Vivotek IP8364-C - Manuals - manualsarea.com

Page 2 - Table of Contents; Overview

VIVOTEK 2 - User's Manual Table of Contents Overview ..................................................................................................................................................... 4 Revision History .................................................................................

Page 4 - resolution video up to 2 Megapixel.; Revision History

VIVOTEK 4 - User's Manual Overview VIVOTEK IP8364-C is a best-in-class, bullet-style network camera designed for diverse outdoor applications. Equipped with a 2MP sensor enabling viewing resolution of 1920x1080 at a smooth 30 fps, the IP8364-C is an all-in-one outdoor camera capable of capturing hig...

Page 5 - Read Before Use; ■ Ball swivel mount bracket; Symbols and Statements in this Document; NOTE; : These statements indicate situations that can be; Electrical Hazard

VIVOTEK User's Manual - 5 Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation ...

Page 6 - Front Panel

VIVOTEK 6 - User's Manual Front Panel Rear Panel Ethernet 10/100 RJ45 Plug General I/O Terminal Block IR LEDs Lens Reset Button MicroSD/SDHC Card Slot

Page 7 - Hardware Installation; The diameters of the cable holes on the rubber seal; If you prefer installing a MicroSD card as onboard storage:

VIVOTEK User's Manual - 7 Hardware Installation IMPORTANT: The diameters of the cable holes on the rubber seal are shown on the right. Please properly install the waterproof cable gland and cables through it to obtain IP66 waterproof functionality. All units are in millimeters. The cable range for t...

Page 8 - General I/O Terminal Block; devices. The pin definitions are described below.

VIVOTEK 8 - User's Manual DI/DO Diagram Please refer to the following illustration for the connection method. +12V Digital input PIN 2 Ground PIN 1 DI- DI+ General I/O Terminal Block This Network Camera provides two digital input pins that can be connected to external sensor devices. The pin definit...

Page 9 - Fasten the bracket to the camera using 3 hex socket screws.

VIVOTEK User's Manual - 9 6. Install and tighten the camera's rear cover. 7. Tighten the rubber seal, seal clamp, and cap nut of the waterproof connector. 9 8 6 7 8. Pass the cables through the center of the ball swivel mount bracket, one at a time. 9. Fasten the bracket to the camera using 3 hex so...

Page 10 - Fastening ring

VIVOTEK 10 - User's Manual 10. Loosen the fastening ring on the mount bracket, and aim the camera at the area of your interest. When done, tighten the fastening ring. Fastening ring 75º Tilt 360º Pan Ceiling Mount Wall Mount 11. Secure the Network Camera to a wall or ceiling.

Page 11 - Hardware Reset

VIVOTEK User's Manual - 11 Hardware Reset The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset :...

Page 12 - Network Deployment; When using a PoE-enabled switch; enabled switch via Ethernet cable.; PoE Switch; When using a non-PoE switch; PoE Power Injector

VIVOTEK 12 - User's Manual Network Deployment General Connection (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a sin- gle Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE- enabled switch via ...

Page 13 - Internet connection via a router; ■ HTTP port: default is 80; Internet connection with static IP; Please refer to LAN setting on page 58 for details.

VIVOTEK User's Manual - 13 Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP a...

Page 14 - Software Installation; Network Camera on the LAN.; Next; to continue the program.; Network Camera

VIVOTEK 14 - User's Manual Software Installation Installation Wizard 2 (IW2), a software included in the product CD, helps you set up your Network Camera on the LAN. 1. Install IW2 under the Software Utility directory from the software CD. Double-click the IW2 shortcut on your desktop to launch the ...

Page 15 - Ready to Use; its installation details, please refer to its related documents.

VIVOTEK User's Manual - 15 Ready to Use 1. A browser session with the Network Camera should prompt as shown below.2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For ...

Page 16 - Secure the Shooting Angle; direction of direct sunlight.

VIVOTEK 16 - User's Manual Secure the Shooting Angle When you are done with tuning the field of view and obtain a satisfactory image, tighten the fastening ring and the 3 small hex screws on the ball-swivel bracket. Orient the camera so that the protruding edge of its sunshield is positioned against...

Page 17 - Accessing the Network Camera; GPP-compatible mobile devices, and VIVOTEK recording software.; Using Web Browsers; Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN.; Enter; Live video will be displayed in your web browser.

VIVOTEK User's Manual - 17 Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN. ...

Page 18 - it is highly recommended to set a password for the Network Camera.; OK; Refresh your web browser, then install the ActiveX

VIVOTEK 18 - User's Manual ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 75. ► If you see a ...

Page 19 - open a; Tips

VIVOTEK User's Manual - 19 • Currently the Network Camera utilizes 32-bit ActiveX plugin. You CAN NOT open a management/view session with the camera using a 64-bit IE browser. • If you encounter this problem, try execute the Iexplore.exe program from C:\ Windows\SysWOW64. A 32-bit version of IE brow...

Page 20 - Using RTSP Players; players that support RTSP streaming.

VIVOTEK 20 - User's Manual Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming. Quick Time Player VLC media player VLC media player mpegable Player pvPlayer As most ISPs and players only allow RTSP streaming t...

Page 21 - Using 3GPP-compatible Mobile Devices; Video Mode

VIVOTEK User's Manual - 21 Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet. For more information on how to set up the Network Camera over the Internet, please refer to Setup the Ne...

Page 22 - Using VIVOTEK Recording Software; software or download it from

VIVOTEK 22 - User's Manual Using VIVOTEK Recording Software The product software CD also contains an ST7501 recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras. Please install the recording software; then launch the program to add the Network Camera ...

Page 23 - Main Page; Host Name; Customized button

VIVOTEK User's Manual - 23 Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC. Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window. VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website. Host N...

Page 24 - Configuration Area; 日本語; Hide Button; : The transmission protocol and media options for H.264 video

VIVOTEK 24 - User's Manual Configuration Area Client Settings : Click this button to access the client setting page. For more information, please refer to Client Settings on page 28. Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a passw...

Page 25 - Global View; The viewing region of; PTZ Panel

VIVOTEK User's Manual - 25 Global View : Click on this item to display the Global View window. The Global View window contains a full view image (the largest frame size of the captured video) and a floating frame (the viewing region of the current video stream). The floating frame allows users to co...

