Vivotek IP7361 - Manuals

VIVOTEK User's Manual - 5 DI/DO Diagram Please refer to the following illustration for the connection method� 12V +12V Digital output PIN 1Power+12V PIN 2 Digital input PIN 3 Ground PIN 4 Status LED The LED indicates the status of the Network Camera� Item LED status Description 1 Steady Red Power on...

VIVOTEK 6 - User's Manual Hardware Reset The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again� Reset: P...

VIVOTEK User's Manual - 7 Cabling Assembly 1 2 3 4 5 6 7 8 (D) (B) (C) (A) (E) Components of the Waterproof Connector Screw Nut (C) Housing (D) Gasket (E) Seal (B) Sealing Nut (A) RJ45 Cable Dimension (unit: mm) Prepare an Ethernet cable and strip part of the sheath� Insert the housing into the scre...

VIVOTEK 8 - User's Manual Hardware Installation 1� Attach the alignment sticker to the wall� Drill four holes into the wall� Then hammer the supplied plastic anchors into the holes and secure the plate with supplied screws� 2� Fix the ㄇ -bracket to the side of the Network Camera with two screws� 3. ...

VIVOTEK User's Manual - 9 Waterproof Connector 1 Power +12V 2 Digital Output 3 Digital Input 4 Ground 5 AC 24V 6 AC 24V 7 RS485 + 8 RS485 - 1 External MIC In 2 Ground 3 Audio Out 4 Ground 8 7 6 5 4 3 2 1 4 3 2 1 1� Disassemble the components of the waterproof connector into part (A) ~ (E) as shown a...

VIVOTEK 10 - User's Manual Network Deployment Setting up the Network Camera over the Internet There are several ways to set up the Network Camera over the Internet � The first way is to set up the Network Camera behind a router � The second way is to utilize a static IP � The third way is to use PPP...

VIVOTEK User's Manual - 11 Internet connection with static IP Choose this connection type if you are required to use a static IP for the Network Camera. Please refer to LAN on page 38 for details� Internet connection via PPPoE (Point-to-Point over Ethernet) Choose this connection type if you are con...

VIVOTEK 12 - User's Manual Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enable...

VIVOTEK User's Manual - 13 Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double click the IW2 shortcut on your desktop to ...

VIVOTEK 14 - User's Manual Ready to Use 1� Access the Network Camera on the LAN�2� Retrieve live video through a web browser or recording software� 3� Unscrew the zoom controller to adjust the zoom factor� Upon completion, tighten the zoom controller� 4� Unscrew the focus controller to adjust the fo...

VIVOTEK User's Manual - 15 5� Tighten the lens cover�6� Open the back cover� 7� Tear down the aluminum foil vacuum bag and take out the silica gel� Attach the silica gel to the inner side of the back cover, then tighten the back cover� (Please replace the silica gel with a new one if you open the ba...

VIVOTEK 16 - User's Manual Accessories VIVOTEK also provides other accessories for versatile applications as the following illustrations� Please visit VIVOTEK's official website for more purchase information. The 30m, 60° IR illuminator extends the coverage of the Network Camera and reduces the halo...

VIVOTEK User's Manual - 17 Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on th...

VIVOTEK 18 - User's Manual ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 31� ► If you see a ...

VIVOTEK User's Manual - 19 Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player mpegable Player pvPlayer As most ISPs and players only allow RTSP streaming throug...

VIVOTEK 20 - User's Manual Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Ne...

VIVOTEK User's Manual - 21 Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera to the Cha...

VIVOTEK 22 - User's Manual Main Page This chapter explains the layout of the main page� It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website� Host N...

VIVOTEK User's Manual - 23 Configuration Area Client Settings: Click this button to access the client setting page� For more information, please refer to Client Settings on page 26� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a passwo...

VIVOTEK User's Manual - 25 Snapshot: Click this button to capture and save still images� The captured images will be displayed in a pop-up window� Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP (*.bmp) format. Digital Zoom : Click and uncheck “Disable digital zoom...

VIVOTEK 26 - User's Manual Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer� When completed with the settings on this page, click Save on the page bottom to enable the settings� MPEG-4 Media Options Select to stream video or au...

