Vulcan VGC3632 ML-114830 - Manuals

Page 3 - TABLE OF CONTENTS

— 3 — TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 4 - UNPACKING; Do not use the door or the handle to lift the oven.; LOCATION

— 4 — Installation, Operation and Care of MODEL VGC SERIES GAS CONVEYOR OVENS PLEASE KEEP THIS MANUAL FOR FUTURE USE GENERAL Vulcan ovens are produced with quality workmanship and material. Proper installation, usage andmaintenance of your oven will result in many years of satisfactory performance. ...

Page 5 - INSTALLATION CODES AND STANDARDS; The oven must be installed in accordance with:; In the United States of America:

— 5 — When installed, minimum clearance from combustible and non-combustible construction must be 2.5"(63.5 mm) at the sides and 2.5" (63.5 mm) at the rear. The installation location must allow adequate clearances for servicing and proper operation.A minimum front clearance of 36" (914.4...

Page 8 - OPERATION; Temperature Display

— 8 — PL-41147-1 TEMPERATURE DISPLAY LOAD INDICATOR LIGHT TIME DISPLAY BELT SWITCH TIME KNOB POWER SWITCH TIME RANGE SWITCH READ SET POINT BUTTON OPERATION WARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE OVEN. CONTROLS (Fig's. 2 and 3) Fig. 2 Temper...

Page 9 - Set Point; This is a service control only. Do not touch this control.

— 9 — Belt Switch — Push switch to ON to start the conveyor belt; push to OFF to stop theconveyor belt. Power Switch — Push to ON to start the oven; push to OFF to stop the oven. When thepower switch is pushed to ON, ignition occurs automatically. Time Knob — After the Time Range Switch has been set...

Page 11 - hose down the oven. Do not use this oven if it's controls

— 11 — PL-41125-1 GAS COMBINATION CONTROL VALVE If the burner fails to light within 90 seconds, the burner control will shut off the gas combination valveand will lock out. To reset the burner control for restart, push the Power Switch to OFF and then to ON.If the burner still fails to light, turn t...

Page 12 - Turning the Oven Off; Turn Power Switch to OFF.; Extended Shutdown

— 12 — PL-41126-1 THUMB SCREWS BAFFLE Turning the Oven Off Turn Power Switch to OFF. Extended Shutdown Turn Power Switch to OFF. Turn gas combination valve to OFF. Turn main gas shutoff valve to OFF. USING THE OVEN When power is applied to the oven, it will begin operating at the factory set tempera...

Page 13 - Air Distribution Panels; DISCONNECT ELECTRICAL POWER SUPPLY BEFORE CLEANING.; Daily; Swing the bottom of the front panel out. Lower panel and pull away.

— 13 — PL-41127-1 CRUMB TRAYS Air Distribution Panels The oven is equipped with a top and a bottom air distribution panel. These panels regulate the quantityof air on the top and bottom of the product that is being cooked. They have been adjusted at the factoryfor proper baking performance. Some pro...

Page 14 - Conveyor; Retighten the nuts on the inside of the conveyor rack.; Two ways to remove the conveyor for cleaning:; Conveyor Belt Removal

— 14 — PL-41128-1 BELT TENSION SCREWS Conveyor To maintain proper belt tension the conveyor belt will have to be adjusted to remove any slack in thebelt. 1. To tension the belt, locate the two adjustment screws (Fig. 8) on the right hand end (facing machine) of the conveyor assembly. Loosen the nuts...

Page 15 - Conveyor Assembly Removal

— 15 — PL-41130 PL-41129-1 REMOVE COVER 2. Conveyor Assembly Removal a. Remove conveyor crumb trays (see Fig. 7). b. Remove cover where conveyor shaft enters the left-hand control box (Fig. 9). Fig. 9 Fig. 10 c. Lift up the drive end of the conveyor assembly and slide the conveyor assembly into the ...

Page 16 - Use a long bristle brush to clean these areas.

— 16 — PL-41131 Weekly CAUTION: Intake fans and slots on the back of the oven and control box must be cleaned weekly. Any obstructions may cause motor damage. Use a long bristle brush to clean these areas. Fig. 11 e. Pull the entire conveyor assembly from the oven (Fig. 11). f. Take conveyor assembl...

Page 19 - MAINTENANCE; THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING,; INSPECTION

— 19 — MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE OVEN. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE PERFORMING ANY MAINTENANCE ON THE OVEN. INSPECTION The oven should be inspected at least annually by a Vulcan-Hart authorized...

Page 20 - TROUBLESHOOTING; PROBLEM

— 20 — FORM 31057 (5-98) PRINTED IN U.S.A. TROUBLESHOOTING PROBLEM Power switch is on and ovenwill not operate. Burner is on but oven doesnot start. Speed control shows "OL". Conveyor belt does not turn. Conveyor belt jumps. Burner does not ignite. Cooking is not even. Oven gives off gas odo...