Page 26 - Save Picture As; : Stop the transmission of the streaming media. Click the

VIVOTEK 26 - User's Manual Video Control Buttons : Depending on the Network Camera model and Network Camera configuration, some buttons may not be available. Snapshot : Click this button to capture and save still images. The captured images will be displayed in a pop-up window. Right-click the image...

Page 28 - Client Settings; Save; on the page bottom; H.264 Protocol Options

VIVOTEK 28 - User's Manual Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer. When completed with the settings on this page, click Save on the page bottom to enable the settings. H.264 Protocol Options Depending on your network ...

Page 29 - MP4 Saving Options; Users can record live video as they are watching it by clicking; Local Streaming Buffer Time; you enter 3,000 Millisecond, the streaming will delay for 3 seconds.

VIVOTEK User's Manual - 29 MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and file name. Folder : Specify a storage destination on your PC for the recorded video files. The locatio...

Page 30 - Joystick settings; Enable Joystick; Calibrate; button; Game Controllers; list in the Windows Control panel. If you want to

VIVOTEK 30 - User's Manual Joystick settings Enable Joystick Connect a joystick to a USB port on your management computer. Supported by the plug-in (Microsoft’s DirectX), once the plug-in for the web console is loaded, it will automatically detect if there is any joystick on the computer. The joysti...

Page 31 - Buttons Configuration; different joysticks.; Assign; will pop up a dialog. Then you can assign this; Home; to confirm the configuration.

VIVOTEK User's Manual - 31 Buttons Configuration In the Button Configuration window, the left column shows the actions you can assign, and the right column shows the functional buttons and assigned actions. The number of buttons may differ from different joysticks. Please follow the steps below to c...

Page 32 - Configure Buttons; below to configure your joystick buttons:; The buttons you define should appear on

VIVOTEK 32 - User's Manual Buttons Configuration Click the Configure Buttons button, a window will prompt as shown below. Please follow the steps below to configure your joystick buttons: 1. Select a button number from the Button # pull-down menu. 2. Select a corresponding action, such as Patrol or ...

Page 33 - Click; Configuration; on the main page to enter the camera setting pages. Note that only; Basic Mode

VIVOTEK User's Manual - 33 Configuration Click Configuration on the main page to enter the camera setting pages. Note that only Administrators can access the configuration page. VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with minimal effort. To simplify th...

Page 34 - Advanced Mode; functions, please click; System > General settings; Time. When finished with the settings on this page, click; at the bottom of the page to; System; Host name

VIVOTEK 34 - User's Manual Advanced Mode Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode . If you want to set up advanced functions, please click [Advanced Mode] on the bottom ...

Page 35 - System time; : Select this option to synchronize the date and time of the Network

VIVOTEK User's Manual - 35 System time Keep current date and time : Select this option to preserve the current date and time of the Network Camera. The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off. Synchronize with computer tim...

Page 36 - System > Homepage layout; General settings; Logo graph; Custom; and the Browse field will appear.; Upload; to replace the existing logo with a new one.; to enable the settings.

VIVOTEK 36 - User's Manual System > Homepage layout Advanced Mode This section explains how to set up your own customized homepage layout. General settings This column shows the settings of your hompage layout. You can manually select the background and font colors in Theme Options (the second ta...

Page 37 - Theme Options; to choose from. The new layout will simultaneously appear in the; Preview; to enable the

VIVOTEK User's Manual - 37 Theme Options Here you can change the color of your homepage layout. There are three types of preset patterns for you to choose from. The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings. Font Color of the Video Title Background...

Page 38 - ■ Follow the steps below to set up the customed homepage:; The palette window will pop up as shown below.

VIVOTEK 38 - User's Manual ■ Follow the steps below to set up the customed homepage: 1. Click Custom on the left column. 2. Click the field where you want to change the color on the right column. 3. The palette window will pop up as shown below. 4. Drag the slider bar and click on the left square to...

Page 39 - Log server settings; Follow the steps below to set up the remote log:; Enable remote log; In the port text box, enter the port number of the remote server.; to enable the setting.; System log

VIVOTEK User's Manual - 39 System > Logs Advanced Mode This section explains how to configure the Network Camera to send the system log to a remote server as backup. Log server settings Follow the steps below to set up the remote log: 1. Select Enable remote log . 2. In the IP address text box, e...

Page 40 - Access log; area and will be overwritten when reaching a certain limit.; assistance, please provide the information listed on this page.

VIVOTEK 40 - User's Manual Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order. The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit. System > P...

Page 41 - General settings > Upgrade firmware; complete the process.; Note: Do not power off the Network Camera during the upgrade!; Follow the steps below to upgrade the firmware:; Browse...; and locate the firmware file.; Upgrade; access the Network Camera.; General settings > Reboot; during the reboot process.

VIVOTEK User's Manual - 41 System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. General settings > Upgrade firmware This feature allows you to upgrade the firmware of your Network Camera. It takes a few minutes to compl...

Page 42 - General settings > Restore; Export

VIVOTEK 42 - User's Manual General settings > Restore This feature allows you to restore the Network Camera to factory default settings. Network : Select this option to retain the Network Type settings (please refer to Network Type on page 59). Daylight Saving Time : Select this option to retain ...

Page 43 - Open the file with Microsoft; and specify the XML file to update.

VIVOTEK User's Manual - 43 3. Open the file with Microsoft ® Notepad and locate your time zone; set the start and end time of DST. When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m. on the first Sunday in Novembe...

Page 44 - Export language file; and specify your own custom language file to upload.; to update a configuration file. Please note that the model and

VIVOTEK 44 - User's Manual The following message is displayed when attempting to upload an incorrect file format. Export language file : Click to export language strings. VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文 , and 繁體中文 . Update custom l...

Page 45 - : Enter a name that will be displayed on; locations will be cleared after flip/mirror setting.

VIVOTEK User's Manual - 45 Media > Image Advanced Mode This section explains how to configure the image settings of the Network Camera. It is composed of the following four columns: General settings, Picture settings, Exposure, and Privacy mask. General settings Video title Show_timestamp_and vid...

