Vulcan GCO6D ML-114729 - Manuals

– 6 – NOTICE: When the oven is mounted on casters, it must be installed with the casters supplied, a connector(not supplied by Vulcan-Hart) complying with either ANSI Z21.69 (latest edition) or CAN/CGA-6.16(latest edition), and a quick-disconnect device complying with either ANSI Z21.41 (latest edit...

– 7 – ASSEMBLING STACKED OVENS Unpack the ovens and stack kit. Position one oven on its back for access to the oven bottom, taking care notto scratch or damage it. The gas pipe protrudes beyond the back; provide for this when the oven is tipped backby resting it on suitable spacers (2 x 4's, etc.). ...

– 9 – The oven should be connected to the gas line after leveling. The gas supply line must be at least the equivalentof 3 ⁄ 4 " (19mm) iron pipe. Make sure piping is clean and free of obstructions, dirt or pipe joint compound. WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE ...

– 10 – OPERATION CONTROLS — MODELS GCO4S AND GCO4D/GCO6D (Fig. 4) Fig. 4 MASTER SWITCH — ON — turns oven control circuits on.OFF — turns oven control circuits off. OVEN COOL SWITCH — Allows the fan motor to run with the doors ajar to speed oven cooling. LIGHT SWITCH — Turns lights in the oven on or ...

– 12 – CONTROLS — MODEL GCO4C/GCO6C (Fig. 5) Fig. 5 MODEL GCO4C/GCO6C PL-51606 THERMOSTAT GAS VALVE ON / OFF / OVEN COOL 2 SPEED FAN - HI / LO LIGHT SWITCH TIMER SWITCH TURN GA S VALVE "ON" PUSH M ASTER SW ITCH T O "ON" PO STIO N. IF O VEN FAILS TO LIG HT. P USH MASTER SWIT CH TO ...

– 15 – Gentle Bake Button Selects the gentle bake time setting. A roast time must be set first. The gentle baketime can then be set equal to or less than the roast time. The gentle bake time will bethe portion of roast time to operate in the gentle bake mode. Gentle bake mode will startfirst. When g...

– 16 – ON/OFF/OVEN COOL SWITCH 1. ON turns oven control circuits on. 2. OFF turns oven control circuits off. 3. OVEN COOL allows the fan motor to run with the doors ajar to speed oven cooling. 2-SPEED FAN SWITCH Adjusts air velocity in the oven. LIGHT SWITCH Turns lights in the oven on or off. GAS V...

– 17 – USING THE GCO4C/GCO6C OVEN Preheating 1. Turn On/Off/Oven Cool switch to ON position. The Heat light will come on, indicating that power to the ovenis on. 2. Set Thermostat as desired. Refer to COOKING GUIDELINES for suggested temperatures and times forvarious products. 3. Prepare product and...

– 18 – ROAST AND HOLD OPERATION Roast and Hold cooks the product in two stages. During First Stage Cooking, the oven temperature is regulatedby the Roast thermostat for the amount of time set on the Timer. After the lapsed time counts down to 00:00,Second Stage Cooking begins. During Second Stage Co...

– 20 – COOKING CHARTS Models GCO4S, GCO4D/GCO4C and GCO6D/GCO6C BAKED PRODUCTS * Some people prefer high speed for darker cheese. ** Low speed will give you a more uniform color. Product Temp. Time (min.) No. Shelves Fan Speed ( ° F) ( ° C) Sheet Cakes (5 lb. each) (2.3 kg) 300 (149) 30 5 Low Soda B...

– 21 – MEAT & FISH PRODUCTS MISCELLANEOUS PRODUCTS FOR BEST RESULTS Product to be cooked should be centered on the oven rack, and the racks should be spaced evenly within theoven cavity. It is best not to rotate the product or open the doors during the cooking cycle. Preheat oven to 50 ° (10 ° C...

– 22 – MAINTENANCE WARNING: TURN OVEN OFF AND UNPLUG POWER SUPPLY CORD BEFORE PERFORMING ANYMAINTENANCE. The fan motor comes with sealed bearings and requires no lubrication. If this oven is placed on casters, it should be connected to the supply piping with the proper disconnect deviceand restraint...

– 23 – TROUBLESHOOTING If NO IGNITION LIGHT remains lit for more than 20 seconds after three trials (Models GCO4S AND GCO4D/GCO6D), or "E-05" appears in the display after three trials (Model GCO4C/GCO6C): • Turn oven off for 5 minutes before attempting to relight. • Check gas supply valves t...

– 24 – FORM 30903 Rev. B (2-98) PRINTED IN U.S.A. NOTES