Page 3 - TABLE OF CONTENTS
TABLE OF CONTENTS SAFETY SECTION .............................................................................................................. 1-1 General Safety Instructions and Practices ......................................................................................................... 1-2O...
Page 5 - SAFETY SECTION
Page 6 - General Safety Instructions and Practices
SAFETY 1947/2047 01/11 Safety Section 1-2 © 2011 Alamo Group Inc. SAFETY General Safety Instructions and Practices A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be tothe owner/operator. Most accidents can be avoided by being aware of your equ...
Page 8 - Operator Safety Instructions and Practices
SAFETY 1947/2047 01/11 Safety Section 1-4 © 2011 Alamo Group Inc. SAFETY Operator Safety Instructions and Practices Never operate the Tractor or Implement until you have read andcompletely understand this Manual, the Tractor Operator’s Manual, andeach of the Safety Messages found in the Manual or on...
Page 9 - Equipment Operation Safety Instructions and Practices
SAFETY 1947/2047 01/11 Safety Section 1-5 © 2011 Alamo Group Inc. SAFETY Equipment Operation Safety Instructions and Practices Prolonged operation may cause operator boredom and fatigue affecting safe operation.Take scheduled work breaks to help prevent these potentially impaired operatingconditions...
Page 16 - Transporting Safety Instructions and Practices
SAFETY 1947/2047 01/11 Safety Section 1-12 © 2011 Alamo Group Inc. SAFETY Transporting Safety Instructions and Practices Transport only at speeds where you can maintain control of theequipment. Serious accidents and injuries can result from operating thisequipment at high speeds. Understand the Trac...
Page 17 - Maintenance and Service Safety Instructions and Practices
SAFETY 1947/2047 01/11 Safety Section 1-13 © 2011 Alamo Group Inc. SAFETY Maintenance and Service Safety Instructions and Practices Lower the loader to the bed of the truck or trailer when transporting thetractor and loader with a truck. Measure to ensure the transport heightdoes not exceed the lega...
Page 19 - Storage and Parking Safety Instructions and Practices
SAFETY 1947/2047 01/11 Safety Section 1-15 © 2011 Alamo Group Inc. SAFETY Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and Practices Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protectionwhen servicing hot components. Contact w...
Page 20 - Decal Location
SAFETY 1947/2047 01/11 Safety Section 1-16 © 2011 Alamo Group Inc. SAFETY Decal Location NOTE: Bush Hog supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in shipping, use, or reconditioning. Bush Hog cares about the safety of its customers, operat...
Page 22 - Decal Description
SAFETY 1947/2047 01/11 Safety Section 1-18 © 2011 Alamo Group Inc. SAFETY Decal Description P/N 50057411 Logo: BUSH HOG (3.20” x 14.50”) MODEL NAME: 1947 P/N 50069067 MODEL NAME: 2047 P/N 50069068
Page 27 - INTRODUCTION SECTION
Page 28 - INTRODUCTION
INTRODUCTION 1947/2047 01/11 Introduction Section 2-2 © 2011 Alamo Group Inc. INTRODUCTION This 1947/2047 Loader is designed with care and built with quality materials by skilled workers. Properassembly, maintenance, and operating practices, as described in this manual, will help the owner/operator ...
Page 31 - Attention Owner/Operator
INTRODUCTION 1947/2047 01/11 Introduction Section 2-5 © 2011 Alamo Group Inc. INTRODUCTION Attention Owner/Operator BEFORE OPERATING THIS MACHINE: 1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, andknow how to operate correctly both the tractor an...
Page 34 - Assembly Instructions
ASSEMBLY 1947/2047 01/11 Assembly Section 3-2 © 2011 Alamo Group Inc. ASSEMBL Y Assembly Instructions To avoid injury during installation of loader, do not allow bystanders within 10 feet of loaderor attachment. Always have a heavy attachment, such as a bucket mounted on loader when it is removedfro...
Page 35 - Proper Rear Ballasting and Wheel Spacing
ASSEMBLY 1947/2047 01/11 Assembly Section 3-3 © 2011 Alamo Group Inc. ASSEMBL Y Proper Rear Ballasting and Wheel Spacing Spread front wheels to maximum distance. Spread rear wheels to maximum distance. Add rear wheel weight, rear ballast box orimplement. Make sure there is 25% of total weighton rear...
Page 36 - Installing Mounting Brackets
ASSEMBLY 1947/2047 01/11 Assembly Section 3-4 © 2011 Alamo Group Inc. ASSEMBL Y Installing Mounting Brackets Install all mounting brackets on the tractor according to instructions packed with mounting kit. NOTE: Leave all hardware loose until the loader is completely assembled to facilitate assembly...
