Cabletron Systems 9T101-04 - Manual

v Contents Chapter 1 Introduction Features........................................................................................................................... 1-1Related Manuals ............................................................................................................ 1-4Get...

1-1 Chapter 1 Introduction The 9T101-04 Token Ring Router module, shown in Figure 1-1, is a four port Token Ring router. Up to four front panel network connections can be made to this module and they can be routed to any other port and to any other MMAC-Plus module via the FNB bus. Features Processo...

Introduction 1-4 Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual. MMAC-Plus Installation Guide MMAC-Plus Operations Guide MMAC-Plus 9C300-1 Environmental Module User ’s Guide MMAC-Plus 9C214-1 AC Power Supply User ’s Gu...

2-1 Chapter 2 Installing the MMAC-Plus Module The MMAC-Plus module may be installed into any of the 14 slots that are available. To install, follow the steps below: 1. Remove the blank panel, covering the slot that the module is being mounted in. All other slots must be covered, if modules are not b...

2-3 The Reset Switch The Reset Switch The Reset switch is located on the front panel, under the top plastic tab, as shown in Figure 2-2. It serves two functions: • Pressing the Reset switch twice within three seconds causes the processor to reset. • Pressing and holding the switch on for three or mo...

3-1 Chapter 3 Operation The 9T101-04 Token Ring Router module is a four port router. Four front panel network connections can be made to this module and they can be routed to any other port and to any other MMAC-Plus module via the FNB bus. Figure 3-1. 9T101-04 Block Diagram Token Ring port CPU Toke...

Operation 3-2 Flexible Network Bus (FNB) The FNB consists of two dual FDDI networks, the FNB-1 and FNB-2, providing up to 400 Mbps of data bandwidth. These FDDI networks are 100% ANSI FDDI-compliant, supporting SMT (version 7.3), MAC, PHY, and PMD standards. This allows the FNB to traverse multiple ...

3-3 FNB Interface FNB Interface MMAC-Plus modules are designed with one of two attachment policies. One allows dual attachment of a module to either FNB-1 or FNB-2; the second allows dual attachment to both FNB-1 and FNB-2. The 9T101-04 has one dual attachment to the FNB backplane, connecting to eit...

4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs, shown in Figure 4-1, indicate the status of the module and may be used as an aid in troubleshooting. Figure 4-1. LANVIEW LEDs FDDI FNB SMB CPU AUX CON 9T101-04 IN-RING A IN-RING B IN-RING A IN-RING B 16 Mb 16 Mb 16 MB 16 Mb 1 2 System Status F...

5-1 Chapter 5 Specifications Safety This equipment meets the following safety requirements: • UL 1950 • CSA C22.2 No. 950 • EN 60950 • IEC 950 • EMI Requirements of FCC Part 15 Class A • EN 55022 Class A • VCCI Class I • EMC the following requirements: EN 50082-1IEC 801-2 ESDIEC 801-3 Radiated susce...

Specifications 5-2 Physical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters(13.8 D x 17.4 H x 1.2 W inches) Weight Unit: 1.36 kg. (3 lb) Shipping: 1.81 kg. (4 lb) Environment Operating Temperature 5 to 40 ° C Storage Temperature -30 to 90 ° C Relative Humidity 5% to 95% non-condensing