Vivotek IP8151 - Manuals

VIVOTEK User's Manual - 5 DI/DO Diagram Please refer to the following illustration for the connection method� 12V +12V Digital output PIN 1Power+12V PIN 2 Digital input PIN 3 Ground PIN 4 Status LED The LED indicates the status of the Network Camera� Item LED status Description 1 Steady Red Power on...

VIVOTEK 6 - User's Manual Hardware Reset The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again� Reset: P...

VIVOTEK User's Manual - 7 Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection � 1. If you have external devices such as sensors and alarms, connect them to the general I/O terminal block� 2� Connect th...

VIVOTEK 8 - User's Manual Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below� 1� Connect your Network Camera behind a router, the Internet environment is illustrated below� Regarding how to obtain your IP ad...

VIVOTEK User's Manual - 9 Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enabled...

VIVOTEK 10 - User's Manual Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double click the IW2 shortcut on your desktop to ...

VIVOTEK User's Manual - 11 Ready to Use 1� Access the Network Camera on the LAN�2� Retrieve live video through a web browser or recording software�

VIVOTEK 12 - User's Manual Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on th...

VIVOTEK User's Manual - 13 ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 27� ► If you see a ...

VIVOTEK 14 - User's Manual Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player mpegable Player pvPlayer As most ISPs and players only allow RTSP streaming throug...

VIVOTEK User's Manual - 15 Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Ne...

VIVOTEK 16 - User's Manual Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera to the Cha...

VIVOTEK User's Manual - 17 Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� NOTE ► “Focus Assist“ and “Iris Adjustment (P-iris)“ are not supported...

VIVOTEK 18 - User's Manual Focus Assist (IP8151P only) Please follow the steps to fine-tune the camera focus: 1. Adjust the C- or CS-mount ring and fix the shooting direction. 2. Click “on“ to enable the focus assist function, then the Live Video Window will become full screen for precise focus adju...

VIVOTEK User's Manual - 19 Configuration Area Client Settings: Click this button to access the client setting page� For more information, please refer to Client Settings on page 22� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a passwo...

VIVOTEK 20 - User's Manual Snapshot: Click this button to capture and save still images� The captured images will be displayed in a pop-up window� Right-click the image and choose Save Picture As to save it in JPEG (*�jpg) or BMP (*�bmp) format� Digital Zoom : Click and uncheck “Disable digital zoom...

VIVOTEK 22 - User's Manual Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer� When completed with the settings on this page, click Save on the page bottom to enable the settings� H.264 / MPEG-4 Media Options Select to stream vid...

VIVOTEK User's Manual - 23 MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and file name. Folder : Specify a storage destination for the recorded video files. File name prefix: Ente...

VIVOTEK 24 - User's Manual Configuration Click Configuration on the main page to enter the camera setting pages� Note that only Administrators can access the configuration page. VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with minimal effort� To simplify th...

VIVOTEK User's Manual - 25 Advanced Mode Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode � If you want to set up advanced functions, please click [Advanced Mode] on the bottom ...

VIVOTEK 26 - User's Manual System Time Keep current date and time: Select this option to preserve the current date and time of the Network Camera� The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off� Sync with computer time: Selec...

VIVOTEK User's Manual - 27 Security This section explains how to enable password protection and create multiple accounts. Root Password The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Manage User column, please apply the pa...

VIVOTEK 28 - User's Manual HTTPS (Hypertext Transfer Protocol over SSL) Advanced Mode This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer)� It helps protect streaming data transmission over the Internet on higher security level� Enable HTTPS C...

VIVOTEK User's Manual - 29 4. The Certificate Information will automatically be displayed in the third column as shown below. You can click Property to view detailed information about the certificate. 5� Click Home to return to the main page. Change the address from “ http:// ” to “ https:// “ in th...

VIVOTEK 30 - User's Manual Create self-signed certificate manually 1� Select this option� 2� Click Create to open the Create Certificate page, then click Save to generate the certificate. 3. The Certificate Information will automatically be displayed in the third column as shown below. You can click...

VIVOTEK User's Manual - 31 3� If you see the following Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups� 4. The pop-up window shows an example of a certificate request.

