Westinghouse GHP16S - Manuals

TROUBLESHOOTiNG FAULT POSSiBLE CAUSES REMEDY Burner will not light even though the sparker is working . • Knob not held down long enough in ‘High’ position for flame safeguard (where fitted) to engage • Repeat lighting procedure and hold knob down for 5 seconds in ‘High’ position (refer page 4) • Ga...

7 480mm 560mm * Gas supply connection location 830mm Gas supply connection location * 480mm Figure 4–60cm and 75cm models cut-out Figure 4–90cm models cut-out iNSTALLATiON iNSTRUCTiONS This applia nce must be installed by an authorised person and in compliance with : 1. AS 5601 ‘Gas Installations’ (...

iNSTALLATiON 1. The b ench cutout should be made as per cutout dimensions in Figure 4. 2. Adjacent walls, cupboards and protection for combustible materials. Ensure that the appliance is installed with Section 5.12.1 of AS 5601 (Australia) or section 14.1 of NZS 5261 (New Zealand), regarding clearan...

OPERATiON ON N.G./S.N.G . GAS CONNECTiON This ap pliance is supplied for use with Natural Gas. However, it can be converted for use with LPG. Refer to LP conversion on pages 12 and 13. Supply pipe sizing The total hourly gas consumption for the appliance is shown on the data label. The required supp...

CAUTION This a ppliance is fitted with Natural Gas burner injectors. Please follow the procedure below if a conversion to suit LP gas is required. The conversion kit contains appropriate LPG injectors and 1 LPG sticker. To convert to LPG 1. Remove the hotplate burners to access the hotplate injector...

TESTiNG APPLiANCE OPERATiON After installation, tes t the appliance and ensure that it operates correctly before handing it over to the customer. The following procedure is recommended: 1. Turn on the gas and electricity supply and attempt ignition on all burners, both separately and in combination....

15 Important Notice Before Calling a Service Technician please check carefully the operating instructions, service booklet and the warranty terms and conditions. FOR SERVICE or to find the address of your nearest state service centre in Australia PlEaSE Call 13 13 49 For the cost of a local call (Au...

TROUBLESHOOTiNG FAULT POSSiBLE CAUSES REMEDY Burner will not light even though the sparker is working . • Knob not held down long enough in ‘High’ position for flame safeguard (where fitted) to engage • Repeat lighting procedure and hold knob down for 5 seconds in ‘High’ position (refer page 4) • Ga...

7 480mm 560mm * Gas supply connection location 830mm Gas supply connection location * 480mm Figure 4–60cm and 75cm models cut-out Figure 4–90cm models cut-out iNSTALLATiON iNSTRUCTiONS This applia nce must be installed by an authorised person and in compliance with : 1. AS 5601 ‘Gas Installations’ (...

iNSTALLATiON 1. The b ench cutout should be made as per cutout dimensions in Figure 4. 2. Adjacent walls, cupboards and protection for combustible materials. Ensure that the appliance is installed with Section 5.12.1 of AS 5601 (Australia) or section 14.1 of NZS 5261 (New Zealand), regarding clearan...

OPERATiON ON N.G./S.N.G . GAS CONNECTiON This ap pliance is supplied for use with Natural Gas. However, it can be converted for use with LPG. Refer to LP conversion on pages 12 and 13. Supply pipe sizing The total hourly gas consumption for the appliance is shown on the data label. The required supp...

CAUTION This a ppliance is fitted with Natural Gas burner injectors. Please follow the procedure below if a conversion to suit LP gas is required. The conversion kit contains appropriate LPG injectors and 1 LPG sticker. To convert to LPG 1. Remove the hotplate burners to access the hotplate injector...

TESTiNG APPLiANCE OPERATiON After installation, tes t the appliance and ensure that it operates correctly before handing it over to the customer. The following procedure is recommended: 1. Turn on the gas and electricity supply and attempt ignition on all burners, both separately and in combination....

15 Important Notice Before Calling a Service Technician please check carefully the operating instructions, service booklet and the warranty terms and conditions. FOR SERVICE or to find the address of your nearest state service centre in Australia PlEaSE Call 13 13 49 For the cost of a local call (Au...