Zenoah EXZ2610DL - Manuals

GB-6 EXZ2610DL 4. Symbols on the machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications,please be careful not to make a mistake. The port to refuel the “MIX GASOLINE” Position: FUEL TANK CAP The direction to close the choke Position: A...

GB-7 G B EXZ2610DL 1. Read this manual carefully until you completely understand andfollow all safety and operatinginstructions. 2. Keep this manual handy so that you may refer to it later when-ever any questions arise. Alsonote, if you have any questionsw h i c h c a n n o t b e a n s w e re dherei...

GB-11 G B EXZ2610DL Insert the cableto the end ofadjuster Full on stopper Idling adjust screw M3 screw Adjuster MOUNTING ENGINE 1. Push the shaft tube toward the clutch housing and rotate it by hand to check that the drive shaft is en-gaged with the gears. 2. Insert the shaft tube into the clutch ho...

GB-14 EXZ2610DL 6. Set up (HE-EX only) 4. Adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of thebar rail. (1) Chain tension adjusting screw (a) Loosen (b) Tighten 5. Tighten the mounting nut securely with the bar tip held up (TORQUE: 8.9 ~ 11.7...

GB-15 G B EXZ2610DL 7. Fuel and chain oil ■ FUEL WARNING • Gasoline is very flammable . Avoid smoking or bringing any flame or sparks near fuel. Make sureto stop the engine and allow it cool before refuel-ing the unit. Select outdoor bare ground for fuelingand move at least 3 m (10 ft) away from the...

GB-18 EXZ2610DL 8. Operation ADJUSTING THROTTLE CABLE • The normal play is 1 or 2 mm when measured at the carburetor side end. Readjust with the cable adjusteras required. (1) (1) Cable adjuster ADJUSTING IDLING SPEED (1) (1) Idle adjusting screw 1. When the engine tends to stop frequently at idling...

GB-20 EXZ2610DL CHOOSE THE BLADE Choose a suitable recommended cutting attachmentaccording to the object to be cut. • When replacing blade always be sure to use prod- ucts, which have been certified by ZENOAH. WARNING When sharpening, removing, or reattaching the blade,be sure to wear thick, sturdy ...

GB-22 EXZ2610DL 8. Operation (Optional blade usage BC-EX only) WARNING Make sure to use shoulder strap and cutting attach-ment guard. If not, it is very dangerous when you slipor lose your balance. WARNING CONTROLLING BLADE BOUNCE Blade thrust can cause serious personal injury. Care-fully study this...

GB-24 EXZ2610DL WARNING • A l w ay s w e a r ey e p ro t e c t i o n s u c h a s s a f e t ygoggles. Never lean over the rotating cutting head.Rocks or other debris could be thrown into eyesand face and cause serious personal injury. • Keep the blade guard and the mad guard attachedin place at all t...

GB-26 EXZ2610DL SPARK PLUG • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and checkthat the plug gap is in the correct range. For a re-placement plug, use the correct type specified byZENOAH. • REPLACEMENT PLUG IS A NGK CMR7H. IMPORTANT • Note that usi...

GB-28 EXZ2610DL 9. Maintenance (BC-EX only) BLADES • When refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades. • If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that theyfit more closely together. (1) Upper...

GB-31 G B EXZ2610DL TRANSMISSION • The reduction gears are lubricated by multipurpose, lithium-based grease in the transmission. At every 20hours of use, supply the transmission with new grease. • Remove the cutter holders before installing new grease to arrange for old grease to exit. NOTE • When r...

GB-32 EXZ2610DL Should any failure occur on the product under normaloperating conditions within the applicable warranty pe-riod, the failed part will be replaced or repaired free ofcharge by a ZENOAH authorized dealer. WARRANTY PERIOD: 1 year (6 months if used profes- sionally, and 30 days if used f...