VIVOTEK User's Manual - 27 MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and file name. Folder : Specify a storage destination for the recorded video files. File name prefix: Ente...

VIVOTEK 28 - User's Manual Configuration Click Configuration on the main page to enter the camera setting pages� Note that only Administrators can access the configuration page. VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with minimal effort� To simplify th...

VIVOTEK User's Manual - 29 Advanced Mode Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode � If you want to set up advanced functions, please click [Advanced Mode] on the bottom ...

VIVOTEK 30 - User's Manual System Time Keep current date and time: Select this option to preserve the current date and time of the Network Camera� The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off� Sync with computer time: Selec...

VIVOTEK User's Manual - 31 Security This section explains how to enable password protection and create multiple accounts� Root Password The administrator account name is “root”, which is permanent and can not be deleted� If you want to add more accounts in the Manage User column, please apply the pa...

VIVOTEK 32 - User's Manual HTTPS (Hypertext Transfer Protocol over SSL) Advanced Mode This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer)� It helps protect streaming data transmission over the Internet on higher security level� Enable HTTPS C...

VIVOTEK User's Manual - 33 4. The Certificate Information will automatically de displayed in the third column as shown below. You can click Property to view detailed information about the certificate. 5� Click Home to return to the main page� Change the address from “ http:// ” to “ https:// “ in th...

VIVOTEK 34 - User's Manual Create self-signed certificate manually 1� Select this option� 2� Click Create to open the Create Certificate page, then click Save to generate the certificate. 3. The Certificate Information will automatically be displayed in the third column as shown below. You can click...

VIVOTEK 36 - User's Manual 5� Look for a trusted certificate authority that issues digital certificates� Enroll the Network Camera� Wait for the certificate authority to issue a SSL certificate; click Browse... to search for the issued certificate, then click Upload in the second column. NOTE ► How ...

VIVOTEK User's Manual - 37 SNMP (Simple Network Management Protocol) Advanced Mode This section explains how to use the SNMP on the network camera� The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices�...

VIVOTEK 38 - User's Manual Network This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers� The default setting fo...

VIVOTEK 40 - User's Manual NOTE ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera� ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support U...

VIVOTEK User's Manual - 41 4� In the Networking Services dialog box, select Universal Plug and Play and click OK � 5� Click Next in the following window� 6� Click Finish � UPnP TM is enabled� ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic disco...

VIVOTEK 42 - User's Manual Enable IPv6 Select this option and click Save to enable IPv6 settings� Please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft ® Internet Explorer 6�5, Mozilla Firefox 3�0 or above� When IPv6 is enab...

VIVOTEK User's Manual - 43 Please follow the steps below to link to an IPv6 address: 1� Open your web browser� 2� Enter the link-global or link-local IPv6 address in the address bar of your web browser� 3� The format should be: 4� Press Enter on the keyboard or click Refresh button to refresh the we...

VIVOTEK 44 - User's Manual IEEE 802�1x Advanced Mode Enable this function if your network environment uses IEEE 802�1x, which is a port-based network access control� The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802�1x settings� The 802�1x stand...

VIVOTEK User's Manual - 45 3� When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802�1x enabled switch� The devices will then start the authentication automatically� NOTE ► The authentication process for 802�1x: 1� The Certificate Authority (CA) provi...

VIVOTEK 46 - User's Manual QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism , which guarantees a certain quality to different services on the network� Quality of service guarantees are important if the network capacity is insufficient, espe...

VIVOTEK User's Manual - 47 QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer)� The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Se...

VIVOTEK 48 - User's Manual HTTP Advanced Mode To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security on page 31 for details� Authentication : Depending on your network security requirements, the Network Camera provides two types...

VIVOTEK User's Manual - 49 URL command -- http://<ip address>:<http port>/<access name for stream 1 ~ 5> For example, when the Access name for stream 2 is set to video2�mjpg : 1� Launch Mozilla Firefox or Netscape� 2� Type the above URL command in the address bar� Press Enter � 3. ...

VIVOTEK 50 - User's Manual Note that as JPEG only transmits a series of JPEG images to the client, to enable the two-way audio function, make sure the video mode is set to “MPEG-4” on the Audio and Video Settings page and the media option is set to “Video and Audio” on the Client Settings page� Plea...

