Page 3 - able of Contents
1 SAFETY NOTICE ................................................................. 2-3 LIST OF MATERIALS ....................................................... 4 INSTALLATION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance ............................
Page 4 - Important Safety Notice; READ AND SAVE THESE INSTRUCTIONS
Important Safety Notice READ AND SAVE THESE INSTRUCTIONS 2 www.zephyronline.com WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this u...
Page 6 - List of Materials
List of Materials 4 www.zephyronline.com (3) Wire Nuts (1) Suction Cup (4) ø12 OD / ø5 ID Washers (4) M4 x 1-1/2” Wood Screws (2) M4 x 8 Philips Head Screws 1 - Hardware package 1 - Top support frame 1 - Bottom support frame 1 - Top duct cover 1 - Bottom duct cover 1 - Hood body 3 - Metal mesh filte...
Page 7 - Installation –
5 Duct pieces Total Equivalent numberlength x used = 3- 1/ 4” x 10”Rect.,straight 1 Ft. x ( ) = Ft. 8” Round,straight 1 Ft. x ( ) = Ft. 3- 1/ 4” x 10”Rect. 90 0 elbow 15 Ft. x ( ) = Ft. 3- 1/ 4” x 10”Rect. 45 0 elbow 9 Ft. x ( ) = Ft. 3- 1/ 4” x 10”Rect. 90 0 flat elbow 24 Ft. x ( ) = Ft. 3- 1/ 4” x...
Page 8 - DUCTING
Installation – Mounting Height & Clearance 6 www.zephyronline.com DUCTING A minimum of 6” round ducting must be used to maintain maximum air fl ow effi ciency. Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%. Use calculation worksheet to compute total...
Page 9 - WARNING FIRE HAZARD
7 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal scr...
Page 12 - Mount hood onto support frame
10 www.zephyronline.com Mount hood onto support frame 6. Lift lower duct cover and hood body onto bottom of support frame. 7. Secure hood body to bottom support with (4) screws. Access the screwsfrom inside the hood. This will require at least two people. Installation – Mounting the Hood WARNING: El...
Page 13 - RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED); Charcoal Filter Replacements
11 Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and fi ltered by a set of optional charcoal fi lters. Th...
Page 14 - will; Features & Controls –
12 www.zephyronline.com Lights On/Dim/Off 15 Min Delay Off Display (speed level, delay off, filter clean/change) Adjust 6 Speed Levels Blower On/Off 1. Blower On/Off By pressing the blower is switched on and off. When switched on, the blower starts up on speed level 3. 2. Speed Selection The 6 speed...
Page 15 - Charcoal Filter Change Reminder (charcoal filter, if installed); Set Mode
Features & Controls – Charcoal Filter Change Reminder 13 Charcoal Filter Change Reminder (charcoal filter, if installed) When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust and fumes from cooking, then re-circulates the air within th...
Page 16 - Metal Filter Clean Reminder (metal mesh filter); Clean Filters
Features & Controls – Metal Mesh Filter Clean Reminder 14 www.zephyronline.com Metal Filter Clean Reminder (metal mesh filter) Whether your hood is installed as an exhaust or purifying unit, a set if metal mesh filters are fitted by the factory, These metal mesh filters are intended to filter ou...
Page 17 - Maintenance –
15 SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive st...
Page 18 - REPLACING LIGHT BULBS
16 www.zephyronline.com REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. No...
Page 19 - roubleshooting; TROUBLESHOOTING PROCEDURES FOR NAPOLI ISLAND
T roubleshooting 17 TROUBLESHOOTING PROCEDURES FOR NAPOLI ISLAND Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting pr...
Page 20 - DESCRIPTION; List of Parts and
18 www.zephyronline.com DESCRIPTION PART# Replacement Parts Light Bulb GU10 50W (each) Z0B-0020 Metal Filter (each) 50200004 Optional Accessories Recirculating Kit ZRC-0060 Replacement Charcoal Filter (each) Z0F-C002 Duct Cover Extension Z1C-00NA To order parts, visit us online at http://store.zephy...
Page 21 - STAPLE YOUR RECEIPT HERE; Two Year Limited Warranty for Parts:; associated with this warranty.; Warranty Exclusions:; with this warranty.; THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.; Some states or provinces do not; To Obtain Service Under Limited Warranty:; Limited Warranty; Proof of the original purchase
1-888-880-8368 STAPLE YOUR RECEIPT HERE TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) ...