Broan BHFLED110 - User Manual

Page 1

MODELS BHFLED110 • BHF110

VENTILATION FAN
WITH HEATER & LIGHT

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE INSTALLING OR
USING THIS HEATER.

To reduce the risk of fire, electric shock, or injury to persons, observe the

following:

1. Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer at the address or telephone number
listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and

lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.

3. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.

4. When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

5. This heater is hot when in use. To avoid burns, do not let bare skin touch

hot surfaces. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothing, curtains, etc. at least 3 feet (0.9 m) from the
front of the heater.

6. Extreme caution is necessary when any heater is used by or near children

or invalids and whenever the heater is left operating and unattended.

7. Do not operate any heater after it malfunctions. Disconnect power at

service panel and have heater inspected by a reputable electrician before
reusing.

8. Do not use outdoors.
9. To disconnect heater, turn controls to off, and turn off power to heater

circuit at main disconnect panel (or operate internal disconnect switch, if
provided).

10. Do not insert or allow foreign objects to enter any ventilation or exhaust

opening, as this may cause an electric shock or fire, or damage the
heater.

11. To prevent a possible fire, do not block air intakes or exhaust in any

manner.

12. A heater has hot and arcing or sparking parts inside. Do not use it in

areas where gasoline, paint, or flammable vapors or liquids are used or
stored.

13. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or
injury to persons.

14. This product must be grounded.
15. Do not install heater in a tub or shower enclosure.
16. THIS PRODUCT MUST BE MOUNTED IN A FLAT CEILING ONLY.

Installations in ceilings 9-feet high or less will provide maximum comfort.
DO NOT MOUNT THIS PRODUCT IN A WALL.

17. Install heater in ceiling only - at least 6 inches from any wall.
18. Do not connect heater to dimmer switch or speed control.
19. Provide a separate 20 AMP circuit. Use 12 GA. power cable of type which

meets code. Use supply wiring rated for at least 90

O

C.

20. For greatest efficiency, install heater so heat is directed toward tub or

shower area. Avoid directing toward walls or windows.

SAVE THESE INSTRUCTIONS

PLAN THE INSTALLATION

The unit will operate most quietly and efficiently when located
where the shortest possible duct run and minimum number of
elbows will be needed.

Use a roof cap or wall cap that has a built-in damper to reduce
backdrafts.

Plan to supply the unit with proper line voltage and appropriate
power cable.

ROOF

CAP

*

4-IN. ROUND

ELBOW(S)

*

4-IN.

ROUND

DUCT

*

WALL

CAP

*

*

Purchase

separately

INSULATION

(Can be placed

around and over

housing.)

HOUSING

TYPICAL INSTALLATION

HOUSING

CEILING

JOIST, TRUSS,

OR I-JOISTS

MOUNTING

CHANNELS

GRILLE

CEILING

MATERIAL

POWER

CABLES

Housing mounted to joists, trusses, or I-joists.

Up to 24-inches on-center.

For Warranty Statement, Service

Parts, Technical Support, or to

Register your product, please visit

our website or call:

broan-nutone.com 800-558-1711.