VIVOTEK User's Manual - 51 RTSP Streaming To utilize RTSP streaming authentication, make sure that you have set a password for the Network Camera first; please refer to Security on page 31 for details� Authentication : Depending on your network security requirements, the Network Camera provides thre...

VIVOTEK 52 - User's Manual RTSP port /RTP port for video, audio/ RTCP port for video, audio ■ RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default, the port number is set to 554� ■ The RTP (Real-time Transport Protocol) is used to deliver video and audio data to t...

VIVOTEK User's Manual - 53 DDNS This section explains how to configure the dynamic domain name service for the Network Camera� DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. DDNS: Dynamic domain name servic...

VIVOTEK 54 - User's Manual 4� Select Enable DDNS and click Save to enable the setting� ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators� You can use CustomSafe100 to register a dynamic domain name if your distributor or system ...

VIVOTEK User's Manual - 55 Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address� General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 and st...

VIVOTEK 56 - User's Manual ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access� Please note that those checked connections will only be disconnected temporarily and wi...

VIVOTEK User's Manual - 57 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List� For example: Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List� This rule is only applied to IPv4� For example: ■ De...

VIVOTEK 58 - User's Manual Audio and Video This section explains how to cofigure the audio and video settings of the Network Camera. It is composed of the following two columns: Video Settings and Audio Settings� Video Settings Video title: Enter a name that will be displayed on the title bar of the...

VIVOTEK User's Manual - 59 Overlay title and time stamp on video: Select this option to place the video title and time on the video streams� Note that when the frame size is set to 176 x 144 as shown in the picture below, only the time will be stamped on the video streams� Options of Video Advanced ...

VIVOTEK 60 - User's Manual White balance: Adjust the value for the best color temperature� ■ Auto The Network Camera automatically adjusts the color temperature of the light in response to different light sources� The white balance setting defaults to Auto and works well in most situations� ■ Keep c...

VIVOTEK User's Manual - 61 Enable Edge Enhancement Edge enhancement is an image processing filter that enhances the edge contrast of an image or video to improve its sharpness� Enter a value from 1 to 128 to set the degree of enhancement desired� Enable Noise Reduction Noise reduction is the process...

VIVOTEK 62 - User's Manual Sensor Settings Advanced Mode Click Sensor Settings to open the Sensor Settings page� On this page, you can set the maximum exposure time, exposure level, and AGC (Auto Gain Control) settings� You can configure two sets of sensor settings: one for normal situations, the ot...

VIVOTEK User's Manual - 63 If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Sensor Settings Profile Settings page as shown below. Please follow the steps beolw to setup a profile: 1� Check Enable this profile � 2� Select the applied mode: ...

VIVOTEK 64 - User's Manual Viewing Window Advanced Mode Click Viewing Window to open the Viewing Window Settings page� This Network Camera supports multiple streams with frame size ranging from 176 x 144 to 1600 x 1200� The definition of multiple streams: ■ Stream 1: Users can define the "Region...

VIVOTEK User's Manual - 65 Click Viewing Window to open the viewing region settings page� On this page, you can set the Region of Interest and the Output Frame Size for stream 1 ~ 3� Please follow the steps below to set up those settings for a stream: 1� Select a stream which you want to set up the ...

VIVOTEK 66 - User's Manual Cropping Setting Advanced Mode Click Cropping Setting to open the Cropping Settings page� Please follow the steps below to set up cropping mode for mutiple streams: 1� Click Cropping Setting to open the window as shown below� 2� Select a Captured area from the drop-down li...

VIVOTEK User's Manual - 67 Video Quality Settings Click the stream item to display the detailed information� The maximum frame size will follow your settings in above sections� This Network Camera offers real-time MPEG-4 and MJEPG compression standards (dual codec) for real-time viewing� If MPEG-4 m...

VIVOTEK 68 - User's Manual ■ Intra frame period Determine how often to plant an I frame� The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption. Select the intra frame period from the following durations: 1/4 second, 1/2 s...

VIVOTEK User's Manual - 69 Day/Night Settings Switch to B/W in night mode Select this to enable the Network Camera to automatically switch to B/W during night mode� IR cut filter With a removable IR-cut filter, this Network Camera can automatically remove the filter to let IR light into the sensor d...