Page 47 - Image settings; : Adjust the value for the best color temperature.; On; and confirm the setting while the white balance is being

VIVOTEK User's Manual - 47 Image settings On this page, you can tune the White balance and Image adjustment. White balance : Adjust the value for the best color temperature. ■ You may follow the steps below to adjust the white balance to the best color temperature. 1. Place a sheet of paper of white...

Page 48 - Exposure; ■ Full view: Calculate the full range of view and offer appropriate

VIVOTEK 48 - User's Manual Exposure Advanced Mode On this page, you can set the Measurement window, Exposure level, and Exposure mode. Detailed configurations will be automatically adjusted since the sensor library will automatically adjust the value according to the ambient light. Note that the Pre...

Page 49 - Exposure level; to bright). You can click and drag the semi-circular pointers on the; Exposure time; and; Gain; compensated by electrical brightness gains.; ■ Flickerless; long exposure time is satisfactory.

VIVOTEK User's Manual - 49 Exposure control:■ Exposure level : You can manually set the Exposure level, which ranges from -2.0 to +2.0 (dark to bright). You can click and drag the semi-circular pointers on the Exposure time and Gain control slide bars to specify a range of shutter time and Gain cont...

Page 50 - Please follow the steps below to setup a profile:; Enable this profile; Configure Exposure control settings in the folowing; open the Profile of exposure settings page as shown below.

VIVOTEK 50 - User's Manual Please follow the steps below to setup a profile: 1. Check Enable this profile . 2. Select the applied mode: Day mode, Night mode, or Schedule mode. Please manually enter a range of time if you choose Schedule mode. 3. Configure Exposure control settings in the folowing co...

Page 51 - Privacy mask; ■ To set the privacy mask windows, follow the steps below:; New; ► If you want to delete the

VIVOTEK User's Manual - 51 Privacy mask Advanced Mode Click Privacy Mask to open the settings page. On this page, you can block out sensitive zones to address privacy concerns. ■ To set the privacy mask windows, follow the steps below: 1. Click New to add a new window. 2. You can use the mouse curso...

Page 52 - Stream settings; The definition of multiple streams:; Viewing Window

VIVOTEK 52 - User's Manual Media > Video Advanced Mode Stream settings This Network Camera supports multiple streams with frame sizes ranging from 176 x 144 to 1920 x 1080 pixels. The definition of multiple streams: ■ Stream 1: Users can define the "Region of Interest" (viewing region) an...

Page 53 - ■ The parameters of the multiple streams:; Please follow the steps below to set up those settings for a stream:

VIVOTEK User's Manual - 53 Media > Video ► All the items in the “Region of Interest” should not be larger than the “Output Frame Size“ (current maximum resolution). ■ The parameters of the multiple streams: When completed with the settings in the Viewing Window, click Save to enable the settings ...

Page 54 - settings in the above Viewing Window sections.; Customize; and manually enter a value.

VIVOTEK 54 - User's Manual Click the stream item to display the detailed information. The maximum frame size will follow your settings in the above Viewing Window sections. This Network Camera offers real-time H.264 and MJPEG compression standards (Dual Codec) for real-time viewing. If the H.264 mod...

Page 55 - The frame rate will decrease if you select a higher resolution.; performance. The bit rates are selectable at the following rates:; : select a bit rate from the pull-down menu. The bit rate ranges from; Fixed quality; concerns. The configurable bit rate starts from 1Mbps to 40Mbps.; Customized

VIVOTEK User's Manual - 55 The frame rate will decrease if you select a higher resolution. ■ Intra frame period Determine how often for firmware to plant an I frame. The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption. ...

Page 56 - If; JPEG; ■ Frame size; ■ Video quality; ► Video quality and fixed quality refers to the; compression rate; , so a lower value will produce higher

VIVOTEK 56 - User's Manual If JPEG mode is selected, the Network Camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage...

Page 57 - Network > General settings; Network Type; LAN

VIVOTEK User's Manual - 57 Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers. ...

Page 58 - : Secondary domain name server that backups the Primary DNS.; : To access the Network Camera from the Internet, select this option

VIVOTEK 58 - User's Manual Primary DNS : The primary domain name server that translates hostnames into IP addresses. Secondary DNS : Secondary domain name server that backups the Primary DNS. Primary WINS server : The primary WINS server that maintains the database of computer names and IP addresses...

Page 59 - Camera will select other ports for the Network Camera.; is not supported by your router, you will see the following message:; user interface on your computer:; In the Add or Remove Programs dialog box, click

VIVOTEK User's Manual - 59 NOTE ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera. ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support U...

Page 60 - Universal Plug and Play; ► How does UPnP

VIVOTEK 60 - User's Manual 4. In the Networking Services dialog box, select Universal Plug and Play and click OK . 5. Click Next in the following window. 6. Click Finish . UPnP TM is enabled. ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic disco...

Page 61 - Enable IPv6; Select this option and click; to enable IPv6 settings.; Refers to Ethernet

VIVOTEK User's Manual - 61 Enable IPv6 Select this option and click Save to enable IPv6 settings. Please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft ® Internet Explorer 6.5, Mozilla Firefox 3.0 or above. When IPv6 is enab...

Page 62 - Please follow the steps below to link to an IPv6 address:; using the following address format: (Please refer to; HTTP; ► If you choose PPPoE as the Network Type, the [

VIVOTEK 62 - User's Manual Please follow the steps below to link to an IPv6 address: 1. Open your web browser. 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser. 3. The format should be: 4. Press Enter on the keyboard or click Refresh button to refresh the we...

Page 63 - Port; HTTPS port

VIVOTEK User's Manual - 63 Port HTTPS port : By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535. FTP port : The FTP server allows the user to save recorded video clips. You can utilize VIVOTEK's Installation Wizard 2 to upgrade the firmwar...

Page 64 - Network > Streaming protocols; HTTP streaming; first please refer to Security > User account on page 75 for details.; basic; : By default, the HTTP port is set to 80 and the secondary HTTP

VIVOTEK 64 - User's Manual Network > Streaming protocols Advanced Mode HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 75 for details. Authentication : Depending on your network...

Page 65 - For example, when the Access name for; The JPEG images will be displayed in your web browser.; ► Microsoft; RTSP Streaming

VIVOTEK User's Manual - 65 URL command -- http://<ip address>:<http port>/<access name for stream 1, 2, or 3> For example, when the Access name for stream 2 is set to video2.mjpg : 1. Launch Mozilla Firefox or Netscape. 2. Type the above URL command in the address bar. Press Enter ...

