Vivotek IP8162 - Manuals

VIVOTEK User's Manual - 5 Read Before Use The use of surveillance devices may be prohibited by law in your country� The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system� It is the user’s responsibility to ensure that the operation ...

VIVOTEK 6 - User's Manual Physical Description Front Panel Back Panel Lens General I/O Terminal Block This Network Camera provides a general I/O terminal block which is used to connect external input / output devices. The pin definitions are described below. The 24V AC can be used as an alternate po...

VIVOTEK User's Manual - 7 DI/DO Diagram Please refer to the following illustration for the connection method� 12V +12V Digital output PIN 1Power+12V PIN 2 Digital input PIN 3 Ground PIN 4 Status LED The LED indicates the status of the Network Camera� Item LED status Description 1 Steady Red Power on...

VIVOTEK 8 - User's Manual Hardware Reset The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again� Reset : ...

VIVOTEK User's Manual - 9 Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection � 1� If you have external devices such as sensors and alarms, connect them to the general I/O terminal block� 2� Connect th...

VIVOTEK 10 - User's Manual Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below� 1� Connect your Network Camera behind a router, the Internet environment is illustrated below� Regarding how to obtain your IP a...

VIVOTEK User's Manual - 11 Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enable...

VIVOTEK 12 - User's Manual Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double click the IW2 shortcut on your desktop to ...

VIVOTEK User's Manual - 13 Ready to Use 1� Access the Network Camera on the LAN�2� Retrieve live video through a web browser or the included ST-7501 recording software� 3� Unscrew the zoom controller to adjust the zoom factor� Upon completion, tighten the zoom controller� 4� Unscrew the focus contro...

VIVOTEK 14 - User's Manual 1 3 2 4 Lens mounting screw CS-mounting ring Fine-tune the CS-Mount 1�Detach the CS-mount lens from the camera body�2�Turn the right side of the camera body up�3�Use the supplied L-type hex key wrench to loosen the lens mounting screw; the CS mount ring becomes rotatable� ...

VIVOTEK 16 - User's Manual Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on th...

VIVOTEK User's Manual - 17 ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 72� ► If you see a ...

VIVOTEK 18 - User's Manual Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player mpegable Player pvPlayer As most ISPs and players only allow RTSP streaming throug...

VIVOTEK User's Manual - 19 Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Ne...

VIVOTEK 20 - User's Manual Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera to the Cha...

VIVOTEK User's Manual - 21 Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website� Host N...

VIVOTEK 22 - User's Manual Focus Assist_ There are two options for you to fine-tune the camera focus. You can either connect the camera to an analog display device, or adjust the focus through networking. Please follow the steps below: ■ Analog video output (BNC) 1� Connect the analog display device...

VIVOTEK User's Manual - 23 Configuration Area Client Settings : Click this button to access the client setting page. For more information, please refer to Client Settings on page 27� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a passw...

VIVOTEK 24 - User's Manual Frame Rate Level: SVC The camera supports the latest SVC-T (Scalable Video Coding - Temporal) feature� The SVC feature enables streaming of videos for multiple clients from one single set of layered IP packets� Designed for saving bandwidth and CPU load on client stations,...

VIVOTEK User's Manual - 25 Video and Audio Control Buttons : Depending on the Network Camera model and Network Camera configuration, some buttons may not be available. Snapshot : Click this button to capture and save still images. The captured images will be displayed in a pop-up window� Right-click...

VIVOTEK User's Manual - 27 Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer� When completed with the settings on this page, click Save on the page bottom to enable the settings� H.264 / MPEG-4 Media Options Select to stream vid...

VIVOTEK 28 - User's Manual MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and file name. Folder : Specify a storage destination for the recorded video files. File name prefix: Ente...

VIVOTEK User's Manual - 29 Configuration Click Configuration on the main page to enter the camera setting pages� Note that only Administrators can access the configuration page. VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with minimal effort. To simplify th...

VIVOTEK 30 - User's Manual Advanced Mode Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode � If you want to set up advanced functions, please click [Advanced Mode] on the bottom ...

