Zenoah BK2651DL - Manuals - manualsarea.com

Page 2 - EC DECLARATION OF COMFORMITY; RISK OF DAMAGING HEARING; SOUND LEVEL; racing; idling; APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION

GB-2 BK2651DL EC DECLARATION OF COMFORMITY We, ZENOAH CO., LTD. 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following products referred to in thisdeclaration conform with DIRECTIVE 89/336/EEC, 98/37/EC EN ISO 11806, ISO 14865 : 1997 2000/14/EC Internal control pro...

Page 3 - SAFETY FIRST; Contents

GB-3 G B BK2651DL 1. Parts location SAFETY FIRST Instructions contained in warnings within this manual markedwith a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, andfor this reason you are requested to read all such instructionscaref...

Page 4 - Model; chine

GB-4 BK2651DL Model BK2651DL Overall size (LxWxH) mm 2621 x 414 x 330 Dry weight kg 8.3 Engine Model Zenoah G26LS Displacement cm 3 25.4 Fuel Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Carburetor Diaphragm type Ignition system Flywheel magneto (C.D.I.) Spark plug NGK BPMR 7A Fuel ...

Page 5 - WORKING CONDITION; protector; WORKING CIRCUMSTANCE; If you don’t observe the working; “USING THE PRODUCT”; For safe operation

GB-5 G B BK2651DL 1. Read this manual carefully until you completely understand andfollow all safety and operatinginstructions. 2. Keep this manual handy so that you may refer to it later when-ever any questions arise. Alsonote, if you have any questionsw h i c h c a n n o t b e a n s w e re dherein...

Page 6 - IMPORTANT

GB-6 BK2651DL ensure that neither the cuttingpar t nor the throttle come intocontact with any obstacle whenthe engine starts. WARNING Never place the throttle into thehigh-speed position when startingthe engine. 3. After starting the engine, check to make sure that the cutting at-tachment stops rota...

Page 8 - • Stop tightening the screws when the gap A be-

GB-8 BK2651DL 6. Set up INSTALLING THE SHOULDER STRAP 1. Hook the upper part of the shoulder strap at the notch on the top of the frame and pass it through the buckleas shown in the Figure, then secure it firmly. 2. Put the hook at the lower part of the shoulder strap in the strap installing locatio...

Page 11 - Right side

GB-11 G B BK2651DL NOTE • This brush cutter can be operated in either the right side or left side position. The rope guide position isfixed for right side position operation when shippedfrom the factory. • Adjust the rope guide position as shown in the figure to allow the operator in the left-hand p...

Page 12 - How to adjust the length of the shoulder strap; • Make sure to use shoulder strap and debris guard.

GB-12 BK2651DL 8. Operation PUTTING ON THE UNIT NOTE • When carrying the unit on the back, make sure that the throttle lever is set to the idling position and thatthe throttle wire will not become twisted and tensioned. 1. After confirming that there is no person or obstacle nearby, grasp the end of...

Page 13 - ADJUSTING THE LINE LENGTH

GB-13 G B BK2651DL 9. Maintenance Every Every Every 25 50 100 System/components Procedure Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔ ✔ replace, if necessary see adjusting replace carburetor idle adjustin...

Page 16 - Limited warranty; THE WARRANTY DOES NOT APPLY TO; THOSE UNITS; THIS WARRANTY DOES NOT COVER; INCLUDING THOSE OF MER-; ARE LIMITED; Troubleshooting guide

GB-16 BK2651DL Limited warranty Should any failure occur on the product under normal oper-ating conditions within the applicable warranty period, thefailed part will be replaced or repaired free of charge by aZENOAH authorized dealer. WARRANTY PERIOD: 1 year (6 months if used profession- ally, and 3...