VIVOTEK 70 - User's Manual Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients� Note that if mute mode is turned on, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page� In that case, the followi...

VIVOTEK User's Manual - 71 Motion Detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Follow the steps below to enable motion detection:Follow the steps below to enable motion detection: 1� Click...

VIVOTEK 72 - User's Manual A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. If you want to configure other motion detection settings for day/night/schedule mode, please click Profi...

VIVOTEK User's Manual - 73 NOTE ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage� In the illustration above, frame A and frame B are two sequential images. Pixel differences between the two frames are detected and highlighted in gray (frame C) a...

VIVOTEK 74 - User's Manual Camera Tampering Detection This section explains how to set up camera temper detection� With tamper detection, the camera is capable of detecting incidents such as redirection , blocking or defocusing , or even spray paint � Please follow the steps below to set up the came...

VIVOTEK User's Manual - 75 Camera Control This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation. There are two ways to enable the camera control function: 1. Mechanical: Connect the Network Camera to a PTZ driver or scanner via RS485 interface. 2. Digital: Control the e-P...

VIVOTEK 76 - User's Manual Transparent HTTP Tunnel: If you want to use your own RS-485 device, you can use UART commands to build a Transparent HTTP Tunnel� The UART commands will be sent through HTTP tunnel established between the RS-485 device and the linked camera� For detailed application notes,...

VIVOTEK User's Manual - 77 Home page in Mechanical PTZ Mode The Preset Positions will also be displayed on the home page� Select one from the drop-down list, and the Network Camera will move to the selected preset position�

VIVOTEK 78 - User's Manual Patrol Settings You can select some preset positions for the Network Camera to patrol� Please follow the steps below to set up a patrol schedule: 1� Click a preset location on the list and click Select � 2� The selected preset location will be displayed on the Source list�...

VIVOTEK User's Manual - 79 Custom Command If Custom Camera (scanner) is selected as the PTZ driver, you will need to configure command buttons to control the PTZ scanner. Click Custom Command to open the Custom Command page to set the commands in the Control Settings session. Please refer to your PT...

VIVOTEK 80 - User's Manual E-PTZ Operation If you select “Digital“, the e-PTZ control settings section will be displayed as shown below: Select Stream : Select one of the stream 1~3 to set up the e-PTZ control. Please note that each stream can be set up with its own e-preset positions and e-patrol s...

VIVOTEK User's Manual - 81 Home page in E-PTZ Mode ■ The e-Preset Positions will also be displayed on the home page� Select one from the drop-down list, and the Network Camera will move to the selected e-preset position� ■ If you have set up different e- preset positions for stream 1~3, you can sele...

VIVOTEK 82 - User's Manual Homepage Layout Advanced Mode This section explains how to set up your own customized homepage layout� Preview This column shows the settings of your hompage layout� You can manually select the background and font colors in Theme Options (the third column on this page)� Th...

VIVOTEK User's Manual - 83 Theme Options Here you can change the color of your homepage layout� There are three types of preset patterns for you to choose from� The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings� Font Color of the Video Title Font Color...

VIVOTEK User's Manual - 85 Application Advanced Mode This section explains how to configure the Network Camera to responds to particular situations (event)� A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notific...

VIVOTEK 86 - User's Manual Event Settings In the Event Settings column, click Add to open the Event Settings page. On this page, you can arrange three elements -- Trigger, Schedule, and Action to set an event. A total of 3 event settings can be configured. Event name: Enter a name for the event sett...

VIVOTEK User's Manual - 87 An event is an action initiated by a user-defined trigger source; it is the causal arrangement of the following three elements: Trigger, Event Schedule, and Action. Trigger This is the cause or stimulus which defines when to trigger the Network Camera. The trigger source c...

VIVOTEK 88 - User's Manual ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with. To enable this function, you need to configure the Tampering Detection option first. Please refer to page 74 for detailed information. Even...

VIVOTEK User's Manual - 89 To set an event with recorded video or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take ( such as which server to send the media files to) when a trigger is activated. ■ Add Server / Add Media Cl...