Page 66 - RTSP player

VIVOTEK 66 - User's Manual Authentication : Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but t...

Page 67 - Multicast settings for stream 1 and 2

VIVOTEK User's Manual - 67 Multicast settings for stream 1 and 2 : Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for stream 1 or 2. Unicast video transmission delivers a stream through point-to-point transmission; multicast,...

Page 68 - with a dynamic IP address, to have a fixed host and domain name.; Express link; Link is more convenient and easier to set up.; Please follow the steps below to enable Express Link:; Enable express link; Enter a host name for the network device and click; . If the host name has been used by

VIVOTEK 68 - User's Manual Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. Express link Expres...

Page 69 - Manual setup; DDNS: Dynamic domain name service; : Select this option to enable the DDNS setting.; I accept

VIVOTEK User's Manual - 69 Manual setup DDNS: Dynamic domain name service Enable DDNS : Select this option to enable the DDNS setting. Provider : Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.net , a free dynamic domain name service, to VIVOTEK customers. It is reco...

Page 71 - The following are the main benefits of a QoS-aware network:; Requirements for QoS; VLAN ID

VIVOTEK User's Manual - 71 Network > QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network. Quality of service guarantees are important if the network capacity is insuff...

Page 72 - treatment for example, how much bandwidth to reserve for it.

VIVOTEK 72 - User's Manual QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Se...

Page 73 - ■ The SNMP consists of the following three key components:; SNMP Configuration

VIVOTEK User's Manual - 73 Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera. The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices. ...

Page 74 - Security > User accounts; Root Password; respective fields to access the Network Camera.; Privilege Management; Account Management; Add

VIVOTEK 74 - User's Manual Security > User accounts This section explains how to enable password protection and create multiple accounts. Root Password The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Manage User column, ...

Page 75 - on higher security level.; Create and Install Certificate Method; Before using HTTPS for communication with the Network Camera, a; Certificate; must be created; Create self-signed certificate; to generate a certificate.; Certifi; to view detailed information about the certificate.

VIVOTEK User's Manual - 75 Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher security level. Create and Ins...

Page 77 - Create certificate request and install; Select the option from the; Method; to generate the certificate request.; and click on the Information bar at the top of

VIVOTEK User's Manual - 77 Create certificate request and install 1. Select the option from the Method pull-down menu. 2. Click Create certificate to proceed. 3. The following information will show up in a pop-up window after clicking Create . Then click Save to generate the certificate request. 4. ...

Page 78 - the rest of the process as CA’s instructions on their webpage.

VIVOTEK 78 - User's Manual 5 . Look for a trusted certificate authority, such as Symantec’s VeriSign Authentication Services, that issues digital certificates. Sign in and purchase the SSL certification service. Copy the certificate request from your request prompt and paste it in the CA’s signing r...

Page 79 - Convert file format from DOS to UNIX. Open; File

VIVOTEK User's Manual - 79 7. Open a new edit, paste the certificate contents, and press ENTER at the end of the contents to add an empty line. 8. Convert file format from DOS to UNIX. Open File menu > Conversions > DOS to Unix .

Page 80 - Return to the original firmware session, use the; Browse; button to locate the crt certificate file,; to enable the certification.

VIVOTEK 80 - User's Manual 9. Save the edit using the “.crt” extension, using a file name like “CAcert.crt.” 10. Return to the original firmware session, use the Browse button to locate the crt certificate file, and click Upload to enable the certification.

Page 81 - Active; Note that; button for the configuration to take effect.

VIVOTEK User's Manual - 81 11. When the certifice file is successfully loaded, its status will be stated as Active . Note that a certificate must have been created and installed before you can click on the “ Save " button for the configuration to take effect. 12.To begin an encrypted HTTPS sessi...

Page 82 - Security > Access List; General Settings; : Simultaneous live viewing for; ■ IP address: Current connections to the Network Camera.; RTSP Authentication

VIVOTEK 82 - User's Manual Security > Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming connection(s) limited to : Simultaneous live viewing for 1~10 clients (including ...

Page 83 - ■ Refresh: Click this button to refresh all current connections.; Enable access list filtering; Filter; Enable access list filtering: Check this item and click

VIVOTEK User's Manual - 83 ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access. Please note that those checked connections will only be disconnected temporarily and wi...

Page 84 - Network; Administrator IP address; Always allow the IP address to access this device

VIVOTEK 84 - User's Manual Network : This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List. The address and network mask are written in CIDR format. For example: Range : This rule allows the user to assign a range of IP addresses to the Allow/Deny...

Page 85 - The components of a protected network with 802.1x authentication:; PEAP; Please follow the steps below to enable 802.1x settings:

VIVOTEK User's Manual - 85 Security > IEEE 802.1X Advanced Mode Enable this function if your network environment uses IEEE 802.1x, which is a port-based network access control. The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802.1x settings. Th...

Page 86 - A Network Camera requests access to the protected

VIVOTEK 86 - User's Manual 3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802.1x enabled switch. The devices will then start the authentication automatically. ► The authentication process for 802.1x: 1. The Certificate Authority (CA) provides t...

Page 87 - There are two ways to enable the camera control function:

VIVOTEK User's Manual - 87 PTZ > PTZ settings This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation. There are two ways to enable the camera control function: Digital : Control the e-PTZ operation. Within a field of view,it allows users to quickly move the focus to a t...

Page 88 - Home page in the E-PTZ Mode; ■ If you have set up different

VIVOTEK 88 - User's Manual Home page in the E-PTZ Mode ■ The e-Preset Positions will also be displayed on the home page. Select one from the drop-down list, and the Network Camera will move to the selected position. ■ If you have set up different preset positions for different streams, you can selec...

Page 89 - Please follow the steps below to set up a patrol schedule:; Patrol locations

VIVOTEK User's Manual - 89 Patrol settings You can select some preset positions for the Network Camera to patrol. Please follow the steps below to set up a patrol schedule: 1. Select the preset locations on the list, and click . 2. The selected preset locations will be displayed on the Patrol locati...

Page 90 - the Network Camera will move to the selected preset position.