VIVOTEK User's Manual - 31 System time Keep current date and time : Select this option to preserve the current date and time of the Network Camera� The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off� Synchronize with computer tim...

VIVOTEK 32 - User's Manual System > Homepage layout Advanced Mode This section explains how to set up your own customized homepage layout� General settings This column shows the settings of your hompage layout� You can manually select the background and font colors in Theme Options (the second ta...

VIVOTEK User's Manual - 33 Theme Options Here you can change the color of your homepage layout� There are three types of preset patterns for you to choose from� The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings� Font Color of the Video Title Background...

VIVOTEK 34 - User's Manual ■ Follow the steps below to set up the customed homepage: 1� Click Custom on the left column� 2. Click the field where you want to change the color on the right column. 3� The palette window will pop up as shown below� 4� Drag the slider bar and click on the left square to...

VIVOTEK User's Manual - 35 System > Logs Advanced Mode This section explains how to configure the Network Camera to send the system log to a remote server as backup� Log server settings Follow the steps below to set up the remote log: 1� Select Enable remote log � 2� In the IP address text box, e...

VIVOTEK 36 - User's Manual Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order� The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit� System > P...

VIVOTEK User's Manual - 37 System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc� General settings > Upgrade firmware This feature allows you to upgrade the firmware of your Network Camera� It takes a few minutes to compl...

VIVOTEK 38 - User's Manual General settings > Restore This feature allows you to restore the Network Camera to factory default settings� Network : Select this option to retain the Network Type settings (please refer to Network Type on page 54)� Daylight Saving Time : Select this option to retain ...

VIVOTEK User's Manual - 39 3. Open the file with Microsoft ® Notepad and locate your time zone; set the start and end time of DST� When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m. on the first Sunday in Novembe...

VIVOTEK 40 - User's Manual The following message is displayed when attempting to upload an incorrect file format. Export language file : Click to export language strings. VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文 , and 繁體中文 � Update custom l...

VIVOTEK User's Manual - 41 Media > Image Advanced Mode This section explains how to configure the image settings of the Network Camera� It is composed of the following four columns: General settings, Picture settings, Exposure, and Privacy mask� General settings Show information in videos and sna...

VIVOTEK User's Manual - 43 Picture settings On this page, you can tune the White balance, Image adjustment and WDR enhanced � White balance : Adjust the value for the best color temperature. ■ Auto: It will automatically adjust the color temperature of the light in response to different light source...

VIVOTEK 44 - User's Manual ■ Enable low light compensation: Select this option in low light mode, and the values of sharpness and brightness will change automatically as the noise reduction function� WDR enhanced : This function allows users to identify more objects in the high contrast environment ...

VIVOTEK User's Manual - 45 Measurement Window : This function allows user to set measurement window(s) for low light compesation� ■ Full view: Calculate the full range of view and offer appropriate light compesation� ■ Custom: This option allows you to manually add customized windows as inclusive or...

VIVOTEK 46 - User's Manual (long depth of field). • The smallest number, 1, means the iris is open as wide as possible (largest amount of light received with shortest depth of field) � • The largest number, 100, means the iris is narrowed down as much as possible (smallest amount of light received w...

VIVOTEK User's Manual - 47 Privacy mask Advanced Mode Click Privacy Mask to open the settings page� On this page, you can block out sensitive zones to address privacy concerns� ■ To set the privacy mask windows, follow the steps below: 1� Click New to add a new window� 2� You can use the mouse curso...

VIVOTEK 48 - User's Manual Media > Video Stream settings This Network Camera supports multiple streams with frame size ranging from 176 x 144 to 1920 x 1080� The definition of multiple streams: ■ Stream 1: Users can define the "Region of Interest" (viewing region) and the "Output Fram...

VIVOTEK User's Manual - 49 NOTE ► All the items in the “Region of Interest” should not be larger than the “Output Frame Size“ (current maximum resolution)� ■ The parameters of the multiple streams: When completed with the settings in the Viewing Window, click Save to enable the settings and click Cl...

VIVOTEK 50 - User's Manual Click the stream item to display the detailed information� The maximum frame size will follow your settings in the above Viewing Window sections� This Network Camera offers real-time H�264, MPEG-4 and MJEPG compression standards (Triple Codec) for real-time viewing� Stream...

