Vantec UGT-ST310R - Manuals

Page 2 - Table of Contents

UGT-ST310R Page 2 Table of Contents 1. Bus Interface .......................................... 3 2. Connectors............................................. 3 3. Package Contents .................................. 3 4. System Requirements ............................ 4 5. Hardware Description..........

Page 3 - Features; Bus Interface

UGT-ST310R Page 3 Features • Silicon Image SiI3114 SATA controller chip • Compliant with PCI Specification, Rev. 2.3, 32-bit, 33/66Mhz • Compliant with Serial ATA 1.0 specification • Provides four independent channels to support up to four Serial ATA drives • Supports RAID0 (striping), RAID1 (mirror...

Page 4 - System Requirements; Hardware Description; JP

System Requirements z Pentium-class computer with one available PCI slot z Windows® 2000, XP/2003 32/64bit, Vista 32/64bit Hardware Description G (Jumper Settings) JP Description Active Port 1-2 close Enable SATA Connector F J1-J4 2-3 close Enable SATA Connector C 1-2 close Enable SATA Connector E J...

Page 6 - RAID Arrays

UGT-ST310R Page 6 drive. 4. Attach the other end of the Serial ATA cable to the Serial ATA controller on the 6-Port SATA II 150 PCI Host Card w/RAID. 5. Follow the same instructions to connect up to four hard drives. Device connection is now complete. 6. Replace the computer cover and reconnect the ...

Page 7 - Manual configuration

UGT-ST310R Page 7 3. Select RAID0 , then press Enter . 4. Select the number of drives then press Enter . 5. Select Auto configuration , then press Enter . 6. Input the RAID size, press Enter . 7. When asked Are You Sure (Y/N)? , press Y to accept. 8. Press Ctrl+E to exit the BIOS. 9. When asked Are ...

Page 8 - For New/Blank Hard Drives

UGT-ST310R Page 8 RAID 1 (Mirror) For New/Blank Hard Drives 1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS. 2. At the next screen select Create RAID Set , then press Enter . 3. At the next screen select RAID1 then press Enter . 4. Select Auto configuration , then press ...

Page 9 - Rebuilding a Failed Mirror Set

UGT-ST310R Page 9 9. Input the RAID size, press Enter . 10. Press Ctrl+E to exit the BIOS. 11. When asked Are you sure to exit(Y/N)? , press Y to exit and reboot. Note: If during boot the RAID BIOS reports an RAID1 set is in Rebuild status, The rebuild will continue after boot sequence is complete ,...

Page 15 - A new installation requires a floppy disk for the driver; Enter

UGT-ST310R Page 15 F BIOS Configuration The 6-Port SATA II 150 PCI Host Card w/RAID BIOS will appear every time your system starts up. If the BIOS doesn’t show, please try your controller in another PCI slot. During this (POST) process, the BIOS will show up and indicate the devices attached to it. ...

Page 16 - For Windows® XP/Server 2003

UGT-ST310R Page 16 F to Windows. 2. At Found New Hardware Wizard , click Next . 3. Select Search for a suitable driver for my device (recommend) then click Next . 4. Insert the driver CD, check CD-ROM drives , uncheck the other boxes, click Next , then click Next again. 5. If the Digital Signature N...

Page 18 - For Windows® Vista

1. Setup the RAID Array prior to driver installation and boot up to Windows. 2. At the Found New Hardware Wizard, select No, not this time, then click Next. 3. Insert the driver CD, select Install the software automatically (Recommended) , and click Next . 4. Click Finish . 5. Restart Windows to com...

Page 19 - To Verify Windows® Installation; For Windows® Vista-x64

UGT-ST310R Page 19 F To Verify Windows® Installation 1. Right click My Computer and click Manage . 3. Please insert driver CD, click Next . 4. Click Close to complete the installation. For Windows® Vista-x64 or A New Installation A new installation requires a floppy disk for the driver installation....