VIVOTEK 90 - User's Manual NOTE ► The Preset Positions will also be displayed on the Home page. Select one from the Go to menu, and the Network Camera will move to the selected preset position. ► Click Patrol: The Network Camera will patrol along the selected positions repeatedly. NOTE:

Page 91 - Event > Event settings; Help; user-defined trigger source; Event; to open the event settings window. Here you

VIVOTEK User's Manual - 91 Event > Event settings This section explains how to configure the Network Camera to responds to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notific...

Page 92 - Detect next event after

VIVOTEK 92 - User's Manual ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. ■ Detect ne...

Page 93 - ■ Camera tampering detection

VIVOTEK User's Manual - 93 ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with. To enable this function, you need to configure the Tampering Detection option first. Please refer to page 108 for detailed information. ■ M...

Page 94 - Add server; Select the item; This server requires a secure

VIVOTEK 94 - User's Manual Add server It is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated. Click Add server to open the server setting window. You can specify...

Page 95 - To verify if the email settings are correctly configured, click; Test; ■ Server name: Enter a name for the server setting.

VIVOTEK User's Manual - 95 To verify if the email settings are correctly configured, click Test . The result will be shown in a pop-up window. If successful, you will also receive an email indicating the result. Click Save server to enable the settings. Note that after you configure the first event ...

Page 97 - the media files; NAS; The following is an example of a file destination with video clips:

VIVOTEK User's Manual - 97 Network storage : Select to send the media files to a networked storage when a trigger is activated. Please refer to NAS server on page 112 for details. Note that only one NAS server can be configured. Click Save server to enable the settings. ■ SD Test: Click to test your...

Page 99 - Add media

VIVOTEK User's Manual - 99 Add media Click Add media to open the media setting window. You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System lo...

Page 100 - Save media; Media type - Video clip

VIVOTEK 100 - User's Manual ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Click Save media to enable the settings. Note that after you set up the first media server, a new column for media server will automatically display on ...

Page 101 - ■ Maximum file size

VIVOTEK User's Manual - 101 ■ Maximum file size Specify the maximum file size allowed. Some users may need to stitch the video clips together when searching and packing up forensic evidence. ■ File name prefix Enter the text that will be appended to the front of the file name. For example: Click Sav...

Page 102 - Please see the example of the Event setting page below:; ON

VIVOTEK 102 - User's Manual In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON , in order to enable the event triggering action. When completed, click the Save event button to enable the settings and click Cl...

Page 103 - Customized Script; need more information, please contact VIVOTEK technical support.

VIVOTEK User's Manual - 103 Customized Script This function allows you to upload a sample script (.xml file) to the webpage, which will save your time on configuring the settings. Please note that there is a limited number of customized scripts you can upload; if the current amount of customized scr...

Page 104 - Applications > Motion detection; ■ To delete a window, click X on the upper right corner of the window.; Motion Detection Setting 2:

VIVOTEK 104 - User's Manual Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Follow the steps below to enable motion detection:Follow the steps below to enable motion ...

Page 105 - Profile; to open the Motion Detection Profile Settings page as shown; range if you choose Schedule mode.; to enable the settings and click; Close

VIVOTEK User's Manual - 105 A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the preset threshold. If you want to configure other motion detection settings for day/night/schedule mode (e.g., for a differ...

Page 106 - ► How does motion detection work?

VIVOTEK 106 - User's Manual NOTE ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images. Pixel differences between the two frames are detected and highlighted in gray (frame C) ...

Page 107 - Applications > Digital input; redirection; exceeds the trigger threshold.

VIVOTEK User's Manual - 107 Applications > Digital input Connect Digital input devices to the camera's terminal block, the camera will automatically detect the current connection state as pulled-high or pulled-low. You may then define the triggering condition. Digital input : Select High or Low a...

Page 108 - Recording > Recording settings; Recording Settings; Insert your SD card and click here to test; ■ Recording name: Enter a name for the recording setting.

VIVOTEK 108 - User's Manual Recording > Recording settings Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings ► Please remember to format your SD card via the camera’s web console (in the Local storage . SD card management page) ...

Page 109 - settings

VIVOTEK User's Manual - 109 The alarm trigger includes: motion detection and DI detection. Please refer to Event Settings on page 92. ■ Pre-event recording and post-event recording The Network Camera has a buffer that temporarily holds data for a period of time. Therefore, when an event occurs, the ...

Page 110 - configured a NAS server, see details in the following.; NAS server; Add NAS server; Fill in the information for your server.; to check the setting. The result will be shown in the pop-up window.

VIVOTEK 110 - User's Manual 2. Destination You can select the SD card or network storage (NAS) for the recorded video files. If you have not configured a NAS server, see details in the following. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: ...

Page 111 - to complete the settings and click; be larger than 15 MegaBytes.

VIVOTEK User's Manual - 111 If successful, you will receive a test.txt file on the network storage server. 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. ■ Capacity: You can choose either the entire free space available or limit the reserved space. T...

Page 112 - Delete

VIVOTEK 112 - User's Manual To remove a recording setting from the list, select a recording name from the drop-down list and click Delete . ■ Click recording (Name) : Opens the Recording Settings page to modify. ■ Click ON (Status) : The Status will become OFF and stop recording. ■ Click NAS (Destin...

Page 113 - Local storage > SD card management; SD card staus; card when using for the first time.; SD card control; When the maximum; to enable your settings.; no SD card

VIVOTEK User's Manual - 113 Local storage > SD card management This section explains how to manage the local storage on the Network Camera. Here you can view SD card status, and implement SD card control. SD card staus This column shows the status and reserved space of your SD card. Please rememb...

Page 114 - Local storage > Content management; can search and view the records and view the searched results.; Searching and Viewing the Records; and click; button, all recorded data will be listed in the; Search Results; ■ File attributes: Select one or more items as your search criteria.; Search

VIVOTEK 114 - User's Manual Local storage > Content management This section explains how to manage the content of recorded videos on the Network Camera. Here you can search and view the records and view the searched results. Searching and Viewing the Records This column allows the user to set up ...

Page 115 - Numbers of entries displayed; Click the; View; button and a media window will pop up to play back the selected file.; Click to adjust the image size; click the; Download

VIVOTEK User's Manual - 115 Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked. Click to sort the search results in either direction. Numbers of entries displayed on one page Enter a key word to filter the search r...