VIVOTEK User's Manual - 51 The frame rate will decrease if you select a higher resolution� ■ Intra frame period Determine how often to plant an I frame� The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption� Select the in...

VIVOTEK 52 - User's Manual Fixed quality: On the other hand, if Fixed quality is selected, all frames are transmitted with the same quality; bandwidth utilization is therefore unpredictable� The video quality can be adjusted to the following settings: Medium, Standard, Good, Detailed, and Excellent....

VIVOTEK User's Manual - 53 Media > Audio Audio Settings Mute : Select this option to disable audio transmission from the Network Camera to all clients. Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page. In that case, the follow...

VIVOTEK 54 - User's Manual Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers� ...

VIVOTEK User's Manual - 55 Primary DNS : The primary domain name server that translates hostnames into IP addresses. Secondary DNS : Secondary domain name server that backups the Primary DNS. Primary WINS server : The primary WINS server that maintains the database of computer names and IP addresses...

VIVOTEK 56 - User's Manual NOTE ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera� ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support U...

VIVOTEK User's Manual - 57 4� In the Networking Services dialog box, select Universal Plug and Play and click OK � 5� Click Next in the following window� 6� Click Finish � UPnP TM is enabled� ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic disco...

VIVOTEK 58 - User's Manual Enable IPv6 Select this option and click Save to enable IPv6 settings� Please note that this only works if your network environment and hardware equipment support IPv6� The browser should be Microsoft ® Internet Explorer 6�5, Mozilla Firefox 3�0 or above� When IPv6 is enab...

VIVOTEK User's Manual - 59 Please follow the steps below to link to an IPv6 address: 1� Open your web browser� 2� Enter the link-global or link-local IPv6 address in the address bar of your web browser� 3. The format should be: 4� Press Enter on the keyboard or click Refresh button to refresh the we...

VIVOTEK 60 - User's Manual Port HTTPS port : By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535� Two way audio port : By default, the two way audio port is set to 5060. Also, it can also be assigned to another port number between 1025 and ...

VIVOTEK User's Manual - 61 2011/06/09 17:08:56 Audio is being transmitted to the Network Camera Mute Mic Volume Talk Button Click to enable audio transmission to the Network Camera; click to adjust the volume of microphone; click to turn off the audio� To stop talking, click again� FTP port : The FT...

VIVOTEK 62 - User's Manual Network > Streaming protocols Advanced Mode HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 72 for details� Authentication : Depending on your network...

VIVOTEK User's Manual - 63 URL command -- http://<ip address>:<http port>/<access name for stream 1 ~ 5> For example, when the Access name for stream 2 is set to video2�mjpg : 1� Launch Mozilla Firefox or Netscape� 2� Type the above URL command in the address bar� Press Enter � 3� ...

VIVOTEK 64 - User's Manual Authentication : Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but t...

VIVOTEK User's Manual - 65 Multicast settings for stream 1 ~ 4: Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for stream 1 ~ 4. Unicast video transmission delivers a stream through point-to-point transmission; multicast, on ...

VIVOTEK 66 - User's Manual Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera� DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. Express link Expres...

VIVOTEK User's Manual - 67 Manual setup DDNS: Dynamic domain name service Enable DDNS : Select this option to enable the DDNS setting. Provider : Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.net , a free dynamic domain name service, to VIVOTEK customers� It is reco...

VIVOTEK 68 - User's Manual [Register] Successfully Your account information has been mailed to registered e-mail address 4� Select Enable DDNS and click Save to enable the setting� ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrato...

VIVOTEK User's Manual - 69 Network > QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network� Quality of service guarantees are important if the network capacity is insuff...

VIVOTEK 70 - User's Manual QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer)� The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Se...

VIVOTEK User's Manual - 71 Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera� The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices� ...

VIVOTEK 72 - User's Manual Security > User Account This section explains how to enable password protection and create multiple accounts� Root Password The administrator account name is “root”, which is permanent and can not be deleted� If you want to add more accounts in the Manage User column, p...

