Page 2 - WARRANTY REGISTRATION AND POLICY; Any labor subject to warranty; must; be authorized by Buhler Manufacturing. The labor
PRINTED IN CANADA WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications....
Page 3 - Hydraulic Farm Loader; Operator’s Manual; Table of Contents; PLEASE READ AND UNDERSTAND THIS MANUAL
595 Hydraulic Farm Loader Operator’s Manual Table of Contents Section Introduction and Identification Safety and Pre-use Information Operating Information Assembly and Parts Information Description Page Warranty Registration and Policy............................................ Table of Contents .....
Page 5 - Pre-delivery Check List
3 Pre-delivery Check List Before delivering this equipment please complete the following check list. 1. The loader has been installed using the appropriate mounting kit for the tractor and loader. 2. The hydraulic system installed is appropriate for the tractor and loader 3. The loader is properly i...
Page 6 - Loader Identification Diagram
4 Loader Identification Diagram (HSL Model Shown) For further details refer to Loader Mainframe and Subframe diagrams.
Page 7 - Hydraulic (Hose Kit) Identification Diagrams
5 Hydraulic (Hose Kit) Identification Diagrams Hose Kit “A” Loader Powered by the tractor remotes. Consists of four hoses leading from loader tubing to tractor remote couplers Hose Kit “C” Loader operated by an external valve that is plumbed into the tractor hydraulic system. Consists of 4 hoses lea...
Page 8 - Safety
6 Safety • Never work beneath raised loader unless it is securely supported. The following are instructions for the Lift Lock Supports; -DO NOT USE WHEN TRACTOR IS MOVING.-DO NOT STORE LIFT LOCK SUPPORTS OTHER THAN WHERE INDICATED.-REPLACE IMMEDIATELY IF DAMAGED. -THE BUCKET MUST BE EMPTY-ALWAYS USE...
Page 9 - Important Precautions
7 Important Precautions ROLL-OVER HAZARD To prevent serious injury or death: Move and turn tractor at low speed. Carry load no higher than necessary to clear the ground when transporting.Add wheel ballast or rear weight for stability. Move wheels to widest possible settings to increase stability. It...
Page 10 - Safety Decals; CAUTION; OVERHEAD HAZARD; STAY AWAY FROM UNDER LIFT; WARNING
8 Safety Decals These decals are located as shown on the Decal Location diagram and the Sub-Frame Assembly diagram. 1. Read Operator's Manual before operating. 2. Move and turn tractor at low speed.3. Carry loader arms at a low position during transport.4. Lower loader arms, stop engine and lock bra...
Page 12 - General Instructions and Information
10 General Instructions and Information As with any piece of equipment, the care with which your loader is operated and maintained will greatly affect it’s life and the safety of the people using it. 1. Keep all pivots well lubricated for longer bushing life. Inspect every 500 hours of operation for...
Page 13 - Operation and Maintenance; GENERAL
11 Operation and Maintenance GENERAL Refer to tractor Operator’s Manual for Operating information on the tractor’s hydraulic system. Hydraulic systems using auxiliary valves should have them located for easy reach from the tractor seat. Hoses should be connected in such a manner that pushing forward...
Page 14 - Operating Suggestions for Loading
12 Operating Suggestions for Loading When handling heavy loads, be sure to lower lift arms slowly. This is known as feathering the hydraulic lever. If load is lowered too fast and stopped suddenly, excessive shock loads are created which can damage loader or tractor. When loading bucket, drive strai...
Page 16 - Attaching the Loader to Your Tractor
14 Attaching the Loader to Your Tractor 1. Position the tractor as centrally as possible and drive, using lowest gear possible, into the loader frame until hoses can be connected. 2. Couple up the hydraulic hose lines to the loader or tractor valve ensuring proper function (see Operator and Maintena...
Page 18 - Removing the Loader from Your Tractor
16 Removing the Loader from Your Tractor WARNING! When removing the loader, it must be fitted with a bucket or other suitable attachment to give the frame stability after removal. If this is not done, the frame will not remain standing. IMPORTANT! Always remove the loader on firm, level ground (away...
Page 20 - Trouble Shooting
PROBLEM POSSlBLE CAUSE REMEDY Loader slow and/or will not dump. Quick couplers leaking. Check connections and compatibility orreplace. Hydraulic oil too heavy. Change or replace filter. Oil filter plugged. Clean or replace filter. Hydraulic pump worn. Repair or replace pump. Oil line restricted or l...
Page 21 - General Notes and Instructions to the Operator; Regarding ALLIED TSL Loader Operations; true self levelling system; If the loader is raised with the; oil from the bucket piston side will be bypassed at; If the loader is lowered with the bucket; oil from the bucket shaft side will be bypassed at high
19 General Notes and Instructions to the Operator Regarding ALLIED TSL Loader Operations 1. The true self levelling system (TSL) utilizes mechanical linkages to maintain bucket level while raising and lowering. The pivot plate weldment, levelling tubes and linkages have been developed to ensure that...
Page 23 - Sub Frame Parts Table
Item Part No. Description Regular Quantity TSL Quantity S595 Quantity S595 TSL Quantity 1 25440 595 Sub Frame Weldment Left 1 - 2 25441 595 Sub Frame Weldment Right 1 - - - 1 25457 595 S Sub Frame Weldment Right - - 1 - 2 25458 595 S Sub Frame Weldment Left - - 1 - 3 110959 Hook Weldment 2 2 2 2 4 1...
Page 25 - Main Frame Parts Table
Item Part No. Description 595 595 S 1 25442 595 Main Frame Weldment 1 - 1 25443 595 S Main Frame Weldment - 1 2 24296 Quick Attach Weldment Left 1 1 3 24297 Quick Attach Weldment Right 1 1 4 112798 Tube Cross Qtach 2 1 5 108827 Pin Weldment 2 2 6 111231 Stand Weldment 2 2 7 113114 Strap Stand 2 2 8 ...
Page 28 - Hydraulic Plumbing Diagram
Page 29 - Plumbing Parts Table
Item Part No. Description Qty. 1 24458 2.5 Dia. X 20.63 Cyl. Assy. Bucket 2 2 24454 2.5 Dia. X 28.50 Cyl. Assy. Lift 2 3 812973 3/8 x 12" Hose 3/4 MORB x 3/4 SWFJIC 2 4 811754 3/8 x 18" Hose 3/4 MORB x 3/4 SWFJIC 2 5 812703 3/8 x 22" Hose 3/4 MORB x 3/4 SWFJIC 2 6 812947 3/8 x 22" Ho...
Page 32 - Hydraulic Cylinder Assembly; CAUTION: Maximum pressure – 2750 psi
30 595, S595, 595TSL, S595TSL Hydraulic Cylinder Assembly Bucket Cylinders Bucket Cylinders TSL Bucket Cylinders Lift Cylinders Lift Cylinders Diameter 2.50" 3.00" 3.00” 2.50" 3.00" Length of Stroke 20.63" 20.63" 22.00” 28.50" 28.50" Retracted Length 33.00" 33.00&...
Page 34 - Buhler Manufacturing; a partnership”
Buhler Manufacturing “ a partnership” 1260 Clarence Ave Winnipeg, MB. R3T 1T2 Ph.: (204) 661-8711 Fax: (204) 654-2503 www.buhler.com Printed in USA Allied Division 1260 Clarence Ave Winnipeg, MB. R3T 1T2 Ph.: (204) 661-8711 Fax: (204) 654-2503 Farm King Division 301 Mountain Street S. Morden, MB R6M...