VIVOTEK 32 - User's Manual 5� Look for a trusted certificate authority that issues digital certificates� Enroll the Network Camera� Wait for the certificate authority to issue a SSL certificate; click Browse... to search for the issued certificate, then click Upload in the second column. NOTE ► How ...

VIVOTEK User's Manual - 33 SNMP (Simple Network Management Protocol) Advanced Mode This section explains how to use the SNMP on the network camera. The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices�...

VIVOTEK 34 - User's Manual Network This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers� The default setting fo...

VIVOTEK 36 - User's Manual NOTE ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera� ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support U...

VIVOTEK User's Manual - 37 4. In the Networking Services dialog box, select Universal Plug and Play and click OK � 5� Click Next in the following window� 6� Click Finish � UPnP TM is enabled� ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic disco...

VIVOTEK 38 - User's Manual Enable IPv6 Select this option and click Save to enable IPv6 settings� Please note that this only works if your network environment and hardware equipment support IPv6� The browser should be Microsoft ® Internet Explorer 6.5, Mozilla Firefox 3.0 or above. When IPv6 is enab...

VIVOTEK User's Manual - 39 Please follow the steps below to link to an IPv6 address: 1� Open your web browser� 2� Enter the link-global or link-local IPv6 address in the address bar of your web browser� 3� The format should be: 4� Press Enter on the keyboard or click Refresh button to refresh the we...

VIVOTEK 40 - User's Manual IEEE 802.1x Advanced Mode Enable this function if your network environment uses IEEE 802.1x, which is a port-based network access control� The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802.1x settings. The 802.1x stand...

VIVOTEK 42 - User's Manual QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network� Quality of service guarantees are important if the network capacity is insufficient, espec...

VIVOTEK User's Manual - 43 QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer)� The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Se...

VIVOTEK 44 - User's Manual HTTP Advanced Mode To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security on page 27 for details� Authentication: Depending on your network security requirements, the Network Camera provides two types ...

VIVOTEK User's Manual - 45 URL command -- http://<ip address>:<http port>/<access name for stream 1 ~ 5> For example, when the Access name for stream 2 is set to video2�mjpg : 1. Launch Mozilla Firefox or Netscape. 2� Type the above URL command in the address bar� Press Enter � 3� ...

VIVOTEK 46 - User's Manual Note that as JPEG only transmits a series of JPEG images to the client, to enable the two-way audio function, make sure the video mode is set to “MPEG-4” on the Audio and Video Settings page and the media option is set to “Video and Audio” on the Client Settings page. Plea...

VIVOTEK User's Manual - 47 RTSP Streaming To utilize RTSP streaming authentication, make sure that you have set a password for the Network Camera first; please refer to Security on page 27 for details� Authentication: Depending on your network security requirements, the Network Camera provides three...

VIVOTEK 48 - User's Manual RTSP port /RTP port for video, audio/ RTCP port for video, audio ■ RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default, the port number is set to 554� ■ The RTP (Real-time Transport Protocol) is used to deliver video and audio data to t...

VIVOTEK User's Manual - 49 DDNS This section explains how to configure the dynamic domain name service for the Network Camera� DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. DDNS: Dynamic domain name servic...

VIVOTEK 50 - User's Manual 4� Select Enable DDNS and click Save to enable the setting� ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators� You can use CustomSafe100 to register a dynamic domain name if your distributor or system ...

VIVOTEK User's Manual - 51 Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming connection(s) limited to : Simultaneous live viewing for 1~10 clients (including stream 1 and s...

VIVOTEK 52 - User's Manual ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access� Please note that those checked connections will only be disconnected temporarily and wi...

VIVOTEK User's Manual - 53 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List� For example: Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List� Note: This rule is only applied to IPv4� For example...

VIVOTEK 54 - User's Manual Audio and Video This section explains how to configure the audio and video settings of the Network Camera. It is composed of the following two columns: Video Settings and Audio Settings� Video Settings Video title: Enter a name that will be displayed on the title bar of th...

