Bunn G9WD-RH - Manual - manualsarea.com

Page 2 - SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

2 41451.0001 041410 BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Comp...

Page 3 - when adding beans. Use only with whole bean coffee.

3 USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written for your protection. All notices on the grinder are to be kept in good condition. Replace any unreadable or damaged labels. #20545.0000 CONTENTS Introduction .......................................

Page 4 - Pressing initiates a grind cycle.

4 ELECTRICAL REQUIREMENTS This grinder has an attached cord set and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. OPERATING CONTROLS Grind Pad (a) Pressing initiates a grind cycle. Stop Pad (b) Pressing ends the operation of the grinder. ® Pad (c) Pressing the co...

Page 5 - COFFEE GRINDING; Insert the funnel into the funnel rails until it stops.; ADJUSTMENTS; Burr Adjustment; Remove two black screws from the lower control panel bezel.

5 COFFEE GRINDING 1. Visually inspect the hopper for an ample supply of whole bean coffee. 2. Place a paper filter into the brew funnel. The filter must not be folded-over or tilted to one side. 3. Insert the funnel into the funnel rails until it stops. 4. Select batch size desired (e). 5. Momentari...

Page 6 - CLEANING

6 CLEANING WARNING – Unplug grinder before the removal of any panel or grind chamber-housing parts. 1. Clean all exterior surfaces using a damp cloth rinsed in any mild, nonabrasive, liquid detergent. Care should be taken not to scratch the grinder with any abrasive material. 2. Remove the hopper by...

Page 7 - GLOSSARY

7 GLOSSARY GRIND OZ: ##.## (-) DONE (+) Adjust current weight setting using (-) and (+) buttons Allows adjustment of current time setting Adjust current time setting us- ing (-) and (+) buttons Allows adjustment of other batch sizes (multiple batch size grinders only) Test individual inputs and out-...

Page 9 - COMMUNICATING WITH THE GRINDER

9 COMMUNICATING WITH THE GRINDER Press the hidden (copyright) button for 1 second Press right hidden (copyright) button to scroll to next screen Press right hidden (copyright) button to scroll to next screen Pressing “PREV” scrolls to the previous coffee name Pressing “NEXT” scrolls to the next coff...

Page 10 - COMMUNICATING WITH THE GRINDER (Continued)

10 COMMUNICATING WITH THE GRINDER (Continued) From previous page Loop back to “COFFEE NAME” Press “GRIND” button to start coffee calibration The small batch size will flash, press (-) or (+) to adjust grind weight. After first batch size is set, additional batch sizes can be set by pressing appropri...

Page 15 - SCHEMATIC WIRING DIAGRAM G9WD-RH

15 BLK WHT RED RED VIO BLK BLK VIO VIO K1 N.O. M K1 BLK WHT L1 N L1 L2 1 4 J1 CONTROL CIRCUIT BOARD LOAD TRANSDUCER BLK GRN WHT RED 1 4 J7 GRN SCHEMATIC WIRING DIAGRAM G9WD-RH 120 VOLTS AC 2 WIRE SINGLE PHASE 60 HZ BLK VIO T1 LINE LOAD WHT BLK RED RED 1 2 4 5 YEL YEL BLK WHT J13 1 5 10 16 BUTTON BUT...

Bunn G9WD-RH - Manual

Table of Contents:

Summary

Other Bunn Models