Vulcan 7019A1 ML-104497 - Manuals

Page 3 - TABLE OF CONTENTS

— 3 — TABLE OF CONTENTS MODEL 7000 SERIES OVEN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Bake Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Roast Ovens . . . . . . ....

Page 4 - MODEL 7000 SERIES BAKE OVEN CONFIGURATIONS

— 4 — MODEL 7000 SERIES BAKE OVEN CONFIGURATIONS 7086A1 7016A1 7066A1 7018A1 7088A1 7888A1

Page 7 - INSTALLATION; UNPACKING

— 7 — INSTALLATION UNPACKING Immediately after unpacking, check for possible shipping damage. If the oven is found to be damaged,save the packaging material and contact the carrier within 15 days of delivery. There may be a large label located on the front of the oven which reads, "Remove this l...

Page 9 - Optional Steam Injector Nozzles; It is important that the oven steam be low pressure (2

— 9 — These ovens can be mounted interchangeably starting with the largest section on the bottom. Thefactory shipping tags will be marked accordingly. For the purpose of stacking positions, the suffix letterat the end of the model number is your guide: T — Top SectionM — Middle Section B — Bottom Se...

Page 11 - ELECTRICAL CONNECTIONS

— 11 — ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THEAPPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCALELECTRICAL CODES. WARNING: APPLIANCES EQUIPPED WITH A FLEXIBLE ELECTRIC SUPPLY CORD AREPROVIDED WITH A THREE-PRONG GROUNDING PLUG. IT ...

Page 12 - OPERATION; C). Turn knob counterclockwise to increase heat and clockwise to; BEFORE FIRST USE

— 12 — OPERATION WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANINGOR SERVICING THE OVEN. CONTROLS (Fig. 4) Burner Valve — when opened, allows gas to flow to the oven burner. To open valve, turn knobcounterclockwise; to close valve, turn knob clockwise. Ignition Button — used...

Page 13 - LIGHTING AND SHUTTING DOWN PILOT; Turn burner valve ON and purge air from line. Turn burner valve OFF.; Shutdown

— 13 — LIGHTING AND SHUTTING DOWN PILOT 1. Turn on main gas supply. 2. Turn burner valve ON and purge air from line. Turn burner valve OFF. 3. Wait 5 minutes, then turn burner valve ON and depress ignition button. Using a lit taper, ignite oven pilot (Fig. 5). Continue to hold button in for approxim...

Page 15 - CLEANING; In and around ovens where temperatures reach 500

— 15 — CLEANING WARNING: TURN OVEN OFF AND UNPLUG THE ELECTRICAL CORD (IF APPLICABLE) BEFORECLEANING. Clean interior and exterior of oven daily with warm water and detergent solution. Rinse thoroughly andwipe dry with a soft clean cloth. Oven Inspection Window (Optional) The oven inspection window m...

Page 16 - MAINTENANCE; REPLACING OPTIONAL LAMPS; Lamps are located in the top of the oven, centered at the back.; VENT; Before calling for service, check the following:; Service and Parts Information

— 16 — MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANINGOR SERVICING THE OVEN. REPLACING OPTIONAL LAMPS WARNING: TURN OVEN OFF AND UNPLUG ELECTRICAL CORD BEFORE REPLACING LAMPS. Lamps are located in the top of the oven, centered at the back. 1. Remove (4) 10-24 s...