Zenoah BCZ2610DL - Manuals - manualsarea.com

Page 2 - EXPLANATION OF SYMBOLS AND SAFETY WARNINGS; RISK OF DAMAGING HEARING; APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION; MODEL

GB-2 BCZ2610DL EXPLANATION OF SYMBOLS AND SAFETY WARNINGS WARNING!!! RISK OF DAMAGING HEARING Wear head, eye and ear protection. Husqvarna Zenoah Co., Ltd. Masahiko GOUDA 1st January 2008 BCZ2610DL 80100101 and up APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION DIRECTIVE 97/68/EC AMENDED 2002/88/E...

Page 3 - SAFETY FIRST; WARNINGS IN THE MANUAL; Contents

GB-3 G B BCZ2610DL SAFETY FIRST Instructions contained in warnings within this manual markedwith a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, andfor this reason you are requested to read all such instructionscarefully and follow t...

Page 5 - For safe operation; WORKING CONDITION; protector; WORKING CIRCUMSTANCE; If you don’t observe the working; “USING THE PRODUCT”

GB-5 G B BCZ2610DL 5. For safe operation 1. Read this manual carefully until you completely understand andfollow all safety and operatinginstructions. 2. Keep this manual handy so that you may refer to it later when-ever any questions arise. Alsonote, if you have any questionsw h i c h c a n n o t b...

Page 6 - WARNING

GB-6 BCZ2610DL 5. For safe operation contact with any obstacle whenthe engine starts. WARNING Never place the throttle into thehigh-speed position when startingthe engine. 3. After starting the engine, check to make sure that the cutting at-tachment stops rotating when thethrottle is moved fully bac...

Page 8 - SUSPENSION POINT; The handle is put during the arrow mark.

GB-8 BCZ2610DL MIN SP ACING About 48 cm SUSPENSION POINT arrow mark 6. Set up SUSPENSION POINT NOTE Be the SUSPENSION POINT inthe location of the arrow mark. INSTALLING HANDLE NOTE The handle is put during the arrow mark. • Mount the handle to the shaft tube andsuspension point itat a location that ...

Page 9 - IMPORTANT; Pay attention to agitation.

GB-9 G B BCZ2610DL 7. Fuel ■ RECOMMENDED MIXING RATIO GASOLINE 50 : OIL 1 (when using ZENOAH genuine oil) • Exhaust emission are controlled by the funda-mental engine parameters and components (eq.,carburation, ignition timing and port timing) with-out addition of any major hardware or the intro-duc...

Page 10 - Stop; Stop

GB-10 BCZ2610DL START Stop Start Stop switch WARNING The product is equipped with a centrifugal clutchmechanism, so the cutting attachment begins to ro-tate as soon as the engine is started by putting thethrottle into the start position. When starting the en-gine, place the product onto the ground i...

Page 13 - • For safety reasons, do not use metalreinforced line.

GB-13 G B BCZ2610DL 9. Maintenance BLADE • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. (A) Saw blade(B) 8-teeth blade(C) 3-teeth blade Point : 1. Keep the end corner sharp.2. Round the root of the edge, using round fil...

Page 15 - • Check the intake air cooling vent and the area

GB-15 G B BCZ2610DL Cylinder Intake air cooling vent • When checking the machine to make sure that itis okay before using it, check the area around themuffler and remove any wood chips or leavesw h i c h h a v e a t t a c h e d t h e m s e l v e s t o t h ebrushcutter. Failing to do so could cause t...

Page 16 - THE WARRANTY DOES NOT APPLY TO; THOSE UNITS; THIS WARRANTY DOES NOT COVER; INCLUDING THOSE OF MER-; ARE LIMITED

GB-16 BCZ2610DL 12. Troubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank → incorrect fuel → drain it and use correct fuel fuel filter → fuel filter is clogged → clean carburetor adjustment screw → out of normal range → adjust to normal range sparking (no spark) → spa...