIGATING LOCAL MANAGEMENT SCREENS; shows a typical hierarchy of screens that you; for details on; is only an example of how the HSIM-G screen may
HSIM-G01/G09 User’s Guide 4-1 CHAPTER 4 LOCAL MANAGEMENT This chapter provides information on the HSIM-G screens accessible via the Local Management of the host platform. One Local Management screen is specific to the HSIM-G, which is detailed in this chapter. All other screens are detailed in the L...
Page 28 - Chapter 4: Local Management; Typical Hierarchy of Local Management Screens; GIGABIT ETHERNET CONFIGURATION SCREEN; ) displays the type of interface used
Chapter 4: Local Management 4-2 HSIM-G01/G09 User’s Guide Figure 4-1 Typical Hierarchy of Local Management Screens 4.2 GIGABIT ETHERNET CONFIGURATION SCREEN The Gigabit Ethernet Configuration screen allows the user to support the HSIM-G01 and the HSIM-G09. The screen (see Figure 4-2 ) displays the t...
Page 29 - Gigabit Ethernet Configuration Screen; Port
Gigabit Ethernet Configuration Screen HSIM-G01/G09 User’s Guide 4-3 Figure 4-2 Gigabit Ethernet Configuration Screen The following defines each field of the Gigabit Ethernet Configuration screen. Port X (Read-Only) The port or interface number on the host platform in which the HSIM-G is installed. P...
Page 30 - describes how to configure a port with an; Configuring the HSIM-G Port
Chapter 4: Local Management 4-4 HSIM-G01/G09 User’s Guide Current Oper. Mode (Read-Only) Displays the current operating mode of the port. Regardless of whether an HSIM-G01 or HSIM-G09 is installed, this field displays 1000Base-XFD. Desired Oper. Mode (Toggle) Allows the user to select the desired op...
Page 31 - Setting the Operational Mode; Use the arrow keys to highlight the Desired Oper. Mode field.; Setting the Advertised Ability; Use the SPACE bar to select Enabled or Disabled. Press ENTER.
Gigabit Ethernet Configuration Screen HSIM-G01/G09 User’s Guide 4-5 4.2.1.1 Setting the Operational Mode Use the Desired Oper. Mode field to set the active technology. This field steps between Auto-Negotiation and 1000Base-XFD. If Auto-Negotiation is selected, the HSIM-G automatically sets the activ...
Page 33 - below. To use multimode fiber with the; GIGABIT ETHERNET SPECIFICATIONS; HSIM-G01 Optical Specifications
HSIM-G01/G09 User’s Guide A-1 APPENDIX A SPECIFICATIONS This appendix lists the specifications and regulatory requirements for the HSIM-G01 and HSIM-G09. Cabletron Systems reserves the right to change these specifications at any time without notice. The HSIM-G01 and HSIM-G09 are both fiber optic dev...
Page 34 - Appendix A: Specifications; GPIM-09 Operating Range; HSIM-G01 Operating Range; Meters
Appendix A: Specifications A-2 HSIM-G01/G09 User’s Guide A.1.2 HSIM-G09 Specifications (1000Base-LX) Table A-4 GPIM-09 Operating Range A. In order to obtain the distance of 550 m for the GPIM-09 using multimode fiber, Launch Mode Conditioning cable must be used. Refer to Section 2.3.2 for details. T...
Page 35 - Physical Properties; PHYSICAL PROPERTIES; Dimensions; Safety
Physical Properties HSIM-G01/G09 User’s Guide A-3 A.2 PHYSICAL PROPERTIES A.3 ENVIRONMENTAL REQUIREMENTS A.4 REGULATORY COMPLIANCE This equipment meets the following safety and electromagnetic compatibility (EMC) requirements: Dimensions 3.18H x 16.51W x 29.21D (cm)1.25H x 6.5W x 11.5D (in) Weight 2...
