Bunn FMD-4 - Manual

Bunn FMD-4

Bunn FMD-4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69
70 Page 70
71 Page 71
Page: / 71

Table of Contents:

  • Page 3 – USER NOTICES; Replace any unreadable or damaged labels.; CONTENTS; Preventive Maintenance; SITE PREPARATION; space so the dispenser can be moved for cleaning.; INTRODUCTION; Basic Maintenance
  • Page 4 – CLEANING; NOTICE
  • Page 5 – REQUIRED REGULAR MAINTENANCE:
  • Page 6 – TROUBLESHOOTING; PROBLEM
  • Page 11 – NOTES
  • Page 12 – SERVICE; Refer to the contents listing for component location.; INDEX
  • Page 13 – all screws and other attaching hardware for re-assembly.
  • Page 15 – AUGER DRIVE COMPONENTS
  • Page 20 – NOTE: Verify the ground wire is connected to the board
  • Page 25 – NOTE: J4 is not connected on Control Board #2 on
  • Page 26 – NOTE - The capillary tube must be clear of any electrical
  • Page 29 – Note: Pin 1 of the connector is identified by an arrow
  • Page 31 – Across either pair
  • Page 32 – Diagrams and check the dispenser wiring harness.
  • Page 33 – Diagrams and check the dispenser wiring harness
  • Page 34 – NOTE: To remove the recptacle only, rotate clockwise; BLK to Main Harness
  • Page 44 – NOTE - The magnets must be at the top of float and
  • Page 46 – SOLENOID VALVE (COLD WATER - OPTIONAL for
  • Page 47 – Diagrams and check dispenser wiring harness.
  • Page 50 – NOTE - If the tank heater remains unable to heat, remove; FIG. 51 TANK HEATER TERMINALS; Resistance Values
  • Page 54 – TRIAC MAPS for FMD
  • Page 55 – SINGLE PHASE; SCHEMATIC WIRING DIAGRAM FMD-1
  • Page 56 – SCHEMATIC WIRING DIAGRAM FMD-1A
  • Page 57 – SCHEMATIC WIRING DIAGRAM FMD-2
  • Page 60 – SCHEMATIC WIRING DIAGRAM FMD-2FD
  • Page 65 – SCHEMATIC WIRING DIAGRAM FMD DBC-3
  • Page 66 – SCHEMATIC WIRING DIAGRAM FMDA DBC-3
Loading the manual

SERVICE & REPAIR MANUAL

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

42672.0000B 06/12 ©2009 Bunn-O-Matic Corporation

FMD Series

Including: FMD-1,2,3,4,5

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - USER NOTICES; Replace any unreadable or damaged labels.; CONTENTS; Preventive Maintenance; SITE PREPARATION; space so the dispenser can be moved for cleaning.; INTRODUCTION; Basic Maintenance

3 USER NOTICES All notices on this equipment are written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels. CONTENTS Warranty .......................................................................................................................

Page 4 - CLEANING; NOTICE

4 CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur- faces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 1 x 24h 37254.0000A 07/04 © 2004 BUNN-O-MATIC CORPORATION NOTICE The cleaning instructions ...

Page 5 - REQUIRED REGULAR MAINTENANCE:

5 REQUIRED REGULAR MAINTENANCE: When performing Daily-Weekly Cleaning procedures, inspect o-rings, seals, and bushings for signs of wear or damage and replace immediately. Check and/or replace every 6 months or as required: 32906.0000 Mixing Chamber Kit (Includes items indented below) 25732.0000 Ste...

Other Bunn Models

All Bunn Other