Zenoah G3300 - Manuals - manualsarea.com

Page 2 - EXPLANATION OF SYMBOLS AND SAFETY WARNINGS; RISK OF DAMAGING HEARING; MODEL

G3300 / G3300EZ GB-2 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instructionbook before operating thismachine. Wear head, eye and earprotection. Use the chain sawwith two hands. Warning! Danger ofkickback. Read, understand andfollow all warnings. WARNING!!! RISK OF DAMAGING HEARING IN...

Page 3 - Contents

G3300 / G3300EZ GB-3 G B Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ......................................... 6 4. Fuel and Ch...

Page 4 - For safe operation

G3300 / G3300EZ GB-4 1. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, orunder the influence of medica-tion that may make you drowsy,or if you are under the influenceof alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing andhead pro...

Page 5 - WARNING

G3300 / G3300EZ GB-5 G B move the clutch, structural dam-age to the flywheel could occurwhich could subsequently causethe flywheel to disintegrate.) 16. Always shut off the engine be- fore setting it down. 17. Use extreme caution when cut- ting small size brush and sap-lings because slender material...

Page 6 - A standard saw unit package contains the items as illustrated.

G3300 / G3300EZ GB-6 [G3300] 1. Pull the guard towards the front handle to check that the chain brake is not engaged. 2. Loosen the nut and remove the chain cover.3. Gear the chain to the sprocket and, while fitting the saw chain around the guide bar, mount the guidebar to the power unit. Adjust the...

Page 8 - HOW TO MIX FUEL; Fuel and Chain Oil; FUEL

G3300 / G3300EZ GB-8 ■ RECOMMENDED MIXING RATIOGASOLINE 50 : OIL 1 • Exhaust emission are controlled by the funda-mental engine parameters and components (eq.,carburation, ignition timing and port timing) with-out addition of any major hardware or the intro-duction of an inert material during combus...

Page 9 - Operating the Engine

G3300 / G3300EZ GB-9 G B Do not start the engine while the chain sawhangs in one hand. The saw chain may touchyour body. This is very dangerous. 6. When engine has ignited, pull the throttle slightly to return the choke knob to the original position. If theengine stops, pull the starter again withou...

Page 10 - Note: Be sure to adjust the carburetor with the bar chain attached.; STOPPING THE ENGINE

G3300 / G3300EZ GB-10 The carburetor on your unit has been factory adjusted,but may require fine tuning due to a change in operat-ing conditions.Before adjusting the carburetor, make sure that the pro-vided air/fuel filters are clean and fresh and the fuel prop-erly mixed. When adjusting, take the f...

Page 12 - Be alert to the springing back of a cut limb.; Pruning of Standing Tree; Cut up from the bottom, finish down from the top.

G3300 / G3300EZ GB-12 Before cleaning, the inspecting or repairingthe unit, make sure that engine has stoppedand is cool. Disconnect the spark plug to pre-vent accidental starting. ■ MAINTENANCE AFTER EACH USE 1. Oiling port Dismount the guide bar and check the oiling port forclogging. 7. Maintenanc...

Page 13 - PERIODICAL SERVICE POINTS; Loosen the knob by moving it to the direction A until

G3300 / G3300EZ GB-13 G B 2. Fuel filter Using a wire hook, take out the filter from the filler port.Clean away the dirt attached to the filter. Replace with anew one if needed. Note: Never bend the filter pipe when returning it. 3. Spark plug Clean the electrodes with a wire brush and reset thegap ...

Page 14 - Guide Bar; Maintenance of Saw Chain and Guide Bar; Saw Chain

G3300 / G3300EZ GB-14 side of a cutter. If a gap is observed between them,the rail is normal. Otherwise, the bar rail is worn.Such a bar needs to be corrected or replaced. WARNING: This saw is equipped with one of the following lowkickback bar/chain combinations: Komatsu Zenoah Part Number Saw Model...

Page 15 - Troubleshooting Guide; Case 1. Starting failure; Check spark ignition.; Rough idling

G3300 / G3300EZ GB-15 G B 9. Troubleshooting Guide Case 1. Starting failure Make sure the icing prevention system is notworking. Check fuel for wateror substandard mix-ture. Replace with properfuel. C h e c k f o r e n g i n eflooding. Check spark ignition. Remove and dry thespark plug.Then pull the...

Page 16 - Limited warranty; THE WARRANTY DOES NOT APPLY TO; THOSE UNITS; THIS WARRANTY DOES NOT COVER; THOSE PARTS; THERE ARE NO OTHER EXPRESS WARRANTIES.; INCLUDING THOSE OF MER-; ARE LIMITED; Specifications are subject to change wihout notice.

G3300 / G3300EZ GB-16 Limited warranty Should any failure occur on the product under normaloperating conditions within the applicable warranty pe-riod, the failed part will be replaced or repaired free ofcharge by a KOMATSU ZENOAH authorized dealer. WARRANTY PERIOD: 1 year (6 months if used profes- ...