Page 38 - Installing Bucket Level Indicator; Dismounting Loader and Mounting Loader to Tractor; Dismounting Loader
ASSEMBLY 1947/2047 01/11 Assembly Section 3-6 © 2011 Alamo Group Inc. ASSEMBL Y Installing Bucket Level Indicator Slide bucket level indicator rod (16) into bracket(18) and attach the other end of rod to bucket with1/8” X 1” cotter pins (22).Locate tractor and loader on level surface. With thebottom...
Page 39 - Mounting Loader
ASSEMBLY 1947/2047 01/11 Assembly Section 3-7 © 2011 Alamo Group Inc. ASSEMBL Y 5. Start tractor engine and release tractor brakes. Activate lift control lever to raise side frames up off mid mounting assembly. Continue activating the loft control lever while gradually backing the tractor up.Allow l...
Page 41 - OPERATION SECTION
Page 42 - OPERATION; OPERA; OPERATION INSTRUCTIONS
OPERATION 1947/2047 01/11 Operation Section 4-2 © 2011 Alamo Group Inc. OPERA T ION Bush Hog 1947 & 2047 LOADER OPERATION INSTRUCTIONS Your 1947 & 2047 Loader should now be assembled and inspected for any evidence of defective or damagedparts before use. Any evidence of damage should be repo...
Page 43 - Standard Equipment and Specifications
OPERATION 1947/2047 01/11 Operation Section 4-3 © 2011 Alamo Group Inc. OPERA T ION 1. Standard Equipment and Specifications Specifications will vary with tire size, hydraulic system and bucket used. Specifications are given for a loaderequipped with a 48” bucket, external hydraulic system of 4.75 G...
Page 44 - Operator Requirements
OPERATION 1947/2047 01/11 Operation Section 4-4 © 2011 Alamo Group Inc. OPERA T ION 2. Operator Requirements DO NOT use drugs or alcohol immediately before or while operating theTractor and Implement. Drugs and alcohol will affect an operator’salertness and coordination and therefore affect the oper...
Page 47 - Tractor Requirements; Tractor Requirements and Capabilities; ROPS and Seat Belt
OPERATION 1947/2047 01/11 Operation Section 4-7 © 2011 Alamo Group Inc. OPERA T ION 3. Tractor Requirements Tractor Requirements and Capabilities • ASABE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt. • Tractor Safety Devices .................Slow Moving Vehicle (SMV) embl...
Page 48 - Tractor Lighting and SMV Emblem
OPERATION 1947/2047 01/11 Operation Section 4-8 © 2011 Alamo Group Inc. OPERA T ION 3.3 Tractor Ballast Before operating tractor and loader, add sufficient counterweight so a minimum of 25% of thetotal weight is on the rear axle. Total weight includes weight of: tractor, loader, rated load inbucket,...
Page 49 - Getting On and Off the Tractor; Boarding the Tractor
OPERATION 1947/2047 01/11 Operation Section 4-9 © 2011 Alamo Group Inc. OPERA T ION 4. Getting On and Off the Tractor 4.1 Boarding the Tractor Do not mount or dismount the Tractor while the tractor is moving. Mountthe Tractor only when the Tractor and all moving parts arecompletelystopped. (SG-12) B...
Page 50 - Dismounting the Tractor
OPERATION 1947/2047 01/11 Operation Section 4-10 © 2011 Alamo Group Inc. OPERA T ION 4.2 Dismounting the Tractor BEFORE leaving the tractor seat lower the implement, set the parkingbrake and/or set the tractor transmission in parking gear, disengage thePTO, stop the engine, remove the key, and wait ...
Page 51 - Starting the Tractor
OPERATION 1947/2047 01/11 Operation Section 4-11 © 2011 Alamo Group Inc. OPERA T ION 5. Starting the Tractor Never run the Tractor engine in a closed building or without adequate ventilation. Theexhaust fumes can be hazardous to your health. (SG-23) Start tractor only when properly seated in the Tra...
Page 56 - Tractor PRE-OPERATION Inspection; Item; DO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT
OPERATION 1947/2047 01/11 Operation Section 4-16 © 2011 Alamo Group Inc. OPERA T ION Tractor PRE-OPERATION Inspection Tractor ID#:________________________Make:________________________ Date:______________________________Shift:________________________ Before conducting the inspection, make sure the tr...
Page 57 - FRONT END LOADER PRE-OPERATION Inspection
OPERATION 1947/2047 01/11 Operation Section 4-17 © 2011 Alamo Group Inc. OPERA T ION Driving the Tractor and Loader FRONT END LOADER PRE-OPERATION Inspection Front End Loader ID#_______________Make____________________ Date_____________________________Shift____________________ Before conducting the i...
