Vulcan G30TB - Manuals - manualsarea.com

Page 3 - TABLE OF CONTENTS

– 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 4 - UNPACKING

– 4 – Installation, Operation and Care of MODEL G30TB & G40TB GAS TILTING BRAISING PANS KEEP THESE INSTRUCTIONS FOR FUTURE USE GENERAL Vulcan-Hart Gas Tilting Braising Pans are installed on a tubular base and are available in two sizes.Model G30TB has a 30-gallon capacity and an 80,000 BTU/Hr. i...

Page 5 - Place tilting braising pan in the installation position.

– 5 – The installation location must allow adequate clearances for servicing and proper operation. Aminimum front clearance of 36" is required. The tilting braising pan must be installed so that the flow of combustion and ventilation air will not beobstructed. Adequate clearance for air openings...

Page 6 - When test pressures exceed; FLUE CONNECTIONS

– 6 – GAS CONNECTIONS All gas supply connections and any pipe joint compound used must be resistant to the action of propanegases. The gas inlet is located under the control panel on the left-hand side. Connect gas supply to the tilting braising pan. The gas supply line must be at least the equivale...

Page 8 - OPERATION; BEFORE FIRST USE; — Will light when ignition has occurred.; Red Temperature Light; — Push UP to raise tilting braising pan push DOWN to lower tilting

– 8 – OPERATION WARNING: THE TILTING BRAISING PAN AND ITS PARTS ARE HOT. USE CARE WHENOPERATING, CLEANING AND SERVICING THE TILTING BRAISING PAN. BEFORE FIRST USE Using a non-corrosive, grease-dissolving commercial cleaner, clean the protective metal oils from allsurface parts and the interior of th...

Page 10 - Rinse thoroughly and wipe dry with a soft clean cloth.

– 10 – CLEANING WARNING: UNPLUG THE TILTING BRAISING PAN BEFORE CLEANING. After each use, allow the tilting braising pan to cool and clean it. Keep exposed cleanable areas of thetilting braising pan clean at all times. Do not get water in electrical box or any electrical component. 1. Thoroughly was...

Page 11 - COOKING GUIDELINES; estimated numbers

– 11 – COOKING GUIDELINES The guidelines given below are suggested quantities, temperature settings, and estimated numbers of orders per load and per hour. When two temperatures are given, the first is to start the product, andthe second to finish the product. The following temperatures should be us...

Page 14 - MAINTENANCE; ADJUSTMENTS; All tilting braising pans are adjusted at the factory.; VENT

– 14 – MAINTENANCE WARNING: THE TILTING BRAISING PAN AND ITS PARTS ARE HOT. USE CARE WHENOPERATING, CLEANING AND SERVICING THE TILTING BRAISING PAN. WARNING: UNPLUG TILTING BRAISING PAN BEFORE PERFORMING ANY MAINTENANCE. ADJUSTMENTS All tilting braising pans are adjusted at the factory. At least twi...

Page 15 - TROUBLESHOOTING; PROBLEM; Burners do not come on.; POSSIBLE CAUSES; Problem with the burners. Contact your

– 15 – TROUBLESHOOTING PROBLEM Burners do not come on. Burners produce carbon deposits. POSSIBLE CAUSES 1. Gas supply to braising pan is OFF. 2. Manual gas shutoff valve is OFF. 3. Thermostat is not turned ON. 4. Pan is not in lowest position. 5. Problem with the burners. Contact your Vulcan-Hart au...