Page 117 - Appendix; URL Commands for the Network Camera; syntax example further down in the page.

VIVOTEK User's Manual - 117 Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based applicat...

Page 118 - General CGI URL Syntax and Parameters; servername

VIVOTEK 118 - User's Manual URL Command Document for All Series IP8364 6 3. General CGI URL Syntax and Parameters When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functionally...

Page 119 - DESCRIPTION

VIVOTEK User's Manual - 119 URL Command Document for All Series IP8364 7 4. Security Level SECURITY LEVEL SUB-DIRECTORY DESCRIPTION 0 anonymous Unprotected. 1 [view] anonymous, viewer, dido, camctrl 1. Can view, listen, talk to camera. 2. Can control DI/DO, PTZ of the camera. 4 [operator] anonymous,...

Page 120 - Get Server Parameter Values

VIVOTEK 120 - User's Manual URL Command Document for All Series IP8364 8 5. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax:http://< servername >/cgi-bin/ anonymous /getparam.cgi?[ <parameter> ] [&<parameter>…] http://<...

Page 122 - Set Server Parameter Values; return

VIVOTEK 122 - User's Manual URL Command Document for All Series IP8364 10 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax:http://< servername >/cgi-bin/ anonymous /setparam.cgi? <parameter>=<value> [&<parameter>=...

Page 123 - Only the parameters that you set and are readable will be returned.

VIVOTEK User's Manual - 123 URL Command Document for All Series IP8364 11 Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response:HTTP/1.0 ...

Page 124 - Available parameters on the server

VIVOTEK 124 - User's Manual URL Command Document for All Series IP8364 12 7. Available parameters on the server This chapter defines all the parameters which can be configured or retrieved from VIVOTEK network camera or video server. The general format of description is listed in the table below Val...

Page 125 - system

VIVOTEK User's Manual - 125 URL Command Document for All Series IP8364 13 7.1 system Group: system NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION hostname string[64] Mega-Pixel NetworkCamera 1/6 Host name of server ledoff <boolean> 0 6/6 Turn on (0) or turn off (1) all led indicators. date ...

Page 127 - NONE

VIVOTEK User's Manual - 127 URL Command Document for All Series IP8364 15 Moscow, Muscat, Baku, Tbilisi, Yerevan 180: GMT 04:30 Kabul 200: GMT 05:00 Ekaterinburg, Islamabad, Karachi, Tashkent 220: GMT 05:30 Calcutta, Chennai, Mumbai, New Delhi230: GMT 05:45 Kathmandu 240: GMT 06:00 Almaty, Novosibir...

Page 129 - Subgroup of

VIVOTEK User's Manual - 129 URL Command Document for All Series IP8364 17 time settings. This command can cooperate with other “restoreexceptXYZ” commands. When cooperating with others, the system parameters will be restored to default values except for a union of combined results. restoreexceptlang...

Page 130 - status

VIVOTEK 130 - User's Manual URL Command Document for All Series IP8364 18 language_count <integer> 9 0/7 Number of webpage languages available on the server. language_i<0~(count-1)> string[16] <blank> 0/7 Available language lists. customlanguage_maxcount <integer> 1 0/6 Maxim...

Page 131 - digital input behavior define; security

VIVOTEK User's Manual - 131 URL Command Document for All Series IP8364 19 7.3 digital input behavior define Group: di_i<0~(ndi-1)> NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION normalstate high, low high 1/1 Indicates open circuit or closed circuit (inactive status) 7.4 security Group: sec...

Page 132 - network; recommended

VIVOTEK 132 - User's Manual URL Command Document for All Series IP8364 20 7.5 network Group: network NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION preprocess <positive integer> NULL 6/6 An 32-bit integer, each bit can be set separately as follows:Bit 0 => HTTP service; Bit 1=> HTTPS ...

Page 135 - port

VIVOTEK User's Manual - 135 URL Command Document for All Series IP8364 23 7.5.4 FTP Subgroup of network : ftp NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION port 21, 1025~65535 21 6/6 Local ftp server port. 7.5.5 HTTP Subgroup of network : http NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION po...

Page 137 - type

VIVOTEK User's Manual - 137 URL Command Document for All Series IP8364 25 9For n=1, 239.128.1.100, and so on. videoport 1025 ~ 65535 5560+n*2 4/4 Multicast video port. ttl 1 ~ 255 15 4/4 Mutlicast time to live value. 7.5.8 RTP port Subgroup of network : rtp NAME VALUE DEFAULT SECURITY (get/set) DESC...

Page 138 - videoin

VIVOTEK 138 - User's Manual URL Command Document for All Series IP8364 26 1 => deny ipv4list_i<0~9> Single address: <ip address> Networkaddress: <ip address / network mask> Rangeaddress:<start ip address - end ip address> <blank> 6/6 IPv4 address list. ipv6list_i<...

Page 139 - for n channel products, and m is stream number; external

VIVOTEK User's Manual - 139 URL Command Document for All Series IP8364 27 7.7.1 video input setting per channel Group: videoin_c<0~(n-1)> for n channel products, and m is stream number NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION cmosfreq 50, 60 60 4/4 CMOS frequency. (capability.videoin....

Page 140 - pan

VIVOTEK 140 - User's Manual URL Command Document for All Series IP8364 28 camera; 0 (external), 1(built-in) Bit 2 => Support pan operation; 0(not support), 1(support) Bit 3 => Support tilt operation; 0(not support), 1(support) Bit 4 => Support zoom operation; 0(not support), 1(support) Bit ...

Page 141 - Video resolution in pixels.

VIVOTEK User's Manual - 141 URL Command Document for All Series IP8364 29 svc is only supported with stream 0. s<0~(m-1)>_resolution "176~1920"x"1 44~1080" 1920x1080 1/4 Video resolution in pixels. s<0~(m-1)>_h264_intraperiod 250, 500, 1000, 2000, 3000, 4000 1000 4/4 Intr...

Page 142 - framerate

VIVOTEK 142 - User's Manual URL Command Document for All Series IP8364 30 s<0~(m-1)>_h264_maxframe 1~25, 26~30 (only for 60Hz CMOS) 15 1/4 Set maximum frame rate in fps (for h264). s<0~(m-1)>_h264_profile 0~2 1 1/4 Indicate H264 profiles 0: baseline 1: main profile 2: high profile s<0...