Page 59 - Driving the Tractor and Loader; Operating the Tractor and Loader
OPERATION 1947/2047 01/11 Operation Section 4-19 © 2011 Alamo Group Inc. OPERA T ION Safe tractor transport requires the operator possess a thorough knowledge of the model being operated andprecautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle th...
Page 64 - Operating the Loader; FILLING THE BUCKET
OPERATION 1947/2047 01/11 Operation Section 4-24 © 2011 Alamo Group Inc. OPERA T ION 7.1 Operating the Loader The following text and illustrations offer suggested loader and tractor operating techniques. FILLING THE BUCKET Approach and enter the pile with a level bucket. Loaders with 1-lever control...
Page 66 - LIFTING THE LOAD
OPERATION 1947/2047 01/11 Operation Section 4-26 © 2011 Alamo Group Inc. OPERA T ION A level bucket throughout the lifting cycle resists bucket lift and increases breakaway effort. NOTE: Do not be concerned if the bucket is not completely filled during each pass. Maximumproductivity is determined by...
Page 67 - CARRYING THE LOAD
OPERATION 1947/2047 01/11 Operation Section 4-27 © 2011 Alamo Group Inc. OPERA T ION CARRYING THE LOAD Position bucket just below tractor hood formaximum stability and visibility, whether bucket isloaded or empty. Use extreme care when operating loader on aslope, keep bucket as low as possible. This...
Page 68 - DUMPING THE BUCKET
OPERATION 1947/2047 01/11 Operation Section 4-28 © 2011 Alamo Group Inc. OPERA T ION DUMPING THE BUCKET Lift bucket high enough to clear side of vehicle.Move tractor in as close as possible to side ofvehicle, then dump bucket. LOWERING THE BUCKET After bucket is dumped, back away from vehiclewhile l...
Page 69 - OPERATING WITH FLOAT CONTROL
OPERATION 1947/2047 01/11 Operation Section 4-29 © 2011 Alamo Group Inc. OPERA T ION OPERATING WITH FLOAT CONTROL During hard surface operation, keep bucket leveland put lift control in float position to permit bucketto float on working surface. If hydraulic downpressure is exerted on bucket, it wil...
Page 70 - LOADING FROM A BANK
OPERATION 1947/2047 01/11 Operation Section 4-30 © 2011 Alamo Group Inc. OPERA T ION LOADING FROM A BANK Choose a forward gear that provides sufficientground speed for loading. Exercise caution when undercutting high banks.Dirt slides can be dangerous. Load from as low aspossible for maximum efficie...
Page 72 - PEELING AND SCRAPING
OPERATION 1947/2047 01/11 Operation Section 4-32 © 2011 Alamo Group Inc. OPERA T ION PEELING AND SCRAPING Use a slight bucket angle, travel forward and holdlift control forward to start the cut. Make a short 5 to8 foot angle cut and break out cleanly. With bucket level, start a cut at notch approxim...
Page 73 - LOADING LOW TRUCKS OR SPREADERS FROM A PILE
OPERATION 1947/2047 01/11 Operation Section 4-33 © 2011 Alamo Group Inc. OPERA T ION LOADING LOW TRUCKS OR SPREADERS FROM A PILE For faster loading, minimize angle of turn andlength of run between pile and spreader. Backgrade occasionally with a loaded bucket to keepworking surface free of ruts and ...
Page 74 - BACKFILLING
OPERATION 1947/2047 01/11 Operation Section 4-34 © 2011 Alamo Group Inc. OPERA T ION BACKFILLING Approach pile with a level bucket. Poor methods actually move no more dirt and makeit more difficult to hold a level grade. Do not use bucket in dumped position forbulldozing. This method, shown above, w...
Page 76 - HANDLING LARGE HEAVY OBJECTS
OPERATION 1947/2047 01/11 Operation Section 4-36 © 2011 Alamo Group Inc. OPERA T ION Leave dirt which drifts over side of bucket for final cleanup. Pile dirt on high side for easier backfilling on aslope. HANDLING LARGE HEAVY OBJECTS 1. Using front end loaders for handling large heavy objects such a...
Page 77 - Operating Bale Spear
OPERATION 1947/2047 01/11 Operation Section 4-37 © 2011 Alamo Group Inc. OPERA T ION 7.2 Operating Bale Spear Operate the bale spear using extreme caution. Sharp points on bale spear can causeserious injury or death. Because of size and weight of large bales, extreme care must be taken in handling t...