VIVOTEK 90 - User's Manual When completed, click Save to enable the settings and click Close to exit Event Settings page. The new event settings / server settings / media settings will appear in the event drop-down list on the Application page. Here is an example of the Application page with an even...

VIVOTEK User's Manual - 91 Server Settings Click Add Server on Event Settings page to open the Server Setting page. On this page, you can specify where the notification messages are sent when a trigger is activated. A total of 5 server settings can be configured. Server name: Enter a name for the se...

VIVOTEK 92 - User's Manual FTP: Select to send the media files to an FTP server when a trigger is activated. ■ Server address: Enter the domain name or IP address of the FTP server. ■ Server port By default, the FTP server port is set to 21. It can also be assigned to another port number between 102...

VIVOTEK 94 - User's Manual Media Settings Click Add Media on the Event Settings page to open the Media Settings page. On this page, you can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. Media name : Enter a name for the media ...

VIVOTEK 96 - User's Manual You can continue to select a server and media type for the event. Please go back to page 66 for detailed information. ■ SD Test: Click to test your SD card. The system will display a message indicating success or failure. If you want to use your SD card for local storage, ...

VIVOTEK User's Manual - 97 The following is an example of a file destination with video clips: Click 20081120 to open the directory: 20081120 20081121 20081122 Click to delete selected items Click to delete all recorded data The format is: YYYYMMDD Click to open the directory Click to delete selecte...

VIVOTEK 98 - User's Manual Recording Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE ► Before setting up this page, please set up the Network Storage on the Server Settings page first. ► Please remember to format your SD car...

VIVOTEK User's Manual - 99 If successful, you will receive a test.txt file on the network storage server. 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. Recording Settings Click Add to open the recording setting page. In this page, you can define the...

VIVOTEK User's Manual - 101 Local Storage Advanced Mode This section explains how to manage the local storage on the Network Camera. Here you can view SD card status, search for recorded files to playback, download, etc. SD Card Management SD card status: This column shows the status and reserved sp...

VIVOTEK 102 - User's Manual SD card control ■ Enable cyclic storage: Check this item if you want to enable cyclic recording. When the maximum capacity is reached, the oldest file will be overwritten by the latest one. ■ Enable automatic disk cleanup: Check this item and enter the number of days you ...

VIVOTEK User's Manual - 103 Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked. Click to sort the search results in either direction. View: Click on a search result which will highlight the selected item in purple ...

VIVOTEK 104 - User's Manual Download : Click on a search result to highlight the selected item in purple as shown above. Then click the Download button and a file download window will pop up for you to save the file. JPEGs to AVI: This functions only applies to “JPEG“ format files such as snapshots....

VIVOTEK User's Manual - 105 System Log Advanced Mode This section explains how to configure the Network Camera to send the system log to the remote server as backup. Remote Log You can configure the Network Camera to send the system log file to a remote server as a log backup. Before utilizing this ...

VIVOTEK 106 - User's Manual View Parameters Advanced Mode The View Parameters page lists the entire system’s parameters in alphabetical order. If you need technical assistance, please provide the information listed on this page.

VIVOTEK User's Manual - 107 Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. Reboot This feature allows you to reboot the Network Camera, which takes about one minute to complete. When completed, the live video page will be displa...

VIVOTEK 108 - User's Manual Export / Upload Files Advanced Mode This feature allows you to Export / Upload daylight saving time rules, custom language files, and setting backup files. Export daylight saving time configuration file: Click to set the start and end time of DST. Follow the steps below t...

VIVOTEK User's Manual - 109 Upload daylight saving time rule: Click Browse… and specify the XML file to upload. If the incorrect date and time are assigned, you will see the following warning message when uploading the file to the Network Camera. The following message is displayed when attempting to...

VIVOTEK User's Manual - 111 Appendix URL Commands for the Network Camera Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based application...

VIVOTEK 112 - User's Manual 1. General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camer...

VIVOTEK 114 - User's Manual 3. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://< servername >/cgi-bin/ anonymous /getparam.cgi?[ <parameter> ] [&<parameter>…] http://< servername >/cgi-bin/ viewer /getparam....

VIVOTEK 116 - User's Manual 4. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://< servername >/cgi-bin/ anonymous /setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&update=<value>][&a...