Page 144 - video input preview; videoinpreview

VIVOTEK 144 - User's Manual URL Command Document for All Series IP8364 32 enableblc <boolean> 0 4/4 Enable backlight compensation. whitebalance auto, manual, rbgain auto 4/4 “auto” indicates auto white balance.“manual” indicates keep current value. “rbgain” indicates using rgain rgain 0~100 30...

Page 145 - ircutcontrol; image setting per channel; for n channel products

VIVOTEK User's Manual - 145 URL Command Document for All Series IP8364 33 7.9 IR cut control Group: ircutcontrol (capability.nvideoinprofile > 0) NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION mode auto, day, night, di, schedule auto 6/6 Set IR cut control mode daymodebegintime 00:00~23:59 07:...

Page 147 - image setting for preview

VIVOTEK User's Manual - 147 URL Command Document for All Series IP8364 35 spercent percentage. Softer 0 <-> 100 Sharper profile_i0_lowlightmode <boolean> 1 6/99 Enable/disable low light mode. profile_i0_gammacurve 0, 45 , 50, 60, 70, 80, 90, 100 0 4/4 Gamma curve. 7.11 image setting for ...

Page 148 - Time Shift settings; timeshift; , c for n channel products, m is stream number; Motion detection settings; for n channel product

VIVOTEK 148 - User's Manual URL Command Document for All Series IP8364 36 7.13 Time Shift settings Group: timeshift , c for n channel products, m is stream number NAME VALUE DEFAULT SECURIT Y(get/set) DESCRIPTION enable <boolean> 0 4/4 Enable time shift streaming. c<0~(n-1)>_s<0~(m-1)...

Page 149 - Tampering detection settings

VIVOTEK User's Manual - 149 URL Command Document for All Series IP8364 37 dule profile is applied to. i<0~(m-1)>_begintime hh:mm 18:00 4/4 Begin time of schedule mode. i<0~(m-1)>_endtime hh:mm 06:00 4/4 End time of schedule mode. i<0~(m-1)>_win_i<0~2>_enable <boolean> 0...

Page 150 - ddns

VIVOTEK 150 - User's Manual URL Command Document for All Series IP8364 38 7.16 DDNS Group: ddns NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION enable <boolean> 0 6/6 Enable or disable the dynamic DNS. provider Safe100, DyndnsDynamic, DyndnsCustom, DynInterfree, CustomSafe100, PeanutHull Dyn...

Page 151 - setparamlevel; UPnP presentation; upnppresentation; UPnP port forwarding; upnpportforwarding

VIVOTEK User's Manual - 151 URL Command Document for All Series IP8364 39 active.“badnetwork” : Express Link is not supported under this network environment. url string[63] <blank> 6/6 The URL to connect to this camera by express link. setparamlevel 0~2 0 6/6 Show log of parameter setting. 0: ...

Page 152 - syslog

VIVOTEK 152 - User's Manual URL Command Document for All Series IP8364 40 7.19 System log Group: syslog NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION enableremotelog <boolean> 0 6/6 Enable remote log. serverip <ipaddress> <blank> 6/6 Log server IP address. serverport 514, 1025~...

Page 153 - layout

VIVOTEK User's Manual - 153 URL Command Document for All Series IP8364 41 encryptpwro string[8~128] <blank> 6/6 Read only password encrypttyperw DES DES 6/6 Read/write encryption type encrypttypero DES DES 6/6 Read only encryption type rwcommunity string[31] Private 6/6 Read/write community ro...

Page 154 - capability

VIVOTEK 154 - User's Manual URL Command Document for All Series IP8364 42 7.22 Privacy mask Group: privacymask_c<0~(n-1)> for n channel product NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION enable <boolean> 0 4/4 Enable privacy mask. win_i<0~4>_enable <boolean> 0 4/4 Enab...

Page 156 - windowless

VIVOTEK 156 - User's Manual URL Command Document for All Series IP8364 44 0(not support), 1(support) Bit 6 => Support iris operation; 0(not support), 1(support) Bit 7 => External or built-in PT; 0(built-in), 1(external) Bit 8 => Invalidate bit 1 ~ 7; 0(bit 1 ~ 7 are valid), 1(bit 1 ~ 7 are ...

Page 159 - Tx

VIVOTEK User's Manual - 159 URL Command Document for All Series IP8364 47 audioin_codec NULL,g711 <blank> 0/7 Available codec list for audio input. uart_httptunnel <boolean> 0 0/7 Indicate whether to support HTTP tunnel for UART transfer. camctrl_httptunnel <boolean> 0 0/7 The attr...

Page 161 - Customized event script

VIVOTEK User's Manual - 161 URL Command Document for All Series IP8364 49 localstorage_seamless <boolean> 0 0/7 Indicate whether seamless recording is supported. localstorage_modnum 0, <positive integer> 0 0/7 The maximum MOD connection numbers. adaptiverecording <boolean> 1 0/7 In...

Page 164 - Server setting for event action

VIVOTEK 164 - User's Manual URL Command Document for All Series IP8364 52 7.26 Server setting for event action Group: server_i <0~4> PARAMETER VALUE DEFAULT SECURITY (get/set) DESCRIPTION name string[40] <blank> 6/6 Identification of this entry type email, ftp,http,ns email 6/6 Indicate ...

Page 165 - Media setting for event action

VIVOTEK User's Manual - 165 URL Command Document for All Series IP8364 53 7.27 Media setting for event action Group: media_i<0~4> PARAMETER VALUE DEFAULT SECURITY (get/set) DESCRIPTION name string[40] <blank> 6/6 Identification of this entry type snapshot, systemlog, videoclip, recordmsg...

Page 169 - Storage management setting; n is the total number of storage devices.; Region of interest

VIVOTEK User's Manual - 169 URL Command Document for All Series IP8364 57 stateorprovincename string[128] Asia 6/6 State or province name in the certificate information. localityname string[128] Asia 6/6 The locality name in the certificate information. organizationname string[64] VIVOTEK Inc. 6/6 O...

Page 170 - for n channel product.

