Vulcan VCD44 ML-138069 - Manuals

Page 2 - IMPORTANT FOR YOUR SAFETY; FOR YOUR SAFETY; IN THE EVENT OF A POWER FAILURE,

VCD SERIES CHIP WARMER F-38053 (09-10) 1 IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. FOR YOUR SAFETY DO NOT STORE OR USE GASOLIN...

Page 3 - TABLE OF CONTENTS

VCD SERIES CHIP WARMER F-38053 (09-10) 2 TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRO...

Page 4 - GENERAL; INTRODUCTION

VCD SERIES CHIP WARMER F-38053 (09-10) 3 GENERAL INTRODUCTION Vulcan-Hart Chip Warmers are produced with quality workmanship and material. Proper installation, usage, and maintenance of your warmer will result in many years of satisfactory performance. It is suggested that you thoroughly read this e...

Page 5 - ACCESS PANEL POSITIONING:

VCD SERIES CHIP WARMER F-38053 (09-10) 4 ACCESS PANEL POSITIONING: 1. Ensure that top Baffle notches are over carriage bolts. 2. Insert Access Panel onto the back of the Chip Warmer. (Fig. 1) (Fig. 1) 3. On both sides of Access Panel, place clips into slots, then lock. (Fig. 3) (Fig. 2) LEGS INSTALL...

Page 6 - ELECTRICAL REQUIREMENTS; In the United States of America:

VCD SERIES CHIP WARMER F-38053 (09-10) 5 ELECTRICAL REQUIREMENTS ELECTRICAL CODES & STANDARDS: The warmer must be installed in accordance with: In the United States of America: 1. State and Local Codes. 2. National Electrical Code, ANSI/ NFPA-70 (latest edition.) Copies may be obtained from: The...

Page 7 - OPERATION; BEFORE FIRST USE; Always disconnect; TESTING THE CHIP WARMER; The Warmer and its

VCD SERIES CHIP WARMER F-38053 (09-10) 6 OPERATION BEFORE FIRST USE The Chip Warmer should be thoroughly cleaned before initial use. Always disconnect electrical power to the Chip Warmer before cleaning or servicing. 1. Remove Access Panel by unlocking clips. 2. Place Access Panel away from Chip War...

Page 8 - OPERATION INSTRUCTIONS; SHUTDOWN; EXTENDED SHUTDOWN; SPECIFICATIONS

VCD SERIES CHIP WARMER F-38053 (09-10) 7 OPERATION INSTRUCTIONS The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. 1. Switch Power Switch to ON position. Verify that switch illuminates. 2. Open Top Door. 3. Pour chips into Baffle. Do not overfill. Th...

Page 9 - MAINTENANCE; CLEANING; STAINLESS STEEL CARE

VCD SERIES CHIP WARMER F-38053 (09-10) 8 MAINTENANCE CLEANING The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. Always unplug electrical power supply before cleaning. INTERIOR: The inside of the Chip Warmer must be cleaned each day. 1. Unplug electr...

Page 10 - Never rub in a circular motion; LOCKOUT / TAGOUT PROCEDURE; Always perform the LOCKOUT / TAGOUT

VCD SERIES CHIP WARMER F-38053 (09-10) 9 4. Never rub in a circular motion . Always rub gently in the direction of the steel grain. 5. Never leave any food products or salt on the surface. Many foods are acidic. Salt contains chloride. PRESERVING & RESTORING: Special stainless steel polishing cl...

Page 11 - TROUBLESHOOTING; SYMPTOM; SERVICE & PARTS INFORMATION; Service Parts

VCD SERIES CHIP WARMER F-38053 (09-10) 10 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE REMEDY Chip Warmer not operating Chip Warmer not plugged into power source. Plug chip warmer into correct power source as indicated on serial data plate. Lighted power switch not in ON position. Press power switch to ON...

Page 12 - WIRING DIAGRAM

VCD SERIES CHIP WARMER F-38053 (09-10) 11 WIRING DIAGRAM VCD22 & VCD44