VIVOTEK User's Manual - 55 ■ Manual: This mode allows user to fine-tune the value of iris opening manually, which ranges from 1 (short depth of filed) to 100 (long depth of field). The Response time is for adjusting the opening or closing speed of the iris from 1 (quick) to 10 (slow) steps� In addit...

VIVOTEK 56 - User's Manual White balance: Adjust the value for the best color temperature� ■ Auto: It will automatically adjust the color temperature of the light in response to different light sources. The white balance setting defaults to Auto and works well in most situations� ■ Keep current valu...

VIVOTEK User's Manual - 57 ■ Enable low light compensation: Select this option in low light mode, and the values of sharpness and brightness will change automatically as the noise reduction function� You can click Preview to fine-tune the image, or click Restore to recall the original settings witho...

VIVOTEK 58 - User's Manual Exposure Settings Advanced Mode Please refer to page 54 to choose a proper power line frequency and iris mode first. Then click Exposure Settings to open the Exposure Settings page. On this page, you can set the Exposure level, Exposure management window, Exposure time, an...

VIVOTEK User's Manual - 59 Measurement Window: This function allows user to set measurement window(s) for low light compensation� ■ Full view: Calculate the full range of view and offer appropriate light compesation� ■ Custom: This option allows you to manually add customized windows as inclusive or...

VIVOTEK 60 - User's Manual If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Exposure Settings Profile Settings page as shown below. Please follow the steps below to setup a profile: 1� Check Enable this profile � 2� Select the applied mode...

VIVOTEK User's Manual - 61 Viewing Window Advanced Mode Click Viewing Window to open the Viewing Window Settings page� This Network Camera supports multiple streams with frame size ranging from 176 x 144 to 1280 x 1024. The definition of multiple streams: ■ Stream 1: Users can define the "Region...

VIVOTEK 62 - User's Manual ■ The parameters of the multiple streams: When completed with the settings in the Viewing Window, click Save to enable the settings and click Close to exit the window. The selected Output Frame Size will immediately be applied to the Frame size of each video stream� Then y...

VIVOTEK User's Manual - 63 Video Quality Settings Advanced Mode Click the stream item to display the detailed information. The maximum frame size will follow your settings in the above Viewing Window sections� This Network Camera offers real-time H�264, MPEG-4 and MJEPG compression standards (Triple...

VIVOTEK 64 - User's Manual ■ Intra frame period Determine how often to plant an I frame� The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption� Select the intra frame period from the following durations: 1/4 second, 1/2 s...

VIVOTEK 66 - User's Manual ■ Disable DO on System page; the following item will be fixed. ■ Hide DO on Home page as shown below:

VIVOTEK User's Manual - 67 Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients� Note that if mute mode is turned on, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page� In that case, the followi...

VIVOTEK 68 - User's Manual Motion Detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Follow the steps below to enable motion detection:Follow the steps below to enable motion detection: 1� Click...

VIVOTEK User's Manual - 69 A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. If you want to configure other motion detection settings for day/night/schedule mode, please click Profi...

VIVOTEK 70 - User's Manual NOTE ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage� In the illustration above, frame A and frame B are two sequential images. Pixel differences between the two frames are detected and highlighted in gray (frame C) a...

VIVOTEK User's Manual - 71 Camera Tampering Detection This section explains how to set up camera tamper detection. With tamper detection, the camera is capable of detecting incidents such as redirection , blocking or defocusing , or even spray paint � Please follow the steps below to set up the came...

VIVOTEK 72 - User's Manual Camera Control This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation. There are two ways to enable the camera control function: 1� Mechanical: Connect the Network Camera to a PTZ driver or scanner via RS485 interface� 2� Digital: Control the e-P...

VIVOTEK User's Manual - 73 Transparent HTTP Tunnel: If you want to use your own RS-485 device, you can use UART commands to build a Transparent HTTP Tunnel� The UART commands will be sent through HTTP tunnel established between the RS-485 device and the linked camera� For detailed application notes,...