VIVOTEK 170 - User's Manual URL Command Document for All Series IP8364 58 7.32 ePTZ setting Group: eptz_c<0~(n-1)> for n channel product. PARAMETER VALUE DEFAULT SECURITY (get/set) DESCRIPTION osdzoom <boolean> 1 1/4 Indicates multiple of zoom in is “on-screen display” or not smooth <...

Page 172 - Query Status of the Digital Input; Note: This request requires Viewer privileges

VIVOTEK 172 - User's Manual URL Command Document for All Series IP8364 60 8. Useful Functions 8.1 Query Status of the Digital Input Note: This request requires Viewer privileges Method: GET/POST Syntax:http://< servername >/cgi-bin/dido/getdi.cgi?[di0][&di1][&di2][&di3] If no param...

Page 173 - Capture Single Snapshot

VIVOTEK User's Manual - 173 URL Command Document for All Series IP8364 61 8.2 Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax:http://< servername >/cgi-bin/viewer/video.jpg?[channel=<value>][&resolution=<value>] [&quality=...

Page 174 - Account Management

VIVOTEK 174 - User's Manual URL Command Document for All Series IP8364 62 8.3 Account Management Note: This request requires Administrator privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/admin/editaccount.cgi ? method=<value>&username= <name> [&userpass= ...

Page 175 - This request require Administrator privileges.; Upgrade Firmware; This request requires Administrator privileges.

VIVOTEK User's Manual - 175 URL Command Document for All Series IP8364 63 8.4 System Logs Note: This request require Administrator privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/admin/syslog.cgi Server will return the most up-to-date system log. Return:HTTP/1.0 200 OK\r\n C...

Page 176 - ePTZ Camera Control

VIVOTEK 176 - User's Manual URL Command Document for All Series IP8364 64 8.6 ePTZ Camera Control Note: This request requires camctrl privileges. Method: GET/POST Syntax:http://< servername >/cgi-bin/camctrl/eCamCtrl.cgi?channel=<value>&stream=<value> [&move=<value>] ...

Page 177 - resolution

VIVOTEK User's Manual - 177 URL Command Document for All Series IP8364 65 zoom wide Zoom larger view with current speed. tele Zoom further with current speed. zooming wide or tele Zoom without stopping for larger view or further view with zs speed, used for joystick control. zs 0 ~ 6 Set the speed o...

Page 178 - ePTZ Preset Locations

VIVOTEK 178 - User's Manual URL Command Document for All Series IP8364 66 8.7 ePTZ Recall Note: This request requires camctrl privileges. Method: GET/POST Syntax:http://< servername >/cgi-bin/camctrl/eRecall.cgi?channel=<value>&stream=<value>& recall=<value>[&retu...

Page 181 - See Event/control tunnel spec for detail information; Get SDP of Streams; Open the Network Stream; This request requires Viewer access privileges.

VIVOTEK User's Manual - 181 URL Command Document for All Series IP8364 69 x-sessioncookie: string[22] content-type: application/x-vvtk-tunnelledpragma : no-cache cache-control : no-cache content-length: 32767 expires: Sun, 9 Jam 1972 00:00:00 GMT User must use GET and POST to establish two channels ...

Page 182 - search

VIVOTEK 182 - User's Manual URL Command Document for All Series IP8364 70 rtsp://< servername >/<network_rtsp_s<0~m-1>_accessname> “m” is the stream number. For details on streaming protocol, please refer to the “control signaling” and “data format” documents. 8.13 Storage manageme...

Page 183 - delete

VIVOTEK User's Manual - 183 URL Command Document for All Series IP8364 71 resolution <text> Optional. Indicate the media file resolution. Please embrace your input value with single quotes. Ex. resolution=’800x600’ isLocked <boolean> Optional. Indicate if the file is locked or not. 0: fi...

Page 184 - update; stormgr

VIVOTEK 184 - User's Manual URL Command Document for All Series IP8364 72 Ex. label=1 Ex. Delete records whose key numbers are 1, 4, and 8. http://< servername >/cgi-bin/admin/lsctrl.cgi?cmd=delete&label=1&label=4&label=8 Command: update PARAMETER VALUE DESCRIPTION label <intege...

Page 186 - motion; Ex. Local storage status in javascript format.

VIVOTEK 186 - User's Manual URL Command Document for All Series IP8364 74 < triggerType > motion </ triggerType > < mediaType > videoclip </ mediaType > < destPath > /mnt/auto/NCMF/abc/abc.jpg </ destPath > < resolution > 800x600 </ resolution > < i...

Page 188 - Virtual input; milliseconds

VIVOTEK 188 - User's Manual URL Command Document for All Series IP8364 76 Ex. http:// < servername > /cgi-bin/admin/ jpegtoavi.cgi ?resolution=800x600&fps=1&list=’/mnt/auto/CF/NCMF/video1650.jpg’, ’/mnt/auto/C F/NCMF/video1651.jpg’, ’/mnt/auto/CF/NCMF/video1652.jpg’, 8.14 Virtual input...

Page 189 - Open Timeshift Stream

VIVOTEK User's Manual - 189 URL Command Document for All Series IP8364 77 2. setvi.cgi?vi3=0 VI index is out of range. 3. setvi.cgi?vi=1 No VI index is specified. 503 The resource is unavailable, ex. Virtual input is waiting for next state. Examples: 1. setvi.cgi?vi0=0(15000)1 2. setvi.cgi?vi0=1 Req...

Page 192 - Available language lists.

VIVOTEK 192 - User's Manual URL Command Document for All Series IP8364 80 8.17 Export Files Note: This request requires Administrator privileges. Method: GET Syntax:For daylight saving time configuration file: http://< servername >/cgi-bin/admin/exportDst.cgi For language file: http://< ser...

Page 195 - Technology License Notice

VIVOTEK User's Manual - 195 Technology License Notice AMR-NB Standard THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE AGREEMENT. WITH RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING LICENSORS’ PATENTS MAY APPLY:TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 64...

Page 196 - FCC Statement; case the user may be required to take adequate measures.; VCCI Warning; 取扱説明書に従って正しい取り扱いをして下さい; Liability

VIVOTEK 196 - User's Manual Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions. ■ This device may not cause harmful interference, and■ This device must accept any interference received, including interfe...