VIVOTEK User's Manual - 73 Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer)� It helps protect streaming data transmission over the Internet on higher security level� Create and Ins...

VIVOTEK User's Manual - 75 Create certificate and install : Select this option if you want to create a certificate from a certifi - cation authority� 1� Select this option from a method pull-down menu� 2� Click Create certificate to generate the certificate. 3� The following information will appear ...

VIVOTEK 76 - User's Manual 4. The Certificate Information will automatically be displayed in the third column as shown below. You can click Property to see detailed information about the certificate. 5 . Copy the contents of the Certificate request (in PEM format). Use the contents to apply for a 3r...

VIVOTEK User's Manual - 77 NOTE ► How do I cancel the HTTPS settings? 1� Click on the Remove certificate button� 2� If you are currently running a secure connection The webpage will redirect to a non-HTTPS page automatically� Enable HTTPS Check this item to enable HTTPS communication, then select a ...

VIVOTEK 78 - User's Manual Security > Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address� General Settings Maximum number of concurrent streaming connection(s) limited to : Simultaneous live viewing for 1~10 clients (including ...

VIVOTEK User's Manual - 79 ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access� Please note that those checked connections will only be disconnected temporarily and wi...

VIVOTEK 80 - User's Manual Network : This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List� The address and network mask are written in CIDR format� For example: Range : This rule allows the user to assign a range of IP addresses to the Allow/Deny...

VIVOTEK User's Manual - 81 Security > IEEE 802.1X Advanced Mode Enable this function if your network environment uses IEEE 802�1x, which is a port-based network access control� The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802�1x settings� Th...

VIVOTEK User's Manual - 83 PTZ > PTZ settings This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation� There are two ways to enable the function:1. Digital: Control the e-PTZ operation. It allows users to quickly move the focus to a target area for close-up viewing witho...

VIVOTEK 84 - User's Manual Auto pan/patrol speed : Select the speed from 1~5 (slow/fast) to set up the Auto pan/patrol speed control� When completed with the settings of e-PTZ, click Save to enable the settings on this page� Home page in E-PTZ Mode ■ The e-Preset Positions will also be displayed on ...

VIVOTEK User's Manual - 85 Mechanical PTZ Operation (When camera is mounted on an external pan/tilt scan- ner) If you have your camera mounted and connected to an external pan/tilt head via the RS485 control lines, your can configure the Activated mode as “Mechanical�” You may then set identical con...

VIVOTEK 86 - User's Manual ■ Transparent HTTP Tunnel: HTTP tunnel is useful when exerting commands over the Internet. Response time can be significantly reduced� You can use UART commands to build a Transparent HTTP Tunnel� The UART commands will be sent through HTTP tunnel established between the R...

VIVOTEK User's Manual - 87 Patrol settings You can select some preset positions for the Network Camera to patrol� Please follow the steps below to set up a patrol schedule: 1� Select the preset locations on the list, and click � 2� The selected preset locations will be displayed on the Patrol locati...

VIVOTEK 88 - User's Manual NOTE ► The Preset Positions will also be displayed on the home page. Select one from the Go to drop-down list, and the Network Camera will move to the selected preset position. ► Click Patrol: The Network Camera will patrol among the selected preset positions continuously....

VIVOTEK User's Manual - 89 Custom command If Custom Camera (pan/tilt head or scanner) is selected as the PTZ driver, the Preset Position and PTZ Control Panel on the main page will be disabled� You will need to configure command buttons to control the PTZ scanner� Click Custom Command to open the Cu...

VIVOTEK 90 - User's Manual Event > Event settings This section explains how to configure the Network Camera to responds to particular situations (event)� A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notific...

VIVOTEK User's Manual - 91 ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. ■ Detect ne...

VIVOTEK 92 - User's Manual ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with� To enable this function, you need to configure the Tampering Detection option first. Please refer to page 106 for detailed information� ■ M...

VIVOTEK User's Manual - 93 Add server To set an event with recorded video or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated. Click Add server ...

VIVOTEK 94 - User's Manual To verify if the email settings are correctly configured, click Test � The result will be shown in a pop-up window� If successful, you will also receive an email indicating the result� Click Save server to enable the settings� To note that after you set up the first event ...