VIVOTEK 118 - User's Manual 5. Available Parameters on the Server This chapter defines all the parameters which can be configured or retrieved from VIVOTEK network camera or video server. The general format of description is listed in the table below Valid values: VALID VALUES DESCRIPTION string[<...

VIVOTEK 122 - User's Manual serialnumber <mac address> 0/7 12 characters MAC address (without hyphens). firmwareversion string[40] 0/7 Firmware version, including model, company, and version number in the format: <MODEL-BRAND-VERSION> language_count <integer> 0/7 Number of webpage ...

VIVOTEK User's Manual - 123 5.4 Digital Output Behavior Define Group: do_i<0~(ndo-1)> (capability.ndo > 0) 5.5 Security Group: security NAME VALUE SECURITY (get/set) DESCRIPTION privilege_do view, operator, admin 6/6 Indicate which privileges and above can control digital output privilege_c...

VIVOTEK User's Manual - 131 Group: videoin_profile_i<0~(m-1)> NAME VALUE SECURIT Y (get/set) DESCRIPTION enable <boolean> 4/4 Enable/disable this profile setting policy day, night, schedule 4/4 The mode which the profile is applied to. begintime hh:mm 4/4 Begin time of schedule mode. end...

VIVOTEK 132 - User's Manual 5.10 IR Cut Control Group: ircutcontrol NAME VALUE SECURITY (get/set) DESCRIPTION mode auto, day, night, di, schedule 6/6 Set IR cut control mode daymodebegintime 00:00~23:59 6/6 Day mode begin time daymodeendtime 00:00~23:59 6/6 Day mod end time disableirled <boolean&...

VIVOTEK User's Manual - 133 5.12 Image Setting for Preview Group: imagepreview_c<0~(n-1)> for n channel products NAME VALUE SECURITY (get/set) DESCRIPTION brightness <product dependent> 4/4 Preview of brightness adjustment of image according to mode settings. saturation -5 ~ 5 4/4 Previe...

VIVOTEK 134 - User's Manual 5.13 Audio Input per Channel Group: audioin_c<0~(n-1)> for n channel products (capability.audioin>0) NAME VALUE SECURITY (get/set) DESCRIPTION mute 0, 1 4/4 Enable audio mute. gain 0~31 4/4 Gain of input. s<0~(m-1)>_codectype gamr 4/4 Set audio codec type f...

VIVOTEK User's Manual - 135 profile_i<0~(m-1)>_policy day, night, schedule 4/4 The mode which the profile is applied to. profile_i<0~(m-1)>_begintime hh:mm 4/4 Begin time of schedule mode. profile_i<0~(m-1)>_endtime hh:mm 4/4 End time of schedule mode. profile_i<0~(m-1)>_win_...

VIVOTEK 136 - User's Manual CustomSafe100 => Custom server using safe100 method <provider>_hostname string[128] 6/6 Your dynamic hostname. <provider>_username email string[64] 6/6 Your user or email to login to the DDNS service provider <provider>_password key string[64] 6/6 You...

VIVOTEK User's Manual - 137 3: LOG_ERR 4: LOG_WARNING 5: LOG_NOTICE 6: LOG_INFO 7: LOG_DEBUG 5.21 Camera PTZ Control Group: camctrl (product dependent) NAME VALUE SECURITY (get/set) DESCRIPTION enablehttptunnel <boolean> 4/4 Enable HTTP tunnel for camera control. Group: camctrl_c<0~(n-1)>...

VIVOTEK User's Manual - 139 authpwro string[8~128] 6/6 Read only authentication password authtyperw MD5,SHA 6/6 Read/write authentication type authtypero MD5,SHA 6/6 Read only authentication type encryptpwrw string[8~128] 6/6 Read/write password encryptpwro string[8~128] 6/6 Read only password encry...

VIVOTEK User's Manual - 143 l network wireless_endchannel 1 ~ 14 0/7 Indicate the end channel of wireless network wireless_encrypt_wep <boolean> 0/7 Indicate whether to support wireless WEP. wireless_encrypt_wpa <boolean> 0/7 Indicate whether to support wireless WPA. wireless_encrypt_wpa...