VIVOTEK 74 - User's Manual Home page in Mechanical PTZ Mode ■ The Preset Positions will also be displayed on the home page� Select one from the drop-down list, and the Network Camera will move to the selected preset position� 2010/12/10 17:08:56

VIVOTEK User's Manual - 75 Patrol Settings You can select some preset positions for the Network Camera to patrol� Please follow the steps below to set up a patrol schedule: 1� Click a preset location on the list and click Select � 2� The selected preset location will be displayed on the Source list�...

VIVOTEK 76 - User's Manual Custom Command If Custom Camera (scanner) is selected as the PTZ driver, the Preset Position and PTZ Control Panel on the main page will be disabled� You will need to configure command buttons to control the PTZ scanner� Click Custom Command to open the Custom Command page...

VIVOTEK User's Manual - 77 E-PTZ Operation If you select “Digital“, the e-PTZ control settings section will be displayed as shown below: Select Stream: Select one of the stream 1~3 to set up the e-PTZ control� Please note that each stream can be set up with its own e-preset positions and e-patrol se...

VIVOTEK 78 - User's Manual Home page in E-PTZ Mode ■ The e-Preset Positions will also be displayed on the home page� Select one from the drop-down list, and the Network Camera will move to the selected e-preset position� ■ If you have set up different e- preset positions for stream 1~3, you can sele...

VIVOTEK User's Manual - 79 Homepage Layout Advanced Mode This section explains how to set up your own customized homepage layout. Preview This column shows the settings of your homepage layout� You can manually select the background and font colors in Theme Options (the third column on this page)� T...

VIVOTEK 80 - User's Manual Theme Options Here you can change the color of your homepage layout� There are three types of preset patterns for you to choose from� The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings� Font Color of the Video Title Font Color...

VIVOTEK 82 - User's Manual Application Advanced Mode This section explains how to configure the Network Camera to responds to particular situations (event)� A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notific...

VIVOTEK User's Manual - 83 Event Settings In the Event Settings column, click Add to open the Event Settings page� On this page, you can arrange three elements -- Trigger, Schedule, and Action to set an event� A total of 3 event settings can be configured. Event name: Enter a name for the event sett...

VIVOTEK 84 - User's Manual An event is an action initiated by a user-defined trigger source; it is the causal arrangement of the following three elements: Trigger, Event Schedule, and Action� Trigger This is the cause or stimulus which defines when to trigger the Network Camera. The trigger source c...

VIVOTEK User's Manual - 85 ■ Manual Trigger This option allows user to enable event triggers manually by clicking the on/off button on the homepage. Please configure 1 ~ 3 events before using this function. Event Schedule Specify the period for the event� ■ Select the days of the week. ■ Select the ...

VIVOTEK 86 - User's Manual To set an event with recorded video or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated� ■ Add Server / Add Media Cli...

VIVOTEK User's Manual - 87 When completed, click Save to enable the settings and click Close to exit Event Settings page. The new event settings / server settings / media settings will appear in the event drop-down list on the Application page� Here is an example of the Application page with an even...

VIVOTEK 88 - User's Manual Server Settings Click Add Server on Event Settings page to open the Server Setting page� On this page, you can specify where the notification messages are sent when a trigger is activated. A total of 5 server settings can be configured. Server name: Enter a name for the se...

VIVOTEK User's Manual - 89 FTP : Select to send the media files to an FTP server when a trigger is activated. ■ Server address: Enter the domain name or IP address of the FTP server. ■ Server port By default, the FTP server port is set to 21� It can also be assigned to another port number between 10...

VIVOTEK 90 - User's Manual HTTP : Select to send the media files to an HTTP server when a trigger is activated. ■ URL: Enter the URL of the HTTP server. ■ User name: Enter the user name if necessary. ■ Password: Enter the password if necessary. To verify if the HTTP settings are correctly configured...

VIVOTEK User's Manual - 91 Media Settings Click Add Media on the Event Settings page to open the Media Settings page� On this page, you can specify the type of media that will be sent when a trigger is activated� A total of 5 media settings can be configured. Media name: Enter a name for the media s...

VIVOTEK User's Manual - 93 You can continue to select a server and media type for the event� Please go back to page 66 for detailed information� ■ SD Test: Click to test your SD card� The system will display a message indicating success or failure� If you want to use your SD card for local storage, ...

