Bush Hog GHM 800 - Manual - manualsarea.com

Page 3 - GHM HAY MOWER; TABLE OF CONTENTS; SECTION/PARA PAGE; RETAIL CUSTOMER’S RESPONSIBILITY; UNDERSTAND SIGNAL WORDS

GHM HAY MOWER TABLE OF CONTENTS SECTION/PARA PAGE Warranty.......................................................3 Dealer Preparation Check List .....................4Safety Precautions .......................................5Federal Laws and Regulations ....................6 I. INTRODUCTION & D...

Page 4 - BUSH HOG; LIMITED WARRANTY; DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

BUSH HOG ® LIMITED WARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a periodof one (1) year for non-commercial, sta...

Page 5 - DEALER PREPARATION CHECK LIST

DEALER PREPARATION CHECK LIST GHM HAY MOWER BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. ❒ 1. Assembly completed. ❒ 2. Gearbox filled with oil. ❒ 3. All fittings lubricated. ❒ 4. All shields in place and in good condition. ❒ 5. All f...

Page 6 - IMPORTANT SAFETY PRECAUTIONS

IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe-ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serio...

Page 7 - IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING; EMPLOYEE TRACTOR OPERATING INSTRUCTIONS:

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as ...

Page 9 - NARROW

SECTION II PREPARATION FOR USE TO AVOID SERIOUS INJURY OR DEATHN E V E R S T A N D B E T W E E N T R A C T O RAND MOWER WHILE TRACTOR IS BEINGBACKED TO HITCH. TO AVOID SERIOUS INJURY OR DEATHA D D I T I O N A L T R A C T O R F R O N T B A L -L A S T M A Y B E N E E D E D F O R S T A B L EO P E R A T...

Page 13 - SECTION IV; -1 MAINTENANCE CHECK LIST

3-7 CUTTER BAR HELPER SPRING ADJUSTMENT (9’ MODELS ONLY) The 9’ models are equipped with a helper springassembly to transfer cutter bar weight from theouter end of the cutter bar back to the frameassembly. The recommended minimum adjustmentmeasurement is 5-1/2” from under the bolt head tothe end of ...

Page 19 - FORWARD

Figure 4-12 Cutter Bar Arrangement and Blade Rotation NOTE The blades of adjacent oval discs must be 90° apart from oneanother as shown above to ensure proper timing. 9’ MAIN GEARBOX 8’ MAIN GEARBOX 7’ MAIN GEARBOX FORWARD #1 #2 #2 #2 #3 #3 #3 #4 #4 #4 #5 #5 #5 #6 #6 #7 CW CW CCW CW CCW CW CW CCW #1...

Page 22 - SAFETY DECALS

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, providesafety decals for any of our products in the field at no charge. Contact...

Page 24 - TORQUE SPECIFICATIONS; METRIC

TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 1...

Bush Hog GHM 800 - Manual

Table of Contents:

Summary

Other Bush Hog Models