VIVOTEK User's Manual - 145 lowlightcondition 0, 1 6/6 0 => Do action at all times 1 => Do action in low-light conditions action_do_i<0~(ndo-1)>_ena ble 0, 1 6/6 Enable or disable trigger digital output. action_do_i<0~(ndo-1)>_dur ation 1~999 6/6 Duration of the digital output trig...

VIVOTEK 146 - User's Manual ftp_passive 0, 1 6/6 Enable or disable passive mode. 0 = disable passive mode 1 = enable passive mode email_address string[128] 6/6 Email server address. email_sslmode 0, 1 6/6 Enable support SSL. email_port 0~65535 6/6 Port to connect to the server. email_username string...

VIVOTEK User's Manual - 149 policy <Boolean> 6/6 If the value is 1, it will force HTTP connection redirect to HTTPS connection method auto, manual, install 6/6 auto => Create self-signed certificate automatically. manual => Create self-signed certificate manually. install => Create ce...

VIVOTEK User's Manual - 151 6. Useful Functions 6.1 Drive the Digital Output Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/dido/setdo.cgi?do1= <state> [&do2=<state>] [&do3=<state>][&do4=<state>][&re...

VIVOTEK 152 - User's Manual [di2=<state>]\r\n [di3=<state>]\r\n where <state> can be 0 or 1. Example: Query the status of digital input 1. Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1...

VIVOTEK User's Manual - 153 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n do1=1\r\n 6.4 Drive the IR Light Illuminator Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/dido/setilluminator.cgi?ir_status...

VIVOTEK 154 - User's Manual where <state> can be 0 or 1. Example: Query the status of IR illuminator. Request: http://myserver/cgi-bin/dido/getilluminator.cgi?ir_status Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n ir_status=1\r\n 6.6 Capture Single Snapshot Note: This request req...

VIVOTEK User's Manual - 155 6.7 Account Management Note: This request requires Administrator privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/admin/editaccount.cgi ? method=<value>&username= <name> [&userpass= <value> ][&privilege= <value> ...

VIVOTEK 156 - User's Manual Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: <syslog length>\r\n \r\n <system log information>\r\n 6.9 Configuration File (optional) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http://< serverna...

VIVOTEK 158 - User's Manual auto Auto focus. far Focus on further distance. focus near Focus on closer distance. auto Let the Network Camera control iris size. open Manually control the iris for bigger size. iris close Manually control the iris for smaller size. speedlink 0 ~ 4 Issue speed link comm...

VIVOTEK 160 - User's Manual recall=<value>[&return= <return page> ] PARAMETER VALUE DESCRIPTION channel <0~(n-1)> Channel of the video source. stream <0~(m-1)> Stream. Recall Text string less than 40 characters One of the present positions to recall. Return <return pag...

VIVOTEK 162 - User's Manual return <return page> Redirect to the page <return page> after the parameter is assigned . The <return page> can be a full URL path or relative path according to the current path. If you omit this parameter, it will redirect to an empty page. 6.18 UART HT...

VIVOTEK User's Manual - 163 6.19 Event/Control HTTP Tunnel Channel Note: This request requires Administrator privileges. Method: GET and POST Syntax: http://< servername >/cgi-bin/admin/ctrlevent.cgi ------------------------------------------------------------------------- GET /cgi-bin/admin/c...

VIVOTEK 164 - User's Manual “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1” to stream “m”. Please refer to the “subgroup of network: rtsp” for setting the accessname of SDP. You can get the SDP by HTTP GET. When using scalable multicast, Get SDP file w...

VIVOTEK User's Manual - 165 Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: <system information length>\r\n \r\n <hex decimal data>\r\n Where hexadecimal data is digits from 0 ~ 9, A ~ F. 6.23 Storage Managements (capability.storage.dbenabled=1) Note: This reques...

VIVOTEK 168 - User's Manual Technical Specifications Technical Specifications Alarm and Event Management ． Triple-window video motion detection ． Tamper detection ． One D/I and one D/O for external sensor and alarm ． Event notification using HTTP, SMTP or FTP ． Local recording of MP4 file On-board S...

VIVOTEK User's Manual - 169 Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOS...

VIVOTEK 170 - User's Manual Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions.■ This device may not cause harmful interference, and■ This device must accept any interference received, including interfer...