Bush Hog ATH 900 - Manuals - manualsarea.com

Page 3 - ATH 900 FINISHING MOWER; Operator’s Manual; TABLE OF CONTENTS; PAGE; RETAIL CUSTOMER’S RESPONSIBILITY

ATH 900 FINISHING MOWER Operator’s Manual TABLE OF CONTENTS SECTION/PARA PAGE Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .2Dealer Preparation Check List . . . . . . . . .3Safety Precautions . . . . . . . . . . . . . . . . . .4Federal Laws and Regulations . . . . . . . . .5 I INTRODUC...

Page 4 - LIMITED WARRANTY; DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES; OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO

LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a periodof one (1) year for non-commercial, state and muni...

Page 6 - IMPORTANT SAFETY PRECAUTIONS

IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safetyprecautions that should be followed by theoperator to avoid accidents. When you see thissymbol, carefully read the message that fol-lows and heed its advice. Failure to complywith safety precautions could result in death ors...

Page 7 - IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING; EMPLOYEE TRACTOR OPERATING INSTRUCTIONS:

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as ...

Page 8 - Horsepower Range; SECTION I

6 Figure 1 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus-tomer. Your Air Turf Hog Series Rotary Cutter hasbeen carefully designed to give maximum servicewith minimum down time.This manual is provided togive you the necessary operating and maintenanceinstructions for keeping your rota...

Page 9 - -1 ATTACHING TO TRACTOR; SECTION II

2-1 ATTACHING TO TRACTOR A. Attach to tractor Cat. I three point hitch as described in tractor operator’s manual. SECTION II PREPARATION FOR USE B. Raise and lower cutter to determine position with shortest distance between the tractor PTO shaftand gearbox input shaft. Shut down tractor leavingcutte...

Page 11 - -2 CUTTING HEIGHT ADJUSTMENT

SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’smanual and tractor operator’s manual should oper-ate this machine. Operator should wear hard hat,s a f e t y g l a s s e s a n d s a f e t y s h o e s . T h e o p e r a t o rshould read, understa...

Page 12 - -1 MAINTENANCE CHECK LIST

SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below.Lower implement to ground, turn off tractor, and setparking brake before doing maintenance inspectionsor work. Some checks may require raising machineoff ground and supporting with blocks. All boltsshou...

Page 13 - -5 BLADE REPLACEMENT

40 HOURS 7. Spindle Assembly - Apply multi-purpose grease with grease gun until grease purges out top seal.Grease fittings for spindles should be accessed byremoving the plastic plugs in the shields. After com-pleting lubrication, replace plastic plugs.(Figure 4-1C) 4-3 BELT ADJUSTMENT Belt tension ...

Page 15 - -1 BASE UNIT ASSEMBLY

T H E F O L L O W I N G S A F E T Y P R E C A U T I O N SS H O U L D B E T H O R O U G H L Y U N D E R S T O O DBEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet,hands, lungs and head when assembling the equip-ment....

Page 17 - SAFETY DECALS

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, providesafety decals for any of our products in the field at no charge. Contact...

Page 18 - TORQUE SPECIFICATIONS; METRIC

BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37) 9/16 3/8 - 16 UNC 20 (27) 31 (42) 44 (6...