Zenoah G6200 - Manuals - manualsarea.com

Page 2 - EXPLANATION OF SYMBOLS AND SAFETY WARNINGS; RISK OF DAMAGING HEARING

G6200 GB-2 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instructionbook before operating thismachine. Wear head, eye and earprotection. Use the chain sawwith two hands. Warning! Danger ofkickback. Read, understand andfollow all warnings. APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATIO...

Page 3 - Contents

G6200 G B GB-3 Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ......................................... 7 4. Fuel and Chain Oil .....

Page 4 - For safe operation

G6200 GB-4 10. Keep all parts of your body away from the saw chain when the engine is run-ning. 11. Before you star t the engine, make sure the saw chain is not contactinganything. 12. Always carry the chain saw with the engine stopped, the guide bar andsaw chain to the rear, and the muffleraway fro...

Page 6 - Explanation of Symbols on the Machine; WARNING

G6200 GB-6 2. Explanation of Symbols on the Machine WARNING • For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. The screw under the “H” stamp is The High-speed adjustment screw. The port to refu...

Page 7 - NOTE; Installing Guide Bar and Saw Chain

G6200 G B GB-7 5. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 6. While holding up the tip of the bar, adjust the chain tension by turning the tensioner screw until the tiestraps just touch the bottom side of the bar rail. 7. Tighten the nuts securely with the bar t...

Page 8 - Fuel and Chain Oil

G6200 GB-8 4. Fuel and Chain Oil ■ FUEL WARNING • Gasoline is very flammable . Avoid smoking or bringing any flame or sparks near fuel. Make sureto stop the engine and allow it cool before refuel-ing the unit. Select outdoor bare ground for fuel-ing and move at least 3 m (10 ft) away from thefueling...

Page 9 - Operating the Engine

G6200 G B GB-9 7. Allow the engine to warm up with the throttle lever pulled slightly. WARNING • Keep clear of the saw chain as it will start rotating upon starting of engine. ■ CHECKING THE OIL SUPPLY WARNING • Make sure to set up the bar and the chain when checking the oil supply.If not, the rotat...

Page 13 - Front and Rear dampers

G6200 G B GB-13 ■ PERIODICAL SERVICE POINTS 1. Cylinder fins Dust clogging between the cylinder fins will cause overheat-ing of the engine. Periodically check and clean the cylinderfins after removing the air cleaner and the cylinder cover. Wheninstalling the cylinder cover, make sure that switch wi...

Page 14 - Maintenance of Saw Chain and Guide Bar

G6200 GB-14 WARNING • This saw is equipped with one of the following low kickback bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain 16 3670-52112 848CC3LG60 (73LGX) 18 3673-52113 848CC3LG66 (73LGX) 20 3674-52113 848CC3LG72 (73LGX) WARNING • Be sure to round off the front edge t...

Page 15 - Troubleshooting Guide; Case 1. Starting failure; Rough idling

G6200 G B GB-15 9. Troubleshooting Guide Case 1. Starting failure WARNING • Make sure the icing prevention system is not working. 11. Specifications Power unit: Displacement (cm 3 ): ............................................. 62.0 Fuel: ................ Mixture (Gasoline 50 : Two-cycle oil 1)(whe...

Page 16 - Limited warranty; T H E WA R R A N T Y D O E S N OT A P P LY TO; THIS WARRANTY DOES NOT COVER; THERE ARE NO OTHER EXPRESS WARRANTIES.; ARE LIMITED

G6200 GB-16 Limited warranty Should any failure occur on the product under normaloperating conditions within the applicable warranty pe-riod, the failed part will be replaced or repaired free ofcharge by a ZENOAH authorized dealer. WARRANTY PERIOD: 1 year (6 months if used profes- sionally, and 30 d...