Page 2 - Notice; NOTICE; LANVIEW
Notice i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or soft...
Page 3 - FCC NOTICE; This equipment has been tested and found to comply with; DOC NOTICE
Notice ii FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOT...
Page 4 - VCCI NOTICE; Read the instructions for correct handling.
Notice iii VCCI NOTICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment (VCCI) aimed at preventing radio interfe...
Page 5 - CONTENTS; CHAPTER 1 INTRODUCTION
v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL ......................................................................... 1-11.2 THE 7F06-02 MODULE ........................................................................... 1-2 1.2.1 Cable Type and FPIMs ........................................
Page 6 - Contents
vi Contents 5.7 PHYSICAL ................................................................................................5-2 5.7.1 Dimensions .....................................................................................5-25.7.2 Weight ............................................................
Page 7 - F06-02 FDDI SmartSwitch Interface; USING THIS MANUAL; Introduction
1-1 CHAPTER 1 INTRODUCTION Welcome to Cabletron Systems 7F06-02 FDDI SmartSwitch Interface Module User’s Guide . This guide is a simple reference for installing and using the 7F06-02 Module. Before installing this module, you should carefully read through this manual to gain a full understanding of ...
Page 8 - INTRODUCTION
1-2 INTRODUCTION 1.2 THE 7F06-02 MODULE The 7F06-02 Module provides two Fiber Optic ports via front panel FPIM modules. 1.2.1 Cable Type and FPIMs The 7F06-02 module has two front panel connectors that interface to the 7X00 Smart Switch Module through the chassis backplane. The front panel connectio...
Page 11 - X00 SmartSwitch Control Module User’s Guide
INTRODUCTION 1-5 1.4 RELATED MANUALS The manuals listed below should be used to supplement the procedures and other technical data provided in this manual. The procedures will be referenced, where appropriate, but will not be repeated. 7X00 SmartSwitch Control Module User’s Guide 7F06-02 Local Manag...
Page 12 - Appendix A; FPIM MODULE SPECIFICATIONS
2-1 CHAPTER 2 NETWORK REQUIREMENTS Before installing Cabletron Systems 7F06-02 Module, review the network requirements outlined in this chapter. All requirements included in this chapter should be met to ensure satisfactory performance of the 7F06-02 Module. Failure to do so may result in unsatisfac...
Page 13 - NETWORK REQUIREMENTS; Transmitter power parameters are listed in Table 2-2.; Table 2-2. Transmitter Power Parameters; fiber
2-2 NETWORK REQUIREMENTS Transmitter power parameters are listed in Table 2-2. The link distance is up to 2 kilometers on the multimode fiber-optic cable as specified by ANSI MMF-PMD. Table 2-2. Transmitter Power Parameters Parameter Typical Value Worst Case Worst Case Budget Typical Budget 50/125 µ...
Page 14 - Pin Number; NA
NETWORK REQUIREMENTS 2-3 2.1.2 FPIM-02 and FPIM-04 The FPIM-02 has an RJ-45 connector supporting an Unshielded Twisted Pair (UTP) connection. The FPIM-04 has an RJ-45 connector supporting a Shielded Twisted Pair (STP) connection. The pinouts for both are listed in Table 2-3. The link distance is up ...
Page 15 - Parameter; Spectral Width; Better
2-4 NETWORK REQUIREMENTS 2.1.3 FPIM-05 and FPIM-07 The FPIM-05 and FPIM-07 provide a Single-mode fiber connection. The FPIM-05 uses a MIC style connector and the FPIM-07 uses an SC type connector. The specifications for both devices are listed in Table 2-4. The link distance is up to 40 kilometers (...
Page 17 - Installing in the 7C03 SmartSwitch
3-2 INSTALLATION/REMOVAL Figure 3-1. Installing an FPIM 3.3 INSTALLING/REMOVING THE 7F06-02 MODULE The following procedure detail the installing and removal procedure for the 7F06-02 module. 3.3.1 Installing in the 7C03 SmartSwitch The 7F06-02 Module is installed in the 7C03 MMAC SmartSwitch using t...
Page 18 - C03 MMAC SmartSwitch
INSTALLATION/REMOVAL 3-3 Notes: The left most slot in the 7C03 MMAC SmartSwitch is reserved for the 7X00 SmartSwitch Module. Before installing the 7F06-02 module, attach the wrist strap included with the SmartSwitch or SmartSwitch module by following the instructions printed on the package. 1. Remov...
Page 19 - SmartSwitch; Screws
3-4 INSTALLATION/REMOVAL Note: Before removing the 7F06-02 module, attach the wrist strap included with the SmartSwitch or SmartSwitch module by following the instructions printed on the package. 1. Use a slotted screwdriver to loosen the two screws that secure the module to the chassis. 2. Locate t...
Page 20 - Using a slotted screwdriver, tighten the top and bottom screws.
INSTALLATION/REMOVAL 3-5 3.3.3 Installing in the 7C04 or 7C04-R Workgroup SmartSwitch The 7F06-02 Module is installed in the 7C04 or 7C04-R Workgroup SmartSwitch using the following steps and referring to the appropriate figure. Notes: The top slot in the 7C04 Workgroup SmartSwitch is reserved for t...
Page 22 - module to the chassis.
INSTALLATION/REMOVAL 3-7 3.3.4 Removing from the 7C04 or 7C04-R Workgroup SmartSwitch The 7F06-02 Module, inserted in the 7C04 or the 7C04-R Workgroup SmartSwitch, can be removed whenever necessary. Follow the steps below and refer to the appropriate figure to remove the module. Note: Before removin...
Page 23 - Ejector Tabs
3-8 INSTALLATION/REMOVAL Figure 3-7. Removing the 7F06-02 Module from the 7C04-R Workgroup SmartSwitch FANS SN 4 3 2 1 Ejector Tabs Screws
Page 24 - A Link Status
4-1 CHAPTER 4 TROUBLESHOOTING The 7F06-02 Module uses LANVIEW, Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIEW LEDs the status of each transmit and receive port on the 7F06-02 Module can be determined, at a glance. This section discusses the function and purpo...
Page 25 - TROUBLESHOOTING; Table 4-1 indicates the state of the receive port.; Off; Off
4-2 TROUBLESHOOTING Table 4-1 indicates the state of the receive port. Table 4-2 indicates the state of the transmit port. Table 4-1. Port Receive LEDs LED Color State Yellow (Flashing) Data activity (flashing to steady on indicates rate) Off No activity, port can be disabled or enabled Table 4-2. P...
Page 26 - State
TROUBLESHOOTING 4-3 Table 4-3 indicates the state of the A/B Link LEDs. Table 4-3. Link LEDs A p S B State Green N/A N/A Green Ports Enabled & Active Green Green Off Green THRU A, MAC on Primary, Secondary Bypasses Board Green Green Yellow Green THRU A, MAC on Primary,No MAC on Secondary Green O...
Page 28 - TECHNICAL SPECIFICATIONS; This equipment meets the safety requirements of:
5-2 TECHNICAL SPECIFICATIONS 5.5 SAFETY It is the responsibility of the person who sells the system to which the module will be a part to ensure that the total system meets allowed limits of conducted and radiated emissions. This equipment meets the safety requirements of: • UL 1950 • CSA C22.2 No. ...
