Bunn FMD-5 - Manual

Bunn FMD-5

Bunn FMD-5 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
Page: / 45

Table of Contents:

  • Page 4 – ELECTRICAL REQUIREMENTS; Refer to the dispenser’s dataplate for exact voltage requirement.); CAUTION; An electrician must provide electrical service as specified.; PLUMBING REQUIREMENTS; NOTE
  • Page 5 – LIQUID LEVEL CONTROL
  • Page 7 – DRAINING THE HOT WATER TANK; Be very careful with the draining water because it can be very hot.; The dispenser must be refilled using the
  • Page 8 – TROUBLESHOOTING; WARNING –
  • Page 13 – SERVICE
  • Page 14 – Wash components in a mild solution of dish deter-
  • Page 20 – CONTROL BOARD
  • Page 25 – FAN
  • Page 28 – INCREASE/DECREASE SWITCH
  • Page 29 – LAMP HOLDERS
  • Page 31 – LIMIT THERMOSTAT; FIG. 23 LIMIT THERMOSTAT; BLK to Tank Heater; Refer to Fig. 24 when reconnecting the wires.
  • Page 38 – TANK HEATER
  • Page 39 – TANK HEATER SWITCH
  • Page 41 – TRANSFORMER
Loading the manual

OPERATING & SERVICE MANUAL

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

www.bunnomatic.com

FMD-4

FMD-5

35135.0000 03/03 ©2003 Bunn-O-Matic Corporation

BUNN

®

PLACE

CUP

HERE

PLACE

CUP

HERE

PLACE

CUP

HERE

PLACE

CUP

HERE

PLACE

CUP

HERE

RELEASE BUTT

ON WHEN CUP

IS 2/3 FULL

!

W

ARNING

H O T

L I

Q

U I D

PUSH and HOLD BUTT

ON UNTIL

CUP

IS 2/3 FULL, THEN RELEAS

E

RINSE

RINSE

PLACE

CUP

HERE

PLACE

CUP

HERE

PLACE

CUP

HERE

PLACE

CUP

HERE

RELEASE BUTT

ON WHEN CUP

IS 2/3 FULL

!

W

ARNING

H O T

L I

Q U I D

PUSH and HOLD BUTT

ON UNTIL

CUP

IS 2/3 FULL, THEN RELEASE

RINSE

RINSE

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 4 - ELECTRICAL REQUIREMENTS; Refer to the dispenser’s dataplate for exact voltage requirement.); CAUTION; An electrician must provide electrical service as specified.; PLUMBING REQUIREMENTS; NOTE

4 INITIAL SET-UP 1. Locate the drip tray assembly inside the dispenser door. 2. Remove the drip tray and the drip tray cover and set them aside. ELECTRICAL REQUIREMENTS CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up. The 120 volt version of this ...

Page 5 - LIQUID LEVEL CONTROL

5 INITIAL FILL & HEAT CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Turn-on the water supply and connect the dispenser to the power source.2. Water will automatically flow into the tank to the prope...

Page 7 - DRAINING THE HOT WATER TANK; Be very careful with the draining water because it can be very hot.; The dispenser must be refilled using the

7 DRAINING THE HOT WATER TANK CAUTION - The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source.2. Place the tank heater switch in the “OFF” position.3. Shut-off and disconnect the incoming water supply.4. Remove the front, l...

Other Bunn Models

All Bunn Other