Bush Hog TDR-11 - Manual - manualsarea.com

Page 3 - TDR-11 Finishing Mower; TABLE OF CONTENTS; RETAIL CUSTOMER’S RESPONSIBILITY; SECTION/PARA PAGE

TDR-11 Finishing Mower TABLE OF CONTENTS SECTION/PARA PAGE Warranty.................................................2Dealer Preparation Check List ...............3Safety Precautions .................................4Federal Laws and Regulations ..............6 I. INTRODUCTION & DESCRIPTION ........

Page 4 - BUSH HOG; LIMITED WARRANTY; DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

BUSH HOG ® LIMITED WARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a periodof one (1) year for non-commercial, sta...

Page 5 - DEALER PREPARATION CHECK LIST; Tri-Deck Finishing Mower

DEALER PREPARATION CHECK LIST Tri-Deck Finishing Mower T D R - 1 1 BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. ❒ 1. Assembly completed. ❒ 2. Gearboxes filled with oil. ❒ 3. All fittings lubricated. ❒ 4. All shields in place and in g...

Page 6 - Signal Words

Safety Alert Symbol This Safety Alert Symbol means: “ATTENTION! BECOME ALERT!YOUR SAFETY IS INVOLVED!” This symbol is used to call attention to safetyp r e c a u t i o n s t h a t s h o u l d b e f o l l o w e d b y t h eoperator to avoid accidents. When you see thissymbol, carefully read the messag...

Page 7 - IMPORTANT SAFETY PRECAUTIONS

IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe-ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in death...

Page 8 - IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING; EMPLOYEE TRACTOR OPERATING INSTRUCTIONS:

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as ...

Page 9 - Technical Specifications

SECTION I INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus-tomer. Your TDR-11 Finishing Mower has beencarefully designed to give maximum service withminimum down time. This manual is provided to givey o u t h e n e c e s s a r y o p e r a t i n g a n d m a i...

Page 10 - -1 ATTACHING TO TRACTOR; SECTION II

2-1 ATTACHING TO TRACTOR IMPORTANT (540 RPM only) The minimum required PTO horsepower is 30 HP for the TDR-11. A. Adjust tractor drawbar length to dimension shown in Figure 2-1. Incorrect drawbar length willchange angle of driveline causing possible damageto constant velocity joint. See tractor oper...

Page 11 - -2 CUTTING HEIGHT ADJUSTMENT

F. Route control chain to convenient location andfasten to tractor. Be sure excess slack is removedfrom the chain to avoid entanglement with tractortires or other moving parts. Make sure latch lockingpins are in the stored positions so that latches can be released by pulling the chain.(Refer to Figu...

Page 13 - -1 MAINTENANCE CHECK LIST

SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below.Lower implement to ground, turn off tractor, and setparking brake before doing maintenance inspectionsor work. All bolts should be torqued as indicated intorque chart unless otherwise indicated. BEFORE ...

Page 15 - -5 BLADE REPLACEMENT

4-5 BLADE REPLACEMENT A. Raise cutter using tractor hydraulic system and use transport locks before changing blades. B. Turn off tractor,set parking brake and remove key. WEAR HEAVY WORK GLOVES TO PRO-T E C T H A N D S F R O M S H A R P E D G E S .WHEN TURNING BLADES, BE AWAREOF OPPOSITE BLADE APPRO...

Page 16 - SAFETY DECALS

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, providesafety decals for any of our products in the field at no charge. Contact...

Page 17 - DECALS CONTINUED

Page 18 - TORQUE SPECIFICATIONS; METRIC

TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 1...

Bush Hog TDR-11 - Manual

Table of Contents:

Summary

Other Bush Hog Models