VIVOTEK 94 - User's Manual The following is an example of a file destination with video clips: Click 20081120 to open the directory: 20100820 20100821 20100822 Click to delete selected items Click to delete all recorded data The format is: YYYYMMDD Click to open the directory Click to delete selecte...

VIVOTEK User's Manual - 95 Recording Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE ► Before setting up this page, please set up the Network Storage on the Server Settings page first. ► Please remember to format your SD car...

VIVOTEK 96 - User's Manual If successful, you will receive a test.txt file on the network storage server. 3� Enter a server name� 4� Click Save to complete the settings and click Close to exit the page. Recording Settings Click Add to open the recording setting page� On this page, you can define the...

VIVOTEK User's Manual - 97 The alarm trigger includes: motion detection and DI detection� Please refer to Event Settings on page 83� ■ Pre-event recording and post-event recording The Network Camera has a buffer area; it temporarily holds data up to a certain limit� Enter a number to decide the dura...

VIVOTEK 98 - User's Manual Destination : You can select the SD card or network storage that was set up for the recorded video files. Capacity: You can choose either the entire free space available or limit the reserved space� The recording size limit must be larger than the reserved amount for cycli...

VIVOTEK User's Manual - 99 Local Storage Advanced Mode This section explains how to manage the local storage on the Network Camera. Here you can view SD card status, search for recorded files to playback, download, etc. SD Card Management SD card status: This column shows the status and reserved spa...

VIVOTEK 100 - User's Manual SD card control ■ Enable cyclic storage: Check this item if you want to enable cyclic recording� When the maximum capacity is reached, the oldest file will be overwritten by the latest one. ■ Enable automatic disk cleanup: Check this item and enter the number of days you ...

VIVOTEK User's Manual - 101 Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked� Click to sort the search results in either direction� View: Click on a search result which will highlight the selected item in purple ...

VIVOTEK 102 - User's Manual Download: Click on a search result to highlight the selected item in purple as shown above� Then click the Download button and a file download window will pop up for you to save the file. JPEGs to AVI : This functions only applies to “JPEG“ format files such as snapshots....

VIVOTEK User's Manual - 103 System Log Advanced Mode This section explains how to configure the Network Camera to send the system log to the remote server as backup� Remote Log You can configure the Network Camera to send the system log file to a remote server as a log backup. Before utilizing this ...

VIVOTEK 104 - User's Manual View Parameters Advanced Mode The View Parameters page lists the entire system’s parameters in alphabetical order� If you need technical assistance, please provide the information listed on this page�

VIVOTEK User's Manual - 105 Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc� Reboot This feature allows you to reboot the Network Camera, which takes about one minute to complete� When completed, the live video page will be displa...

VIVOTEK 106 - User's Manual Export / Upload Files Advanced Mode This feature allows you to Export / Upload daylight saving time rules, custom language files, and setting backup files. Export daylight saving time configuration file : Click to set the start and end time of DST� Follow the steps below ...

VIVOTEK User's Manual - 107 Upload daylight saving time rule: Click Browse… and specify the XML file to upload. If the incorrect date and time are assigned, you will see the following warning message when uploading the file to the Network Camera. The following message is displayed when attempting to...

VIVOTEK User's Manual - 109 Appendix URL Commands for the Network Camera Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based application...

VIVOTEK 110 - User's Manual 3. General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camer...

VIVOTEK 112 - User's Manual 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://< servername >/cgi-bin/ anonymous /setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&update=<value>][&a...

VIVOTEK User's Manual - 113 <parameter>=<value>\r\n [<parameter pair>] Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Res...

VIVOTEK 118 - User's Manual uploaded to the server. customlanguage_i<0~(ma xcount-1)> string 0/6 Custom language name. 7.2 status Group: status NAME VALUE SECURITY (get/set) DESCRIPTION videoactualmodulation <product dependent> ntsc, pal 4/7 The actual modulation type (videoin.type=0). d...