VIVOTEK 96 - User's Manual Network storage : Select to send the media files to a network storage location when a trigger is activated� Please refer to NAS server on page 110 for details� Click Save server to enable the settings� ■ SD Test: Click to test your SD card. The system will display a messag...

VIVOTEK 98 - User's Manual Add media Click Add media to open the media setting window� You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System lo...

VIVOTEK User's Manual - 99 ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Click Save media to enable the settings� To note that after you set up the first media server, a new column for media server will automatically show up o...

VIVOTEK 100 - User's Manual ■ Maximum file size Specify the maximum file size allowed. ■ File name prefix Enter the text that will be appended to the front of the file name. For example: Click Save media to enable the settings� Media type - System log Select to send a system log when a trigger is ac...

VIVOTEK User's Manual - 101 In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON, in order to enable the event triggering action� When completed, click Save event to enable the settings and click Close to exit ...

VIVOTEK 102 - User's Manual Customized Script This function allows you to upload a sample script (.xml file) to the webpage, which will save your time on configuring the settings. Please note that there is a limited number of customized scripts you can upload; if the current amount of customized scr...

VIVOTEK User's Manual - 103 Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Follow the steps below to enable motion detection:Follow the steps below to enable motion ...

VIVOTEK 104 - User's Manual A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. If you want to configure other motion detection settings for day/night/schedule mode, please click Prof...

VIVOTEK User's Manual - 105 NOTE ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images� Pixel differences between the two frames are detected and highlighted in gray (frame C) ...

VIVOTEK 106 - User's Manual Applications > DI and DO Digital input : Select High or Low to define normal status for the digital input. The Network Camera will report the current status� Digital output : Select Grounded or Open to define normal status for the digital output. The Network Camera wil...

VIVOTEK User's Manual - 107 Recording > Recording settings Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE ► Please remember to format your SD card when using it for the first time. Please refer to page 112 for detailed i...

VIVOTEK User's Manual - 109 2� Destination You can select the SD card or network storage (NAS) for the recorded video files. 1 2 3 4 Network storage path (\\server name or IP address\folder name) User name and password for your server NAS server Click Add NAS server to open the server setting window...

VIVOTEK User's Manual - 111 To remove a recording setting from the list, select a recording name from the drop-down list and click Delete � ■ Click Video (Name) : Opens the Recording Settings page to modify. ■ Click ON (Status) : The Status will become OFF and stop recording� ■ Click NAS (Destinatio...

VIVOTEK 112 - User's Manual Local storage > SD card management This section explains how to manage the local storage on the Network Camera� Here you can view SD card status, and implement SD card control� SD card staus This column shows the status and reserved space of your SD card� Please rememb...

VIVOTEK User's Manual - 113 Local storage > Content management This section explains how to manage the content of recorded videos on the Network Camera� Here you can search and view the records and view the searched results� Searching and Viewing the Records This column allows the user to set up ...

VIVOTEK 114 - User's Manual Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked� Click to sort the search results in either direction� Numbers of entries displayed on one page Enter a key word to filter the search r...

VIVOTEK 116 - User's Manual Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax� This section specifies the external HTTP-based applicat...

VIVOTEK User's Manual - 117 3. General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camer...

VIVOTEK 118 - User's Manual [&<parameter>…] http://< servername >/cgi-bin/ operator /getparam.cgi?[ <parameter> ] [&<parameter>…] http://< servername >/cgi-bin/ admin /getparam.cgi?[ <parameter> ] [&<parameter>…] Where the <parameter> shoul...

VIVOTEK User's Manual - 119 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://< servername >/cgi-bin/ anonymous /setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&update=<value>][&a...

VIVOTEK 120 - User's Manual <parameter>=<value>\r\n [<parameter pair>] Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Res...

VIVOTEK 126 - User's Manual 7.3 digital input behavior define Group: di_i<0~(ndi-1)> (capability.ndi > 0) NAME VALUE SECURITY (get/set) DESCRIPTION normalstate high, low 1/1 Indicates open circuit or closed circuit (inactive status) 7.4 digital output behavior define Group: do_i<0~(ndo-1...

