Page 2 - WARRANTY; workmanship for two years from the date of installation.; CONTENTS
2 WARRANTY Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects in material and workmanship existing at the time of manufacture and appearing within one year from the date ofinstallation. In addition: 1.) Bunn warrants electronic circuit and/or c...
Page 3 - USER NOTICES; WARNING; CHARGE
3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 00986.0002 33461.0000 ! WARNING DO NOT OVERLOAD CIRCUIT.ALWAYS ELECTRI...
Page 4 - do not; ELECTRICAL REQUIREMENTS
4 INITIAL SET-UP CAUTION: The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser. Place the dispenser on a sturdy counter or shelf able to support at least 250 lbs. (113.4kg). The FCD-4 is designed for indoor use only. 1. Set the dispen...
Page 5 - PLUMBING REQUIREMENTS; COLD WATER
5 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WATER system with operating pressure between 20 and 100 psi (138 and 690 kPa). This water source must be capable of producing a minimum flow rate of 3 fluid ounces(88.7 milliliters) per second. A shut off valve should be installed in...
Page 6 - OPERATING CONTROLS; Refrigeration Switch; FIG 3 Refrigeration Switch
6 OPERATING CONTROLS Refrigeration Switch The refrigeration switch is located on the top of the dispenser nearthe left rear corner. This switch controls power to the compressorand the condenser fan motor. Sanitize Switch The sanitize switch is located behind the drip tray in thelower left corner of ...
Page 8 - INITIAL FILL; specified in the instructions.
8 INITIAL FILL CAUTION: The dispenser must be disconnected from the power source throughout the initial fill except when specified in the instructions. 1. Remove drip tray assembly and splash panel from the dispenser.2. Pull the overflow tube from its retaining clip and place the end into an empty 6...
Page 9 - PRIMING; The dispenser will not operate with the door open.
9 INITIAL FILL (cont) Ambient Concentrates (Optional) 1. Install an Ambient Concentrate Conversion Kit (BUNN-O-MATIC part number 33699.0000) per the instructions provided in the kit. 2. Attach the concentrate product hose to the appropriate concentrate line located behind the dispenser’s splash pane...
Page 10 - DISPENSER USE; Press and Hold Models; to produce the approximate beverage sizes as follows:
10 DISPENSER USE Press and Hold Models (Refer to Fig 5) 1. Place a cup on the drip tray beneath the desired dispensing nozzle.2. Press and hold the “Product Dispense” or “Chilled Water” switch until the beverage/water reaches the desired level, then release. Portion Control Models (Refer to Fig 6) 1...
Page 11 - CLEANING & PREVENTIVE MAINTENANCE; General Cleaning and Sanitizing Procedures; IN THIS STEP SHOULD BE HANDLED WITH EXTREME CARE.)
11 CLEANING & PREVENTIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The Bunn Juice Dispenser incorporates a rinse reminder feature which lights the rinse led on the front panel when it is time to rinse. See dip switch function list to activate this feature. Daily: Rinse Procedu...
Page 13 - disconnect the wiring connections from the cabinet receptacles.
13 Monthly: Clean Condenser Air Filter 1. Remove the condenser air filter located on the rear of the dispenser.2. Using a water spray, clean the air filter. Annually: Replace Pump Tubing 1. Open dispenser door.2. Remove all product containers and place them in a refrigerated (35-40 degrees F [1.6-4....
Page 14 - ADJUSTMENT & OPTIONAL SETTINGS; Temperature Compensated Refractometer Method
14 ADJUSTMENT & OPTIONAL SETTINGS SETTING THE MIX RATIO/BRIXRatio Cup Method 1. Adjust the water flow as described in Water Flow Testing and Adjustment. 2. Remove the dispense nozzle from the appropriate dispense position.3. Assemble, lubricate, and install the Flow Separator Assembly (BUNN-O-MA...
Page 17 - beeper sounds twice and that the “PROGRAM” indicator extinguishes.; Service Lockout
17 b) In a 5 second period, press and release the “Chilled Water Switch” the number of times that you want thepassword set to (maximum of 10.) For example: If you want the password set to 3, press and release the“Chilled Water Switch” 3 times in the 5 second period.c) Release the “Hidden Switch”.d) ...
Page 18 - Password Protection
18 Password Protection The programming modes and service lockout function may be password protected to prevent accidental orunauthorized access to these features. The dispenser is shipped from the factory with a password of “0” (nopassword.) 1. Enter the “Pump Speed Programming” mode by simultaneous...
Page 20 - COOLANT SCHEMATIC DIAGRAM
20 COOLANT SCHEMATIC DIAGRAM CONDENSER SUCTION A CCUMULA T O R COMPRESSOR EV APORA T O R PR OCESS TUBE 33464.0000A 09/00 ©2000 Bunn-O-Matic Cor por ation FIL TER DR YER 33496 011101
Page 21 - SCHEMATIC WIRING DIAGRAM
21 J3-1 J3-2 J1-1 J1-5 J1-10 CONTROL P C BOARD J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 RIGHT LAMP ASSY. LEFT LAMP ASSY. GRN GRN GRN N L1 BLU BRN/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOSTAT K COMP. K COMPRESSOR ASSEMBLY + – RECT TRANSFORMER WHI/BLU WHI WHI WHI WHI/RED WHI/RED BLK B...