VIVOTEK User's Manual - 119 7.4 digital output behavior define Group: do_i<0~(ndo-1)> (capability.ndo > 0) NAME VALUE SECURITY (get/set) DESCRIPTION normalstate open, grounded 1/1 Indicate open circuit or closed circuit (inactive status) 7.5 security Group: security NAME VALUE SECURITY (get...

VIVOTEK User's Manual - 131 policy day, night, schedule 4/4 The mode which the profile is applied to. begintime hh:mm 4/4 Begin time of schedule mode. endtime hh:mm 4/4 End time of schedule mode. exposuremode auto,fixed 4/4 Exposure Mode minexposure 1~32000 4/4 Minimum exposure time. maxexposure 1~3...

VIVOTEK User's Manual - 133 7.11 image setting per channel Group: image_c<0~(n-1)> for n channel products NAME VALUE SECURITY (get/set) DESCRIPTION brightness -5~5 4/4 Adjust brightness of image according to mode settings. saturation -5~5,100 4/4 Adjust saturation of image according to mode se...

VIVOTEK 134 - User's Manual 3:keep current value profile_i0_lowlightmode <boolean> 4/4 Enable/disable low light mode. 7.12 image setting for preview Group: imagepreview_c<0~(n-1)> for n channel products NAME VALUE SECURITY (get/set) DESCRIPTION brightness -5~5 4/4 Adjust brightness of im...

VIVOTEK User's Manual - 135 (audioin_c<0~(n-1)>_source = linein) boostmic 1~37 4/4 Enable microphone boost. 0 => +0dB 1 => +20dB 2 => +40dB Or Gain of input. (audioin_c<0~(n-1)>_source = micin) s<0~(m-1)>_codectype aac4, gamr, g711 4/4 Set audio codec type for input. s<...

VIVOTEK 136 - User's Manual 7.15 Motion detection settings Group: motion_c<0~(n-1)> for n channel product NAME VALUE SECURITY (get/set) DESCRIPTION enable <boolean> 4/4 Enable motion detection. win_i<0~2>_enable <boolean> 4/4 Enable motion window 1~3. win_i<0~2>_name st...

VIVOTEK User's Manual - 137 7.16 Tempering detection settings Group: tampering_c<0~(n-1)> for n channel product (capability.tampering > 0) NAME VALUE SECURITY (get/set) DESCRIPTION enable <boolean> 4/4 Enable or disable tamper detection. threshold 0 ~ 255 4/4 Threshold of tamper detec...

VIVOTEK 138 - User's Manual MegaChips, DLink, DLinkCN Logitec, GE_Security, HUAGAI, 3322, ALARM, ChangeIP, NOIP SWISSCOM CustomizedTZO <product dependent> Epolice => epolice.com.tw PCCW => pccw.com MegaChips => megachips.co.jp Dlink =>D-LINK DlinkCN => D-LINK CN Logitec => lo...

VIVOTEK User's Manual - 139 upnpnatstatus 0~3 6/7 The status of UPnP port forwarding, used internally. 0 = OK, 1 = FAIL, 2 = no IGD router, 3 = no need for port forwarding 7.20 System log Group: syslog NAME VALUE SECURITY (get/set) DESCRIPTION enableremotelog <boolean> 6/6 Enable remote log. s...

VIVOTEK 142 - User's Manual 7.23 Layout configuration Group: layout (New version) NAME VALUE SECURITY (get/set) DESCRIPTION logo_default <boolean> 1/6 0 => Custom logo 1 => Default logo logo_link string[40] 1/6 Hyperlink of the logo logo_powerbyvvtk_hidden <boolean> 1/6 0 => dis...

VIVOTEK User's Manual - 147 Bit 1 => stream 2 supports ePTZ or not. The rest may be deduced by analogy nanystream 0, <positive integer> 0/7 number of any media stream per channel iva <boolean> 0/7 Indicate whether to support Intelligent Video analysis tampering <boolean> 0/7 Ind...

VIVOTEK 150 - User's Manual 7.28 Server setting for event action Group: server_i <0~4> PARAMETER VALUE SECURITY (get/set) DESCRIPTION name string[40] 6/6 Identification of this entry type email, ftp, http, ns 6/6 Indicate the server type: “email” = email server “ftp” = FTP server “http” = HTTP...

