Bush Hog RTS - Manual

IMPORTANT SAFETY PRECAUTIONS In addition to the design and configuration of equipment, hazard control and accident prevention are depen-dent upon the awareness, concern, prudence and proper training of personnel in the operation, transport, maintenance and storage of equipment. Lack of attention to ...

SECTION II PREPARATION FOR USE 2-1 ATTACHING TO TRACTOR A. Attach tiller to tractor 3-point hitch per tractor operator’s manual. Do not attach driveline at thistime. NOTE Due to the many variations in tractor/implement hitchpoints and corresponding differences in distancesbetween tractor PTO shafts ...

8 26-7/8” Figure 2-7 Alternate Hitch Lug Mounting Figure 2-6 Hitch Lug Dimension Clamp Bolts Frame Hitch Pin Brackets Gearbox Input Shaft 26-7/8” H. Using cut off section of shield as a guide, cut shaft the same amount. (Figure 2-4) Figure 2-4 I. Repeat steps “G” and “H” to other driveline section. ...

9 Figure 3-1Skid Adjustment 1” 2” 3” 4” SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’sm a n u a l s h o u l d o p e r a t e t h i s m a c h i n e . O p e r a t o rshould wear hard hat, safety glasses, and safetyshoes. The operator should rea...

E . P l a c e t r a c t o r i n g e a r a n d p r o c e e d f o r w a r d .Increase speed to 3/4 throttle. Lower tiller into soil.Increase speed to 540 PTO rpm. Average soil withreasonable moisture will allow travel speeds up to 2mph. Hard soil will require low travel speed, lessthan 1 mph to ensure...

12 Figure 4-2 Blade Wear Figure 4-3 Shear Bolt Figure 4-4 Spring Length Spring Length Bondioli & Pavesi or Binacchi 1.12” (28.6 mm) EG/Comer 1.25” (31.8 mm) Figure 4-5 Slip Clutch Identification Bondioli & Pavesi EG or Binacchi (Holes Through Center) (Solid Casting) 4-6 SLIP CLUTCH ADJUSTMEN...

Table 4-1 Troubleshooting PROBLEM PROBABLE CAUSE REMEDY Uneven Till Tiller not level right to left Adjust skids for same depthAdjust tractor lower lift arms Noisy Loose components Check all bolts for tightness. Refer to Torque Specs Low oil in gearbox Check for proper oil level. Refer to Lubrication...

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, providesafety decals for any of our products in the field at no charge. Contact...

B O L T D I A M E T E R W R E N C H ( I N . ) “ B ” A N D S A E S A E S A E S I Z E ( I N . ) “ A ” T H R E A D S I Z E G R A D E 2 G R A D E 5 G R A D E 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (1...

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as ...