VIVOTEK 142 - User's Manual piris_mode manual, indoor, outdoor 1/4 P-Iris mode. piris_sensitivity 1~10 4/4 P-Iris sensitivity for indoor and outdoor mode. piris_response 1~10 4/4 P-Iris response time for indoor and outdoor mode. piris_position 1~100 1/4 P-Iris position for manual mode. wdrc_mode 0~3...

VIVOTEK 144 - User's Manual 7.11 Image setting per channel Group: image_c<0~(n-1)> for n channel products NAME VALUE SECURITY (get/set) DESCRIPTION brightness -5~5 4/4 Adjust brightness of image according to mode settings. saturation -5~5,100 4/4 Adjust saturation of image according to mode se...

VIVOTEK User's Manual - 145 0: off 1: auto 2: always on 3:keep current value 7.12 Image setting for preview Group: imagepreview_c<0~(n-1)> for n channel products NAME VALUE SECURITY (get/set) DESCRIPTION brightness -5~5 4/4 Adjust brightness of image according to mode settings. saturation -5~5...

VIVOTEK 146 - User's Manual 7.13 Exposure window setting per channel Group: exposure_c<0~(n-1)> for n channel products NAME VALUE SECURITY (get/set) DESCRIPTION mode auto, custom, blc 4/4 The mode indicates how to decide the exposure. auto: Use full view as the only one exposure window. custom...

VIVOTEK User's Manual - 147 7.14 Audio input per channel Group: audioin_c<0~(n-1)> for n channel products (capability.audioin>0) NAME VALUE SECURITY (get/set) DESCRIPTION source micin, linein 4/4 micin => use built-in microphone input. linein => use external microphone input. mute 0, ...

VIVOTEK 148 - User's Manual 7.15 Time Shift settings Group: timeshift , c for n channel products, m is stream number (capability.timeshift > 0) NAME VALUE SECURITY (get/set) DESCRIPTION enable <boolean> 4/4 Enable time shift streaming. c<0~(n-1)>_s<0~(m-1)>_allow <boolean>...

VIVOTEK User's Manual - 149 position. i<0~(m-1)>_win_i<0~2>_width 0 ~ 320 4/4 Width of motion detection window. i<0~(m-1)>_win_i<0~2>_height 0 ~ 240 4/4 Height of motion detection window. i<0~(m-1)>_win_i<0~2>_objsize 0 ~ 100 4/4 Percent of motion detection window...

VIVOTEK User's Manual - 151 7.19 Express link Group: expresslink PARAMETER VALUE SECURITY (get/set) DESCRIPTION enable <boolean> 6/6 Enable or disable express link. state onlycheck, onlyoffline, checkonline, badnetwork 6/6 Camera will check the status of network environment and express link UR...

VIVOTEK 152 - User's Manual 7.22 System log Group: syslog NAME VALUE SECURITY (get/set) DESCRIPTION enableremotelog <boolean> 6/6 Enable remote log. serverip <IP address> 6/6 Log server IP address. serverport 514, 1025~65535 6/6 Server port used for log. level 0~7 6/6 Levels used to dist...

VIVOTEK User's Manual - 155 encrypttypero DES 6/6 Read only encryption type rwcommunity string[31] 6/6 Read/write community rocommunity string[31] 6/6 Read only community syslocation 0~128 6/6 System location syscontact 0~128 6/6 System contact 7.26 Layout configuration Group: layout (New version) N...

VIVOTEK User's Manual - 161 image_ focusassist <Boolean> 0/7 Indicate whether to support focus assist. localstorage_manageable <boolean> 0/7 Indicate whether manageable local storage is supported. localstorage_seamless <boolean> 0/7 Indicate whether seamless recording is supported....

VIVOTEK 164 - User's Manual action_ patrol _server (only for VS series) <product dependent> 0~255 6/6 Indicate the target servers to which the snapshots taken during patrol dwelling time should be sent. One bit represents one application server (server_i0~i4). bit0 (LSB) = server_i0. bit1 = se...