VIVOTEK User's Manual - 151 7.29 Media setting for event action Group: media_i<0~4> (media_freespace is used internally.) PARAMETER VALUE SECURITY (get/set) DESCRIPTION name string[40] 6/6 Identification of this entry type snapshot, systemlog, videoclip, recordmsg 6/6 Media type to send to the...

VIVOTEK 154 - User's Manual install manual => Create self-signed certificate manually. install => Create certificate request and install. status -3 ~ 1 6/7 Specify the https status. -3 = Certificate not installed -2 = Invalid public key -1 = Waiting for certificate 0 = Not installed 1 = Active...

VIVOTEK 156 - User's Manual 8. Useful Functions 8.1 Drive the Digital Output (capability.ndo > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/dido/setdo.cgi?do1= <state> [&do2=<state>] [&do3=<state>][&do...

VIVOTEK User's Manual - 157 Example: Query the status of digital input 1. Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1\r\n 8.3 Query Status of the Digital Output (capability.ndo > 0) Note: This requ...

VIVOTEK 158 - User's Manual 8.4 3D Privacy Mask Note: This request requires admin user privilege <SD81X1> You can set privacy mask only at zoom 1x. To go back to zoom 1x directly, please send this cgi command: "/cgi-bin/camctrl/camposition.cgi?setzoom=0" Method: GET/POST Syntax: http:/...

VIVOTEK User's Manual - 159 The server will return the most up-to-date snapshot of the selected channel and stream in JPEG format. The size and quality of the image will be set according to the video settings on the server. Return: HTTP/1.0 200 OK\r\n Content-Type: image/jpeg\r\n [Content-Length: &l...

VIVOTEK 160 - User's Manual 8.7 System Logs Note: This request require Administrator privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/admin/syslog.cgi Server will return the most up-to-date system log. Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: &...

VIVOTEK 162 - User's Manual zooming wide or tele Zoom without stopping for larger view or further view with zs speed, used for joystick control. zs 0 ~ 6 0 ~ 15 <SD81X1> Set the speed of zooming, “0” means stop. vx <integer , excluding 0> vy <integer> The slope of movement = vy/vx,...

VIVOTEK User's Manual - 165 http://< servername >/cgi-bin/camctrl/eRecall.cgi?channel=<value>&stream=<value>& recall=<value>[&return= <return page> ] PARAMETER VALUE DESCRIPTION channel <0~(n-1)> Channel of the video source. stream <0~(m-1)> Stre...

VIVOTEK User's Manual - 167 8.16 UART HTTP Tunnel Channel (capability.nuart > 0) Note: This request requires Operator privileges. Method: GET and POST Syntax: http://< servername >/cgi-bin/operator/uartchannel.cgi?[channel=<value>] -----------------------------------------------------...

VIVOTEK 168 - User's Manual Syntax: http://< servername >/cgi-bin/admin/ctrlevent.cgi ------------------------------------------------------------------------- GET /cgi-bin/admin/ctrlevent.cgi x-sessioncookie: string[22] accept: application/x-vvtk-tunnelled pragma: no-cache cache-control: no-c...

VIVOTEK User's Manual - 169 8.19 Open the Network Stream Note: This request requires Viewer access privileges. Syntax: For HTTP push server (MJPEG): http://< servername >/<network_http_s<0~m-1>_accessname> For RTSP (MP4), the user needs to input the URL below into an RTSP compatibl...

VIVOTEK User's Manual - 177 Technical Specifications Technical Specifications F i x e d N e t w o r k C a m e r a IP8151&IP8151P Supreme Night Visibility • Full Frame Rate • 1.3MP Ver 1.0 VIVOTEK INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho,Taipei County, Taiwan | T : +886-2-82455282 | F : +886-2-8...

VIVOTEK 178 - User's Manual Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE� THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOS...

VIVOTEK User's Manual - 179 Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15� Operation is subject to the following two conditions� ■ This device may not cause harmful interference, and■ This device must accept any interference received, including interfe...