Page 78 - Shutting Down the Implement
OPERATION 1947/2047 01/11 Operation Section 4-38 © 2011 Alamo Group Inc. OPERA T ION Carry bales as low to the ground as possible toallow maximum visibility and avoid tipping. 8. Loader Storage Properly preparing and storing the loader at the end of the season is critical to maintaining its appearan...
Page 79 - Transporting the Tractor and Implement
OPERATION 1947/2047 01/11 Operation Section 4-39 © 2011 Alamo Group Inc. OPERA T ION 9. Transporting the Tractor and Implement Never allow children or other persons to ride on the Tractor or Implement.Falling off can result in serious injury or death. (SG-10) Transport only at speeds where you can m...
Page 82 - Hauling the Tractor and Implement
OPERATION 1947/2047 01/11 Operation Section 4-42 © 2011 Alamo Group Inc. OPERA T ION When operating on public roads, have consideration for other road users. Pull to the side of the roadoccasionally to allow all following traffic to pass. Do not exceed the legal speed limit set in your country forag...
Page 83 - Troubleshooting Guide
OPERATION 1947/2047 01/11 Operation Section 4-43 © 2011 Alamo Group Inc. OPERA T ION 10. Troubleshooting Guide TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Loader slow or will not lift Hydraulic oil too heavy. Change to proper oil. and/or dump Oil filter plugged. Clean or replace filter. Hydraulic pump wo...
Page 85 - MAINTENANCE SECTION
Maintenance Section 5-1 © 2011 Alamo Group Inc. MAINTENANCE SECTION
Page 86 - MAINTENANCE
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-2 © 2011 Alamo Group Inc. MAINTENANCE READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury ordeath may occur unless care is taken to follow the warnings and instructions stated in theSafety Messages. Always use good common sense...
Page 88 - Lubrication Schedule
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-4 © 2011 Alamo Group Inc. MAINTENANCE Lubrication Schedule Before operating your Loader, take the time to inspect and repair any damage to the machine or tractor. Only aminimum of time and effort is required to regularly maintain this machine to prov...
Page 89 - Daily Maintenance
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-5 © 2011 Alamo Group Inc. MAINTENANCE Daily Maintenance Regular maintenance of your loader and hydraulic system will insure maximum loader efficiency and long life. 1. Check fluid level of tractor hydraulic system before starting each day’s operation...
Page 90 - Hydraulic Pressure Check; Cylinder Service
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-6 © 2011 Alamo Group Inc. MAINTENANCE Hydraulic Pressure Check Following procedure outlines hydraulic pressure check. 1. Obtain a pressure gauge that measures 3000 PSI in 50 PSI increments. 2. Install gauge into the hydraulic line connecting the load...
Page 91 - Lift and Bucket Cylinder Dissemble; Lift and Bucket Cylinder Reassembly
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-7 © 2011 Alamo Group Inc. MAINTENANCE Lift and Bucket Cylinder Dissemble Following is an outline procedure for disassembling and reassembling cylinders 1. Hold cylinder tube (13) stationary and pull wire ring (14) out through slot. 2. Pull shaft (1),...
Page 92 - Prince LVR Valve Service
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-8 © 2011 Alamo Group Inc. MAINTENANCE Prince LVR Valve Service The valve has a valve relief setting pre-set at the factory. Tampering with this setting cancause serious injury to operator and damage to tractor or loader. Unauthorized adjustmentsor se...
Page 93 - Valve Disassembly
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-9 © 2011 Alamo Group Inc. MAINTENANCE Valve Disassembly Note: It is advisable to mark or tag all parts so they will be reinstalled in their proper position. 1. Slide boot (6) to top of handle (34). Remove hex head cap screws (36) from rod ends (9 &am...
Page 94 - Valve Reassembly; Relief Valve, Load Check Plugs and Power Beyond Sleeve; Replacing Handle Parts; Storage
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-10 © 2011 Alamo Group Inc. MAINTENANCE Valve Reassembly 1. Examine all parts for wear and damage and replace if necessary. 2. Lubricate all o-rings and spools with oil to prevent damage when assembling. 3. Lubricate all detent and spring centering pa...
Page 96 - Proper Torque for Fasteners
MAINTENANCE 1947/2047 01/11 Maintenance Section 5-12 © 2011 Alamo Group Inc. MAINTENANCE Proper Torque for Fasteners The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer tothis chart to determine the grade of bolts and the proper torque excep...
Page 100 - LIMITED WARRANTY; DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES; THIS LIMITED WARRANTY SHALL NOT APPLY:
LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized BushHog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year fornon-commercial, state and munic...
Page 102 - LOADER
1947/2047-SOM-01/11 P/N 50069199 Printed U.S.A 1947/2047 LOADER