VIVOTEK User's Manual - 165 email_port 0~65535 6/6 Port to connect to the server. email_username string[64] 6/6 Username to log in to the server. email_passwd string[64] 6/6 Password of the user. email_senderemail string[128] 6/6 Email address of the sender. email_recipientemail string[128] 6/6 Emai...

VIVOTEK User's Manual - 169 7.35 Storage management setting Currently it’s for local storage (SD, CF card) Group: disk_i<0~(n-1)> n is the total number of storage devices. (capability.storage.dbenabled > 0) PARAMETER VALUE SECURITY (get/set) DESCRIPTION cyclic_enabled <boolean> 6/6 En...

VIVOTEK 170 - User's Manual zoomspeed -5 ~ 5 1/7 Zoom speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) autospeed 1 ~ 5 1/7 Auto pan/patrol speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) Group: eptz_c<0~(n-1)>_s<0~(m-1)> for n channel product an...

VIVOTEK 172 - User's Manual 8. Useful Functions 8.1 Drive the Digital Output (capability.ndo > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/dido/setdo.cgi?do1= <state> [&do2=<state>] [&do3=<state>][&do...

VIVOTEK User's Manual - 173 Example: Query the status of digital input 1 . Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\ndi1=1\r\n 8.3 Query Status of the Digital Output (capability.ndo > 0) Note: This requ...

VIVOTEK 174 - User's Manual \r\ndo1=1\r\n 8.4 3D Privacy Mask Note: This request requires admin user privilege <SD81X1> You can set privacy mask only at zoom 1x. To go back to zoom 1x directly, please send this cgi command: "/cgi-bin/camctrl/camposition.cgi?setzoom=0" Method: GET/POST ...

VIVOTEK User's Manual - 175 resolution> quality 1~5 3 The quality of the image. streamid 0~(m-1) <product dependent> The stream number. The server will return the most up-to-date snapshot of the selected channel and stream in JPEG format. The size and quality of the image will be set accord...

VIVOTEK 176 - User's Manual operator Operator privilege. admin Administrator privilege. Return <return page> Redirect to the page <return page> after the parameter is assigned . The <return page> can be a full URL path or relative path according to the current path. If you omit thi...

VIVOTEK User's Manual - 179 return <return page> Redirect to the page <return page> after the parameter is assigned . The <return page> can be a full URL path or relative path according to the current path. If you omit this parameter, itwill redirect to an empty page. 8.10 ePTZ Cam...

VIVOTEK 182 - User's Manual 8.13 Preset Locations (capability.ptzenabled) Note: This request requires Operator privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/operator/preset.cgi?[channel=<value>] [&addpos=<value>][&delpos=<value>][&return= <...

VIVOTEK 184 - User's Manual 8.16 UART HTTP Tunnel Channel (capability.nuart > 0) Note: This request requires Operator privileges. Method: GET and POST Syntax: http://< servername >/cgi-bin/operator/uartchannel.cgi?[channel=<value>] -----------------------------------------------------...

VIVOTEK 186 - User's Manual 8.18 Get SDP of Streams Note: This request requires Viewer access privileges. Method: GET/POST Syntax: http://< servername >/<network_rtsp_s<0~m-1>_accessname> “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1...

VIVOTEK User's Manual - 195 <product dependent> h264_bitrate 1000~8000000 1000~4000000 <product dependent> 512000 <productdependent> Set bit rate in bps when choosing cbr in “h264_ratecontrolmode”. h264_maxframe 1~25, 26~30 (only for NTSC or 60Hz CMOS) 10 15 <productdependent>...

VIVOTEK User's Manual - 197 Technical Specifications F i x e d N e t w o r k C a m e r a IP8162/62P 2-megapixel • Full HD • Focus Assist • WDR Enhanced Ver 1.0 VIVOTEK INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. | T : +886-2-82455282 | F : +886-2-82455532 | E : sa...

VIVOTEK 198 - User's Manual Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE� THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOS...

VIVOTEK User's Manual - 199 Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15� Operation is subject to the following two conditions� ■ This device may not cause harmful interference, and■ This device must accept any interference received, including interfe...