Cabletron Systems FPIM-02 - Manual

v Contents Chapter 1 Introduction Features........................................................................................................................... 1-1Related Manuals ............................................................................................................ 1-4Get...

1-1 Chapter 1 Introduction The 9M426-02 SmartSwitch Module shown in Figure 1-1, is a three port switch module with two front panel HSIM interfaces and one INB-2 backplane interface. With the proper HSIM, this module may be used as an ATM uplink for the SmartSwitch 9000 chassis. Features Processor Th...

Introduction 1-4 Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual. SmartSwitch 9000 Installation Guide SmartSwitch 9000 9C300-1 Environmental Module User ’s Guide SmartSwitch 9000 9C214-1 AC Power Supply User ’s Guide IN...

2-1 Chapter 2 Installing the SmartSwitch 9000 Module This module uses HSIMs for the front panel connections. They are not shipped with the module and must be purchased separately. For installation information, refer to the manual supplied with the HSIM. Unpacking the Module 1. Carefully remove the m...

2-3 Installing the SmartSwitch 9000 Module An eight position DIP switch is located on the module card as shown in Figure 2-1. The function of the switches are listed in Table 2-1. See the Cautions at the end of this table. Table 2-1. Function of DIP Switch Switch Function Description 8 Clear Passwor...

Installing the SmartSwitch 9000 Module 2-6 The Reset Switch The Reset switch is located under the top plastic tab as shown in Figure 2-3.Use the reset switch to reset the module’s processor, shutdown (power down) the module, and/or restart the module. • To reset the module’s i960 processor, press th...

3-1 Chapter 3 Operation The 9M426-02 FDDI SmartSwitch Module is a three port switch module with two front panel HSIM interfaces and one INB-2 backplane interface. This module, with the proper HSIM, may be used for an FDDI, ATM, WAN and other high-speed connectivity for the SmartSwitch 9000 chassis. ...

Operation 3-2 band from user data. Modules which share the SMB-10 bus periodically send out loop-back packets to ensure the validity of SMB-10. In the event a fault is detected on the SMB-10, the SMB-1 can be used as an alternate communication channel by the modules. System Diagnostic Controller Thi...

4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figure 4-1 is the LANVIEW LEDs of the 9M426-02 module. Figure 4-1. The LANVIEW LEDs 9 9 M M 4 4 2 2 6 6 -- 0 0 2 2 S S M M B B C C P P U U II N N B B Syste...

5-1 Chapter 5 Specifications Technical Specifications CPU Intel i960 RISC based microprocessor Memory 4 Meg. Flash Memory (expandable to 8 Meg.)16 Meg. DRAM (expandable to 32 Meg.) Network Interface Cabletron HSIMs Safety This equipment meets the safety requirements of: • UL 1950 • CSA C22.2 No. 950...

Specifications 5-2 • EMC requirements of: EN 50082-1IEC 801-2 ESDIEC 801-3 Radiated susceptibilityIEC 801-4 EFT Service MTBF (MHBK-217E) >200,000 hrs. MTTR <0.5 hr. Physical Dimensions 35.0 D x 44.0 H x 6.0 W centimeters(13.8 D x 17.4 H x 2.4 W inches) Weight Unit: 2.6 kg. (6lb) Shipping: 3.6 ...